• Journal of the Korean Orthopaedic Association
• /
• v.55 no.2
• /
• pp.154-161
• /
• 2020

Purpose: To describe the clinical and radiology results of a surgical treatment for clinodactyly due to a longitudinal epiphyseal bracket. Materials and Methods: This study analyzed the records of 11 patients (27 case) with clinodactyly due to a longitudinal epiphyseal bracket who underwent an osteotomy or physiolysis between March 1999 and April 2017. The preoperative range of motion of the proximal and distal interphalangeal joints, the subjective satisfaction of the patient, and the degree of angulation to the ulnar side were examined. The patients were classified into two groups: osteotomy and physiolysis. The results were reviewed retrospectively and compared according to the surgical method. Results: The mean age of the patients who underwent osteotomy was 10.3 years. The average preoperative angle was 25.7° and the average postoperative angle was 13.5° the mean correction rate was 47.4%. The mean age of the patients who underwent physiolysis was 6.0 years the mean preoperative angle was 24.5° and the postoperative angle was 10.7°. The average correction rate was 59.4%. No significant difference in the correction angles was observed between the group who underwent the correction osteotomy and the group who underwent the osteotomy. In each group, the postoperative correction was statistically significant. The range of motion at the last follow-up was not significantly different from the preoperative range of motion. Conclusion: In patients with clinodactyly due to longitudinal epiphyseal bracket, osteotomy or physiolysis may be performed selectively according to age, bone age, and radiological progression. Both surgical methods showed good clinical results and deformity correction.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.5
• /
• pp.625-632
• /
• 2008

In the companion paper (Model Development), an analytical model estimating the available rotation capacity of fully restrained beam-column connections in special steel moment-resisting frames was proposed. In this paper, two limit states were considered as the connection rotation capacity criteria: (i) strength degradation failure when the strength falls below the nominal plastic strength due to the local buckling of the beam's cross-section and (ii) low-cycle fatigue fracture caused by plastic strain accumulation at the buckled flange after only a few cycles of high-amplitude deformation. A series of analyses are conducted using the proposed model with two limit states under monotonic and cyclic loadings. Beam section geometric parameters, such as flange and web slenderness ratios, varied over the practical ranges of H-shapedbeams to observe their effect on the rotation capacity and low-cycle fatigue life of pre-qualified WUF-W connections.

• Geotechnical Engineering
• /
• v.12 no.3
• /
• pp.17-34
• /
• 1996

The objective of this paper is to evaluate the asphalt mixture performance with pyrolyzed carbon black(CBP) and air -cooled iron blast furnace slag. Marshall mix design was performed to determine the optimum binder content, The optimum binder content ranged from 6.3 percent to 7.75 percent. Dynamic creep testing was carried out using mixtures at the optimum binder content. Based on the test results, the use of pyrolyzed carbon black and slag in the asphalt pavement showed a positive result, such as the increase of Marshall stability, the decrease of the strain rate and the decrease in the mix stiffness rate at high temperature(5$0^{\circ}C$) and 137.9 kPa confinement. Within the limits of this research. it was concluded that pyrolyzed carbon black as an additive and slag as a coarse aggregate could be used to produce an asphalt paving mixture that has good stability, stiffness, and rutting resistance.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.185-198
• /
• 1996

EPS is increasingly used as a filling material in soft ground. The beneficial effects of the use of EPS derive from minimizing the stress increment, which, in turn, increases the bearing capacity and reduces the settlement. EPS can also be used as a backfill material for retaining walls and abutments to reduce the horizontal earth pressure. However, there is no rational application for the selection of the EPS fill which is essential to the selection of the filling configuration and the settlement calculation. In this paper, therefore, the nonlinear numerical model developed from the results of triaxial compression tests is applied to the construction of EPS and verified through the comparison between the prediction and in-situ measurements.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.163-184
• /
• 1996

In this study, physical and geotechnical properties of the light weight mixed soil( weathered granite soil mixed with small pieces of waste EPS) were analyzed by laboratory experiments to examine its suitability for backfill materials of the reinforced-earth walls. Friction characteristics of geogrid-light weight sized soil were also investigated by performing the pullout tests for two types of geogrids having different flexural rigidity. Also a procedure was proposed to evaluate friction strength between geogrid and light weight miffed soil by using a stress-strain relationship of the orthotropic composite material subjected to both longitudinal and vertical loadings. By the procedure proposed in this study, values of the calibration coefficients ul and uf applicable for the evaluation of friction strengths between two types of geogrids and light weight mixed soils were further presented.

• Journal of the Korea Concrete Institute
• /
• v.23 no.2
• /
• pp.185-193
• /
• 2011

In the present study, a unified shear design method was developed to evaluate the shear strength of concrete beams with and without FRP shear reinforcement. The contributions of FRP and concrete on shear strength were defined separately. By comparing the current design method calculated results with the existing test results, it was found that Triantafillou model shows a reliable prediction of FRP effective strain and FRP shear strength contributions. The concrete shear strength contribution was defined by the strain-based shear strength model developed in the previous study. The shear strength of concrete compression zone was evaluated based on the material failure criteria of the concrete subjected to the compressive normal and shear stresses. The proposed strength model was verified by comparing its prediction results to prior test results. The comparisons showed that the proposed method accurately predicts the strengths of the test specimens for both FRP shear reinforced and unreinforced concrete beams.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.357-363
• /
• 2016

To solve the exhaustion problem of natural aggregate which were create the high value in construction and environmental industry, recycled aggregates have considerable benefits than other materials. However, even though many researches have been conducted with recycled aggregates, building structures with recycled aggregated are rarely constructed because it has lower quality than natural aggregates have. In this study, mechanical and strain properties of recycled aggregates concrete containing steel fibers have been reviewed in order to complement performance of recycled aggregates concrete. As results, recycled aggregates concrete showed lower compressive strength and elastic modulus than plain concrete. But, recycled aggregates concrete containing steel fibers showed equivalent performance with plain concrete. In review of drying shrinkage and creep coefficient, recycled aggregates concrete containing steel fibers showed similar behavior with plain concrete in the range of 0.5 Vol.% fiber content rate by internal restraint effect, moisture transport restraint effect and strength enhancement effect of steel fiber. Therefore, it is considered that mixing steel fibers with concrete is the effective method as a active application plan for recycled aggregates.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1155-1160
• /
• 2011

High-strength nickel-based super alloys have been widely used in aircraft engines, vessel engines, and turbine blades because of their high strength and excellent fatigue and oxidation resistance. In this study, tests were carried out to determine the total strain range and temperature for high-strength nickel-based super alloys. Prepared specimens of IN738LC were exposed to temperatures of $871^{\circ}C$ and $982^{\circ}C$ for 1,000.10,000 h. These specimens were subjected to tests of mechanical properties and microstructure observations. The changes in mechanical properties were related to changes in ${\gamma}$ according to the thermal exposure time.

• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.625-632
• /
• 2010

The moduli of concrete has been determined by various testing methods. The impact resonance (IR) method has been shown to be truly a simple nondestructive testing method which produces consistent results. It is possible to determine not only the modulus but also damping ratio from the IR test. However, the values of elastic modulus and damping ratio of concrete from the test is known to be affected by various test conditions including, specimen support condition, impact steel ball size and sampling rate. In this study, the optimum IR test conditions are suggested and validated experimentally. The test results showed that the recommended test conditions yielded a variation of resonant frequency within ${\pm}0.3%$ and damping ratio ${\pm}10.0%$. In addition, the modulus from the IR test was comparable to that from a static test when the effect of strain amplitude was properly taken into account.

• Journal of the Society of Disaster Information
• /
• v.16 no.1
• /
• pp.144-154
• /
• 2020

Purpose: This paper is a fundamental study on the applicability of the smart bolt developed for monitoring system to detect the leakage of water supply valve. Method: A leak detection experiments were conducted using the smart bolt having embedded strain sensors and accelerometer. The smart bolt used in study meets the allowable criteria of torque and tensile stress for water supply system, and it can be applied to a joint of the water supply valve by behaving well within the allowable limits. Result: As a result of the simulated leak tests, a leak signal at the valve leak point was detected in a band of 60Hz, and the main pipe leaking point was observed to produce a leak signal having much higher frequency than that of the valve leak point. This seems to result in a total coupled vibration under unconfined conditions of the pipes. Conclusion: The smart bolts appeared applicable to detecting a leaking signal from the water supply valve.