• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.6 no.1
• /
• pp.50-56
• /
• 2010

Fatigue has been known as a major degradation mechanism of ASME class 1 components in nuclear power plants. Fatigue damage could be accelerated by combined interaction of several loads and environmental factors. However, the environmental effect is not explicitly addressed in the ASME S-N curve which is based on air at room temperature. Therefore many studies have been performed to understand the environmental effects on fatigue behavior of materials used in nuclear power plants. As a part of efforts, we performed low cycle fatigue tests under various environmental conditions and analyzed the environmental effects on the fatigue life of SA508 Gr. 1a low alloy steel by comparing with higuchi's model. Test results show that the fatigue life depends on water temperature, dissolved oxygen and strain rate. But strain rate over 0.4%/s has little effect on the fatigue life. To find the cause of different fatigue life with ANL's and higuchi's model, another test performed with different heat numbered and heat treated materials of SA508 Gr. 1a. On a metallurgical point of view, the material with bainite microstructure shows much longer fatigue life than that with ferrite/pearlite microstructure. And the characteristics of crack propagation as different microstructure seem to be the main cause of different fatigue life.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.6
• /
• pp.1107-1113
• /
• 2002

This study presents the hydrogen emblittlement in the metal, which decreases the ductility and then induces the brittle fracture. The contribution deals with the effect of strain rate and notch geometry on hydrogen emblittlement of 1.25Cr-0.5Mo and 2.25Cr-1Mo steels, which are in use at high pressure vessel. Smooth and notched specimens were examined to obtain the elongation and tensile strength. For charging the hydrogen in the metal, the cathodic electrolytic method was used. In this process, current density is maintained constant. The amount of hydrogen penetrated in the specimen was detected by the hydrogen determenator(LECO RH404) with the various charging time. The distribution of hydrogen concentration penetrated in the specimen was obtained by finite element analysis. The amount of hydrogen is high in smooth specimen and tends to concentrate in the vicinity of surface. The elongation and tensile strength decreased with the passage of charging time in 1.25Cr-0.5Mo and 2.25Cr-1Mo steels. The elongation increased and tensile strength decreased as strain rate increased. As a result of this study, it is supposed that 1.25Cr-0.5Mo steel is more sensitive than 2.25Cr-lMo steel in hydrogen embrittlement. Hydrogen embrittlement susceptibility of notched specimen after hydrogen charging is more remarkable than that of smooth specimen.

• Journal of Korea Multimedia Society
• /
• v.17 no.2
• /
• pp.124-131
• /
• 2014

In this paper, we propose the non-contact gesture recognition algorithm using 4- channel electrometer sensor array. ELF(Extremely Low Frequency) EMI and PLN are minimized because ambient electromagnetic noise around sensors has a significant impact on entire data in indoor environments. In this study, we transform AC-type data into DC-type data by applying a 10Hz LPF as well as a maximum buffer value extracting algorithm considering H/W sampling rate. In addition, we minimize the noise with the Kalman filter and extract 2-dimensional movement information by taking difference value between two cross-diagonal deployed sensors. We implemented the DTW gesture recognition algorithm using extracted data and the time delayed information of peak values. Our experiment results show that average correct classification rate is over 95% on five-gesture scenario.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.29-36
• /
• 2008

In this paper, the orbital forming analysis of an automotive hub bearing was studied to predict forming performances using the explicit finite element method. To find an efficient solution technique for the orbital forming, axisymmetric finite element models and 3D solid element models were solved and numerically compared. The time scaling and mass scaling techniques were introduced to reduce the excessive computational time caused by small element size in case of the explicit finite element method. It was found from the numerical simulations on the orbital forming that the axisymmetric element models showed the similar results to the 3D solid element models in forming loads whereas the deformations at the inner race of bearing were quite different. Finally the strains at the inner race of bearing and the forming forces to the peen were measured for the same product of the numerical model by test, and were compared with the 3D solid element results. It was founded that the test results were in good agreements with the numerical ones.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.4
• /
• pp.81-90
• /
• 2008

This paper presents a finite element formulation for the three-dimensional hierarchical solid element using Integrals of Legendre polynomials. The proposed hexahedral solid element is composed of four different modes including vertex, edge, face, and internal mode, respectively. The eigenvalue and patch test have been carried out to confirm the zero-energy mode and constant strain condition. In addition to these, a posteriori error estimation has been studied for the p-adaptive finite element analysis that is based on a smoothing technique to compute a post-processed solution from the finite element solution. The uniform p-refinement and non-uniform p-refinement are compared in terms of convergence rate as the number of degree of freedom is increased. The simple cantilever beam is tested to show the performance of the proposed solid element.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.12
• /
• pp.47-58
• /
• 1999

As the performance of processors improves, cache memories are used to overcome the difference of speed between processors and main memories. Generally cache memories are embedded and small sizes, fault coverage is a more important factor than test time in testing point of view. A new test algorithm and a new BIST architecture are developed to detect various fault models with a relatively small overhead. The new concurrent BIST architecture uses the comparator of cache management blocks as response analyzers for tag memories. A modified scan-chain is used for pre-testing of comparators which can reduce test clock cycles. In addition several boundary scan instructions are provided to control the internal test circuitries. The results show that the new algorithm can detect SAFs, AFs, TFs linked with CFs, CFins, CFids, SCFs, CFdyns and DRFs models with O(12N), where N is the memory size and the new BIST architecture has lower overhead than traditional architecture by about 11%.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.2
• /
• pp.61-71
• /
• 1993

The stress waves generated by the mechanical energies by impact or the chemical energies by the explosions are transmitted through medium. The wave propagation process through medium is a very complicated procedure due to the reflections and refractions of the waves at the free surfaces and interfaces. In this study the pressure independent Von-Mises model is employed for the wave propagation analysis in the layered systems. Governing equations of this study are conservation equations of momentum and mass in Lagrangian coordinate system which is fixed to the material. Due to the shock-front which violates the continuity assumptions inherent in the differential equations numerical artificial viscosity is used to spread the shock front over several computational zones. These equations are solved by Finite Difference Method with discretized time and space coordinates. The associate normality flow rule as a plastic theory is implemented to find the plastic strains.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.3
• /
• pp.11-21
• /
• 2002

The evaluation of displacement ductility is performed by direct method through tracking the inelastic hysteretic behavior of RC bridge columns subject to cyclic loading using a flexibility-based fiber element mode. To reasonably track the inelastic behavior until the RC bridge column reaches its ultimate state, the average stress-average strain relations and joint elements, which agree well with experiments, are modified and applied considering the tension stiffening behavior and discontinuous displacement between the column and its base. In addition the evaluation of displacement ductility is performed by a direct method easily applicable to numerical analysis. Locations for the integration points, values for the post-crushing concrete strength and low-cycle fatigue failure of longitudinal reinforcement that affect the calculation of yielding and ultimate displacements are proposed for the application to flexibility-based fiber element model. Since less than 10% of error occurs during the displacement ductility analysis, the yielding and ultimate displacements evaluated by the applied analysis method and model appear to be valid.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.43-53
• /
• 2003

To get improved soil parameters in the laboratory tests, the effects of sample disturbance should be excluded as much as possible. A collaborative research between Dong-A University and PHRI (Japan) was conducted to investigate the effects of sample disturbance due to sampling techniques and samplers on Pusan clays. The results of unconfined compression and consolidation tests performed on the clay samples taken by them have been compared in terms of soil parameters and sample disturbance. As the result of the study, it was found that when the Korean sampler was used with a different technique of cleaning the borehole bottom and removing slime before inserting and penetrating the sampler tube, similar to the one commonly used in Japanese practice, the quality of samples could be greatly improved. Furthermore, the CRS test with the rate of 0.02%/min yielded larger values of consolidation parameters and better degree of sample disturbance than those of oedometer test, due to the difference in testing method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.2
• /
• pp.21-33
• /
• 1992

Under the intense-impulsive loading, structures are subjected to the wide range of pressures at an instantaneous time. The constitutive laws capable to describe the material behavior under the extreme pressure as well as the low pressure are necessary for the analysis of the structural behavior under the intense -impulsive loadings. In this study, two plastic models, the pressure independent Von-Mises model and the pressure dependent Drucker-Prager model, are employed for the wave propagation analysis. Governing equations of this study are conservation equations of momentum and mass in Lagrangian coordinate system which is fixed to the material. Due to the shock-front which violates the continuity assumptions inherent in the differential equations numerical artificial viscosity is used to spread the shock front over several computational zones. These equations are solved by Finite Difference Method with discretized time and space coordinates. The associate normality flow rule as a plastic theory is implemented to find the plastic strains.