• The Journal of the Korea Contents Association
• /
• v.15 no.2
• /
• pp.499-506
• /
• 2015

The friction velocity is a quantity with the dimensions of velocity defined by the friction stress and density of a wall surface at near wall of flow condition. Also, the friction velocity is the hydraulic parameter describing shear force at the bottom flow. Moreover, it is a very important factor in designing open channel and essential to determine the mixing coefficient in the main flow direction. The estimation of the friction velocity are such as methods using channel slope, linear law of the mean velocity at viscous sub-layer and direct measurement of wall shear stress, etc. In the present study, we propose a friction velocity equation that has been optimized by combining the concept of entropy, which is used in stochastic method, and to verify the proposed equation, the experimental data measured by Song was used. The R squared for friction velocities between proposed equation and friction velocity formula analyzed 0.999 to 1.000 in a very good agreement with each equation.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.2
• /
• pp.120-124
• /
• 1991

An interaction of turbulent boundary layer and local roughness effects was evaluated to investigate the shear frictional coefficient in diffuser. Clauser roughness function was applied to Karman's integral equation for governing equation. The roughness of overall and local diffuser surfaces were calculated using Cole's wall and wake law and Clauser's roughness function for turbulent boundary layer characteristics. The calculating results were compared with the experimental results of other paper. It shows some significant improyements for shear frictional coefficient. Computer code was then used to confirm the behavior of local frictional coefficient along with diffuser roughness surface for some reduction of shear flow stress.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.355-362
• /
• 2016

The pipe material is selected according to the physical and chemical properties of the fluid flowing within it. Because the fluid used in fire extinguish systems is water, the various foreign substances dissolved in it cause scale to form on the pipe wall and accelerate the corrosion and aging of the pipe itself. This results in an increase in the friction loss and eventually degrades the efficiency of the pump. The use of CPVC (Chlorinated Poly-Vinyl Chloride) pipes was confirmed to reduce the friction loss compared to conventional steel pipes in the design and construction stages. The friction loss was found to be 76.64MPa with a C-value of 120 for the steel pipe and 50.72 MPa with a C-value of 150 for the CPVC pipe in an actual apartment construction environment. It was confirmed that the friction loss was improved by about 34% when using the CPVC pipe. When the steel and CPVC pipes were employed in the construction, the construction costs were 1,585,158 and 931,842 won, respectively. Therefore, it was shown that the construction cost was reduced by about 41%. We investigated the safety of the fire extinguishing system and the improvement in the economic performance due to the reduction in the total installed capacity by studying practical applications in the field.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1717-1726
• /
• 1991

본 연구에서는 낮은 레이놀즈수 영역에도 적용될 수 있는 레이놀즈응력모델의 개발을 위해, 우선 벽근처 영역에서 사용되는 실험식(벽법칙)을 Hassid와 Poreh에 의 해 개발된 1-방정식모델로 대체하고 이를 레이놀즈응력모델과 접속시키는 방식을 사용 하였다. Hassid-Poreh의 1-방정식모델은 이미 Gibson등에 의해 그 성능이 평가되어 압력구배가 크지 않은 경계층유동의 낮은 레이놀즈수 영역에서 매우 좋은 결과를 보여 줌이 밝혀졌다. 본 연구에서는 곡면위의 난류경계층에 대해 위에서 설명한 바 있는 난류모델을 적용함에 있어 Gillis등과 Gibson등에 의해 실험된, 각각 곡률이 큰 경우 와 작은 경우의 대표적인 유동을 선택하여 모델의 성능을 시험하였다. 1-방정식모델 내에 포함된 길이차원(length scale)에 대해서는 곡률을 고려한 수정이 이루어졌다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.240-250
• /
• 1995

A CPM (computational preston tube method) was developed to measure wall shear stress in a transitional boundary layer on a flat plate using Preston tubes. Correlation for the displacement factor of Preston tubes was improved for a CPM to be used in the transitional boundary layer. The distribution of skin-friction coefficient was reasonably predicted in the uniform free stream of 3.1% turbulence intensity. Reasonable and accurate estimation of displacement factor of Preston tubes was found to be of crucial importance for the CPM, especially in the laminar boundary layer. The mean velocity profiles of the boundary layer on the plate were also measured and presented.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.952-961
• /
• 1989

The purpose of this study is to investigate the behavior of operational and design factors on the performance characteristics of a horizontal fin-tube heat exchanger under phase change conditions for refrigerant. The flow and heat transfer in the heat exchanger are simulated numerically taking into account the variations of heat transfer coefficients, thermodynamic and flow properties of refrigerant, and the axial heat conduction in the tube wall. As the results of this study, it was found that the annular flow model was more reasonable physically than the homogeneous one for the two phase flow of refrigerant and axial heat conduction of tube wall did not have a great influence on the analysis. The effects of refrigerant pressure, mass flow rate of air, diameter of tube and the number of fins per unit length of tube were also discussed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.11
• /
• pp.1055-1063
• /
• 2012

Fluctuating wall pressures were measured using an array of 16 piezoelectric transducers beneath a turbulent boundary layer. The coating used in this experiment was an open-cell, urethane-type foam with a porosity of approximately 50 ppi. The ultimate objective of the coating is to provide a mechanical filter to reduce the wall pressure fluctuations. The boundary layer on the flat plate was measured by using a hot wire probe, and the CPM method was used to determine the skin friction coefficient. The wall pressure autospectra and streamwise wavenumber-frequency spectra were compared to assess the attenuation of the wall pressure field by the coating. The coating is shown to attenuate the convective wall pressure energy. However, the relatively rough surface of the coating in this investigation resulted in a higher mean wall shear stress, thicker boundary layer, and higher low-frequency wall pressure spectral levels compared to a smooth wall.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.168-168
• /
• 2015

자연하천의 주요한 특징 중 하나인 하천의 사행은 직선수로에서 예측되는 유속분포를 왜곡시키며 매우 복잡한 흐름구조를 형성한다. 이는 하상 경계면에서 발생하는 전단응력 분포의 변화를 야기하는데 하상 경계면에서의 전단응력은 다양한 경험적 관계에 의존하는 유사이동의 한계 소류력 산정 및 오염물질 거동해석의 분산계수 산정에 많은 영향을 미치게 된다. 물리적인 관측을 통한 하상 경계면에서의 전단응력의 관측은 다소 제한적이며 많은 비용을 요구한다. 따라서 하상 경계면에서 발생하는 전단응력의 경우 수심의 20% 이하의 연직 유속분포를 벽법칙에 적용하여 추정하는 방법이 주로 이루어지고 있다. 벽법칙을 이용한 하상 경계면의 전단응력을 계산하는 경우 대수중복층의 유속 분포 $u/u^*=(1/{\kappa})ln(zu^*/{\nu})+B$에서 무차원상수 ${\kappa}$와 B의 적절한 추정이 요구되어 진다. 일반적으로 무차원상수 ${\kappa}$와 B는 수리학적으로 매끄러운 벽면에서 대략 ${\kappa}=0.4$, B=5.5로서 경험적으로 이용되고 있다. 본 연구에서는 직선수로 및 다양한 사행수로의 3차원 흐름장 모의를 수행하여 벽법칙의 대수 중복층을 따르는 주흐름 방향 유속의 연직분포를 비교하였다. 수치모의 소프트웨어로서 Linux 기반의 OpenFOAM이 사용되었으며 모델의 검증을 위해 Chang(1971)에 의해 수행 된 사행수로에서의 유속장 관측 결과와 비교하였고 수치모의 결과가 실험 관측치와 잘 일치하는 것으로 판단되었다. 수치모의에 적용 된 사행수로의 형상은 Hey(1976)에 의해 제안 된 사행하천의 지형학적 인자들 간에 관계를 이용하여 사행도 1.03에서 2.42까지 총 7개의 사행수로 지형을 생성하였다. 사행도의 변화에 따라 만곡부 정점에서 대수중복층 구간의 주흐름 방향 유속의 연직분포를 비교한 결과, 본 연구에서 생성 된 모든 사행수로에서 대수중복층 구간의 무차원 유속 $u^+$와 무차원 거리 $z^+$가 로그 분포를 따르는 것으로 나타났으나 경험적으로 사용되었던 무차원상수 B의 경우 사행도가 증가 할수록 대수적으로 감소하는 경향이 나타났다. 본 연구에서는 이러한 관계가 무차원 상수 B값에 미치는 영향을 반영하여 수리학적으로 매끄러운 벽면에서 적용이 가능한 수정된 대수중복층 식을 제시하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1335-1348
• /
• 1998

Flow characteristics in transitional boundary layers on a flat plate were experimentally investigated under three different freestream conditions i. e. uniform flow with 0.1 % and 3.7% freestream turbulent intensity and cylinder-wake with 3.7% maximum turbulent intensity. Instantaneous streamwise velocities in laminar, transitional and turbulent boundary layers were measured by I-type hot-wire probe. For estimation of wall shear stresses on the flat plate, measured mean velocities near the wall were applied to the principle of Computational Preston Tube Method (CPM). Distributions of skin friction coefficients were reasonably predicted in all developed boundary layers. Intermittency profiles, which were estimated using Conditional Sampling Technique in transitional boundary layers, were also consistent with previously published data. It was predicted that the incoming turbulent intensity had more influence on transition onset point and transition process than freestream turbulent intensity existed just over the transition region. It was also confirmed that non-turbulent and turbulent profiles in transitional boundary layers could not be simply treated as Blasius and fully turbulent profiles.

• Tribology and Lubricants
• /
• v.30 no.5
• /
• pp.278-283
• /
• 2014

Carbon nanotubes (CNTs) are used in various composite materials to enhance electrical, thermal and mechanical properties of composite materials. In this study, we investigate the wear characteristics of polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) blends containing multi-walled carbon nanotubes (MWCNTs). PC/ABS blends are commonly used in many industrial applications such as cellular phones and display cases and MWCNTs have been added to the PC/ABS blends to improve their electromagnetic interference shielding (EMS). We performed wear tests on PC/ABS blends containing MWCNTs under reciprocating linear sliding conditions with chrome steel balls as a counterpart material. The normal loads were 10, 30, 50, 70, 100 N, the sliding speed was 10 mm/s, the stroke length was 15 mm, and the tests lasted 900 s. The MWCNTs included in the PC/ABS blends lower the wear volume and friction coefficient of the composites. We analyzed the wear debris collected from the composites during the tests in terms of the MWCNT concentration using inductively coupled plasma optical emission spectroscopy. The results show that the quantity of MWCNTs in the debris is proportional to the concentration of MWCNTs in the composite, indicating that the exposure of the MWCNTs to environments by wear could be increased with their concentration in the composite.