• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.503-506
• /
• 2008

본 연구에서는 하이드로포밍 공정을 적용한 엔진크레들 제품에 대해 최종 제품의 강도를 평가하고자 하였다. 먼저 적용 판재인 370과 440 소재에 대해 인장시험을 수행하여 소재의 경도와 강도의 상관관계를 분석하여 경도와 강도의 변환식을 도출하였다. 그런 다음 예비굽힘, 예비성형, 최종성형된 제품의 각 공정에 따른 유효변형률을 측정하고 같은 위치에서의 경도를 측정하였다. 측정된 경도는 앞서 도출한 경도와 강도의 변환식에 대입하여 각 공정을 마친 제품의 강도를 예측하고 결국 하이드로포밍된 엔진 크레들 제품의 유효변형률에 따른 강도를 예측식을 실험으로 도출하였다. 그 결과 예비굽힘, 예비성형, 최종성형을 마친 엔진 크레들 제품에 대해 유효변형률이 $24{\sim}72%$로 변하였고 이때 HF370의 경우에는 유동응력값이 $375{\sim}500MPa$로 증가하여 원소재에 비해 성형 후 $25{\sim}66%$의 강도증가량을 보였고, HF440의 경우에는 $470{\sim}565MPa$로 증가하여, 원소재에 비해 $17{\sim}41%$로 강도가 증가하는 것으로 나타났다. 그리고 이와 같은 변화값을 이용하여 유효변형률과 강도의 상관관계를 도출하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.76-85
• /
• 2017

In this study, to evaluate the mechanical properties of fiber-reinforced cement composites by strain rate, hydraulic rapid loading test system was developed. And compressive and tensile strength of the hooked steel fiber and polyamide fiber reinforced cement composite were evaluated. As a result, the compressive strength, strain capacity and elastic modulus were increased with increasing strain rate. The effect of compressive strength by type and volume fraction of fibers was not significant. The dynamic increase factor(DIF) of the compressive strength was higher than that of the CEB-FIP model code 2010 and showed a trend similar to that of ACI-349. The tensile strength and strain capacity were increased with increasing strain rate. The hooked steel fibers were drawn from the matrix. The tensile strength and strain capacity of hooked steel fiber reinforced cement composites were increased as the strain rate increased. The tensile strength and deformation capacity of the fiber reinforced cement composites were increased. And, hooked steel fibers were drawn from the matrix. On the other hand, because the bonding properties of polyamide fiber and matrix is large, polyamide fiber was cut-off with out pullout from matrix. The strain rate effect on the tensile properties of polyamide fiber reinforced cement composites was found to be strongly affected by the tensile strength of the fibers.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.726-736
• /
• 2003

Concrete columns confined with high-strength fiber composites can enhance its strength as well as maximum strain. In recent years, several equations have been developed to predict the behavior of the concrete columns confined with fiber composites. While the developed equations can predict the compressive strength of the confined columns with reasonable agreement, these equations are not successful in predicting the observed maximum strain of the columns. In this paper, a total of 61 test results is analysed to propose an equation to predict both compressive strength and maximum strain of concrete cylinders. The proposed equation takes into account the effects of confining pressure and cylinder size. Furthermore, in order to verify the proposed stress-strain curve for concrete cylinders, six cylindrical specimens were tested. Comparisons between the observed and calculated stress-strain curves of the tested cylinders showed reasonable agreement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.21-28
• /
• 2008

Stress-strain curves based on Ramberg-Osgood and Hollomon relations are strongly dependent upon the regressed range of strain. This work investigates mathematical expressions of true stress-strain curves of metallic materials. We first observe the variation of yield strength, strain hardening exponent and stress-strain curve with regressed range of stain. Based on sectional regression and expression using one or two parameters, we propose an optimal strain range for which yield strength and nonlinear material behavior are quite appropriate.

• Tunnel and Underground Space
• /
• v.20 no.2
• /
• pp.119-124
• /
• 2010

Hopkinson's effect tests were carried out for various strain rates on three different types of rock in both saturated and dry states in order to examine the effects of strain rate and water saturation on tensile strength. The tensile strength increased with the increase of the strain rate not only in dry state but also in saturated state. It was also especially recognizable that the dynamic tensile strength of rock in the dry state was proportional to approximately a one-third multiple of strain rate no matter what the type of rock. It was found that water saturation decreased tensile strength in the dry state of sandstone and tuff, both with high porosity, but no significant difference could be recognized between the dry and the saturated states of granite, which has a low porosity of 0.49%.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.12
• /
• pp.53-63
• /
• 2008

In this study, the cone tip resistances of cemented sand are measured by performing a series of miniature cone penetration tests in large calibration chamber, and the relations with constrained modulus, unconfined compressive strength, and shear strength of cemented sand are suggested. Experimental results show that both the cone tip resistance and constrained modulus of sand increase with increasing cementation effect as well as relative density and confining stress. However, it is observed that the relative density and confining stress have more significant influence on cone tip resistance than constrained modulus of cemented sand. Since the cone penetration into the ground induces the damage of cementation, the cone tip resistance can't properly reflect the cementation effect of sand. An analysis based on the constrained modulus shows that the measured cone tip resistance underestimates the deformation modulus of cemented sand by about $70{\sim}85%$. In addition, this study establishes various relationships among the above soil properties from the regression analysis.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.2
• /
• pp.83-93
• /
• 2012

Since reinforced soil walls were introduced in domestic civil engineering society in early 1980's, various reinforcing materials including metal strips, bar mats, and sheet-type reinforcement using geotextile, geogrid, and etc. have been developed for construction purpose. Especially, the geogrid has been mostly used as a reinforcement for reinforced earth structures. This paper describes the tensile behaviors of four types of domestic geogrids. Also, a series of the wide-width tensile tests on three types of geogrids were conducted to assess the reliability of the tensile strains in geogrid measured by strain gauge. The tensile strain by strain gauge is larger than real strain of the geogrid and a difference between strain gauge reading and real strain non-linearly increase with increasing the tensile strain. However, when the tensile strain is smaller than 3%, a difference between strain gauge reading and real strain is negligible.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.6
• /
• pp.207-216
• /
• 1997

본연구는 축방향 변형 구속이 고강도 콘크리트 휨부재의 휨 전단거동에 미치는 영향을 조사하기 위한 것으로, 수화열과 건조수축에 기인하는 축방향 변형과 재하에 의한 축방향 변형을 구속한 부재 및 무구속 부재에 대하여 휨파괴와 전단파괴 실험을 실시하였다. 타설 직후부터 축변형을 구속한 실험체의 재하시 강성은 재하전의 구속으로 발생한 관통균열의 영향을 받아 무구속 실험체의 강성보다 낮지만, 재하시의 축변형 구속에 따른 압축구속력의 상승으로 인하여 강성의 크기는 역전되었다 축변형이 완전히 구속된 휨부재의 휨강도는 무구속 부재보다 20%이상 상승하지만 변형능력은 감소하는 것으로 나타났으며, 재하전의 축변형 구속에 의한 관통균열(균열폭 0.1mm 미만)은 부재의 전단내력 및 전단균열 진전 형상에 영향을 미치지 않았다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.6
• /
• pp.91-97
• /
• 2016

Evaluation on the test of actual concrete member to confirm the fire resistance of the concrete member using ultra-high strength concrete is required. However, test equipment which has large loading capacity is needed to the actual member experiment. So, many researchers evaluated the fire performance through analytical studies using the material models. This study experimentally evaluated strain properties on ultra-high-strength concrete of 80, 130 and 180 MPa with heating and examined to apply the existing strain model about ultra-high-strength concrete. As a results, constants are drawn by method of least squares applying experimental values and calculated values by the existing strain model, it proposed strain model that can be applied to ultra-high-strength concrete.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.1
• /
• pp.17-23
• /
• 1990

When a thin walled member is subjected to compression in a condition such as collision, the energy is mainly absorbed by axial crumpling. In this case, dynamic crushing strength of the member is increased due to the effects of strain-rate compared with the static strength, even though the inertia effect is neglected. In this paper, the method of predicting the static crushing for tubular members is presented using the kinematic method of plasticity. Since, a predicted crushing load, taking account of the dynamic yield stress, usually overestimates the effects of strain-rate, the average plastic flow stress for the effects of strain-rate is used to obtain the dynamic crushing load for tubular members. The analytical results are compared with the experiments published in references, and a good correlation is observed.