• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.225-234
• /
• 2008

This study was carried out to select proper loading speed for deformation strength ($S_D$) of asphalt mixtures. Kim test using loading head of diameter(40mm) with radius(10mm) was conducted to measure $S_D$ in different loading speed (10mm/min, 30mm/min, 50mm/min, 70mm/min) and wheel tracking test was also conducted. The regression analyses between the So values and WT results were carried out by loading speeds. Higher $S_D$ was observed as increasing loading speed. This means that loading speed is a high influencing factor on $S_D$. The loading speed of 30mm/min was found as an optimum for better correlation with WT results than any other speeds from the regression analysis between $S_D$ and wheel tracking test results. $S_D$ value measured at other loading speed than 30mm/min has to apply the conversion coefficients.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.127-134
• /
• 2009

This study was performed to establish the process mean which is statistically satisfying the critical limit of deformation strength $(S_D)$, which is found to reflect rutting characteristics of asphalt mixture relatively well. The process means were determined using the critical $S_D$ values (3MPa for local highway and 4MPa for arterial highways), which were obtained from correlation analysis of APA and $S_D$ test data of actual highway projects, and coefficient of variation of 32 combinations of domestic mixtures. The process means of 3.2 MPa for local highway and 4.25 MPa for arterial highways were suggested when using 3 specimens (diameter of 100mm). However, since these values are based on the loading speed of 30mm/min, the higher values, 3.5 MPa for local highway and 4.5 MPa for arterial highways, were suggested, respectively, if the loading speed of 50mm/min is applied using the old Marshall machine, which should give higher test values.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2009

In general, it is well known fact that the stone mastic asphalt (SMA) pavement has a high resistance against rutting. However, performance of SMA is not well measured by general method used in the laboratory. The objective of this study is to investigate an applicability of deformation strength ($S_D$) for performance estimation of SMA, and to find out the correlation between rut depth and dynamic stability, and $S_D$ of SMA. This study carried out wheel tracking test and Kim-test with optimum asphalt content (OAC) determined by mix design. The results indicated that the $S_D$ of SMA was very poorer than those of dense-graded asphalt mixtures. $S_D$ showed similar WT dynamic stability and rut-depth level. It was found that Kim-test was not reflected higher rutting resistance of SMA like as indirect tensile strength (ITS) test and Marshall stability test. Also, it was revealed that dynamic stability and rut-depth of WT had some problems to estimate rutting resistance of SMA mixtures.

• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.627-636
• /
• 2011

Recently, to prevent explosive spalling of high-strength concrete (HSC) members, the usage of nylon fiber instead of polypropylene fiber has increased. Past experimental studies have been conducted to examine the spalling and mechanical properties of HSC with nylon fibers when exposed to elevated temperature. However, the previous studies on HSC with nylon fibers subjected to high temperatures were performed only on the properties such as spalling, compressive strength, and elastic modulus rather than investigations on to the behaviors such as thermal strain, total strain, steady state creep, and transient creep. Therefore, in this study thermal strain, total strain, steady state creep, and transient creep of HSC mixed with nylon fibers with water to binder ratio of 0.30 to 0.15 were tested. The experimental results showed that nylon fibers did not affect the performance of HSC with nylon fibers at high temperatures. However, HSC with nylon fibers generated a larger transient creep strain than that of HSC without fibers and normal strength concrete.

• The Korean Journal of Rheology
• /
• v.8 no.2
• /
• pp.129-138
• /
• 1996

접착강도는 접착제의 점탄성을 반영한 온도·속도 의존성을 나타낸다는 것이 잘 알 려져있다. 특히 유리전이온도(Tg)에서의 역학적 완화기구가 접착층의 변형을 수반하는 접착 층의 변형을 수반하는 접착강도에 크게 영향을 미치고 있다. 또한 접착계의 모드I의 변형에 너지 해방율(GIC)를 측정할때에도 접착제의 변형과 파괴가 발생하기 접착제의 점탄성이 그 값에 어떠한 영향을 미치는 지에 흥미가 깊다. 본 연구에서는 2종류의 에폭시 수지를 블랜 드한 접착제를 이용하여 일정한 측정조건에서 인장 접착강도와 GIC의 상관관계에 대하여서 도 토론하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.729-734
• /
• 1995

원자력용 316L강에 질소를 첨가한 경우의 고온 인장성질을 조사하였다. 온도가 증가하면 인장강도는 감소하다가 온도범위가 30$0^{\circ}C$~50$0^{\circ}C$에서는 일정한 값을 나타낸 후 급격한 감소를 나타내었고 연신율은 감소하다가 40$0^{\circ}C$에서 최소값을 나타낸 후 다시 증가하는 경향을 나타내었다. 질소를 첨가하면 인장강도증가와 함께 연신율도 증가하였다. 동적변형시효 온도구간에서 변형속도변화에 따른 인장강도 및 연신율의 변화는 매우 작다. 동적변형시효를 위한 활성화에너지를 구해본 결과 동적변형시효를 일으키는 원소는 Cr이다. 질소를 첨가하면 동적변형시효가 발생되는 온도가 고온 쪽으로 이동되었는데 이것은 질소가 Cr과의 상호작용에 의해 Cr의 확산속도를 낮추기 때문이다. 가공경화지수는 동적변형시효와 회복의 영향으로 40$0^{\circ}C$에서 최대값을 나타내었으며 이 온도는 연신율이 최소값을 나타내는 온도와 인장강도가 일정하게되는 온도와 일치하므로 강도강화기구는 동적변형시효로 판명되었다.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.197-206
• /
• 1997

본 연구에서는 기존의 초고강도 콘크리트에 대한 실험자료를 근거로 합리적인 통계적 기법을 이용하여 초고강도 콘크리트의 설계 실용화를 위한 응력-변형율 관계 모델과 응력분포 모델을 제안하는 것이 목적이다. 이를 위하여 첫째, 콘크리트의 응력-변형율 특성을 결정하는 재료 변수들(탄성계수, 최대 압축강도시 변형율 등)에 대한 검토를 수행하였다. 둘째, 이를 바탕으로 일반성과 정확성을 동시에 갖춘 초고강도 콘크리트(700~1400kg/$\textrm{cm}^2$)에 적합한 응력-변형율 모델을 제안, 비교, 고찰하엿다. 셋째, 제안된 응력-형율 모델로부터 초고강도 콘크리트 구조의 극한강도를 평가하기에 적합한 응력분포모델을 제안, 일반성과 정확성을 비교 검증하였다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.3
• /
• pp.35-44
• /
• 2000

전편의 실험적 연구에 이어서, 기 수행된 4개의 외부 접합부 시험체에 현존하는 여러 강도 예측식을 사용하여 콘크리트 기둥-강재 보 접합부의 내진 성능을 결정하는 패널 전단 및 지압 강도를 평가하였다. 또한, 접합부 패널지역의 변형특성을 묘사할 수 있는 일련의 스프링을 사용한 macro 형태의 해석모델이 논의되었으며, 이에 따라 Drain-2DX 및 IDARC 등의 상용프로그램을 사용하여 접합부의 패널전단 및 지압 파괴형태의 변형을 포함하는 단순해석이 수행되었다. 강도 예측결과에 의하면 본 연구에서 제시하는 수정된 내부 콘크리트 패널 전단 강도식을 포함하고 있는 ASCE 방법이 실험결과에 가장 근접한 것으로 나타났으며, 본 연구에서 검토된 패널지역 변형을 고려한 단순해석모델은 향후 전체 건물해석에 사용할수 있는 것으로 판단되었다.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.466-475
• /
• 2001

The potential shear strength of reinforced concrete beams decreases after flexural yielding due to the decrease of the effective compressive strength of concrete in plastic hinge zone. A truss model considering shear deterioration in the plastic hinge zone was proposed in order to evaluate the ductile capacity of reinforced concrete beams failing in shear after flexural yielding This model can determine the potential shear strength of the beam by using a truss model. The potential shear strength gradually decreases as the increase of the axial strain of member. When the calculated potential shear strength decreases up to the flexural yielding strength, the corresponding rotation angle is defined as the ductile capacity of the beam. The predicted ductile capacity of reinforced concrete beams is shown to be in a good agreement with experimental results.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.183-191
• /
• 2008

This study evaluated influence of the loading head dimension on characteristics of deformation strength ($S_D$) of asphalt mixtures. Kim test and Wheel tracking (WT) test were conducted to evaluate $S_D$ characteristics with relation to WT results for various mixtures. The $S_D$ values and coefficient of variation of $S_D$ values of r=10mm were smaller than those of r=10.5mm. It was also found that $S_D$ values obtained using r=10mm loading head showed high correlations with rut parameters of WT test. It was indicated that the aggregate size and radius (r) of round cut were statistically significant variables on $S_D$ at = 0.05 level in the analysis of variance. However, in interaction of r and aggregate size showed no significance within $10{\sim}19mm$ aggregate size at the same level. Therefore, it was concluded that the diameter (D) of 40mm and the bottom edge radius (r) of 10mm was suitable dimension of loading head for deformation strength test.