• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1282-1291
• /
• 1989

본 연구에서는 이러한 연구의 시작단계로 노즐내의 열 경계층 방정식을 정리하고 압축성 와점도모델을 도입하여 유한 차분법을 이용한 전산프로그램을 작성 하였다. 한편 실제로 추진모테에서는 고온 고속의 열기류가 분출되기 때문에 추진 하고 있는 동안 노즐벽을 형성하고 있는 내열재가 심하게 손상되어 표면의 상태가 매우 거칠게 된다. 더구나 경우에 따라서는 내열재가 용발(ablation)하게 된다. 이러한 상태를 감안하여 마찰계수와 열전달 계수를 합리적으로 추정해야만 노즐의 설계와 주변장치를 합리적으로 수행할 수 있다. 따라서 본 연구에는 주로 경계층 내의 압력구배, 압축성의 효과, 물성치의 변화를 고려한 기존 난류모델에 근거하여 프로그램을 작성하고, 이것을 토대로 노즐표면 조도의 영향 및 분출(blowing)의 영 향을 중점적으로 고려하여 그 특성을 연구하였다. 노즐벽에서 분출을 고려한 이유는 표면이 용발할 때 표면의 온도가 거의 일정하게 유지된 상태로 노즐표면이 화학작용을 수반하면서 가스화됨을 초보적으로 고려해보기 위함이다.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.96.2-96.2
• /
• 2010

본류부에서 지류부로 유입되는 흐름의 내측 벽면에는 토사나 오염물의 퇴적물침전이 발생하게 된다. 이는 개수로 분류흐름의 특성으로 인하여 이차류 흐름이 나타나는 분리구역이 발생하기 때문이다. 수치모의를 실행하여 Hsu 등(2002)과 Ramamurthy 등 (2007)의 분류흐름 수로의 결과값과 수치모의를 통한 결과를 비교하여 신뢰성이 높음을 알 수 있었다. 본 연구에서는, 분류흐름에서 발생하는 분리구역을 줄이기 위해 분류가 시작되는 본류의 수로의 크기 조절을 통하여 분리구역의 크기를 줄였다. 또한 변형으론 인한 분리구역을 줄이기 위해 본류와 지류가 만나는 모서리 지점을 곡선과 대각선으로 연결하여 유수흐름을 완만하게 만든 지형들을 제안하였다.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.13 no.1
• /
• pp.14-21
• /
• 1984

The purpose of this investigation is to study heat transfer characteristics in wall jet region on a flat plate caused by upward impinging water jet. In the wall jet region, heat transfer results by impinging water jet are being compared with the ones with supplementary water. As the radius increases, the heat transfer coefficient in the wall jet region consquently decreases, but decreasing nozzle-heat plate distance, the reduction rate increases. The experimental equation is expressed as follows : $$\frac{N_{ur}}{P_r^{0.4}}{\cdot}\overline{\xi}=m(\overline{\eta}{\codt}Re{\delta})^n,\;m=0.034\~0.056,\;n=1.74\~2.007$$ The optimum height of supplementary water is obtained to improve heat transfer effect of wall jet region.

• Journal of Energy Engineering
• /
• v.11 no.3
• /
• pp.276-282
• /
• 2002

The process of energy separation in a low Pressure vortex tube with compressed air as a work-ing medium is studied in detail. Experimental data of the temperature of the cold and hot air leaving the vortex tube are presented. The variation of the maximum wall temperature along the inner surface of the vortex tube and the temperature distribution in a vortex tube provide useful information about the location of the stagnation point of the flow field at the axis of the vortex tube. Analysis of the results enabled to find the optimum length of the vortex tube, the optimum shape of the Throttle and the usefulness of the Sleeve. In this study Outer tube is used for the exhaust application. The hot gas flow is turned 180$^{\circ}$and passes the out-side of the vortex tube a second time heating it. From this geometric setup of a vortex tube He effects of energy separation and the prediction of the ignition of Diesel Soot is presented by experimental data.

• Solar Energy
• /
• v.17 no.1
• /
• pp.47-58
• /
• 1997

The objective of this research was to investigate the enhancement of heat transfer by wire mesh in impinging air jet system at the potential core region. The first experiment was carried out without mesh between nozzle exit and flat plate and the second experiment was done with mesh between them. When mesh was installed in front of the plate, heat transfer has been Increased due to the acceleration between rectangular halls and divided small jet In case clearances are changed, heat transfer comes to maximum under the condition of C=1mm, irrespective of nozzle exit velocity and H/B. Also the average heat transfer enhancement rate of a flat plate with mesh has been increased about 44% at maximum under the condition of U=18m/s, H/B=2 and C=1mm, compared to the result of a flat plate without mesh.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.7
• /
• pp.457-470
• /
• 2016

Most CFD codes, that mainly adopt the heat partitioning model as the wall boiling model, have shown low accuracies in predicting the two-phase flow parameters of subcooled boiling phenomena under low pressure conditions. In this study, a number of subcooled boiling experiments in vertical channels were analyzed using a thermal-hydraulic component code, CUPID. The prediction of the void fraction distribution using the CUPID code agreed well with experimental data at high-pressure conditions; whereas at low-pressure conditions, the predicted void fraction deviated considerably from measured ones. Sensitivity tests were performed on the submodels for major parameters in the heat partitioning model to find the optimized sets of empirical correlations suitable for low-pressure subcooled flow boiling. The effect of the K-factor on the void fraction distribution was also evaluated.

• Tunnel and Underground Space
• /
• v.10 no.4
• /
• pp.497-505
• /
• 2000

The surveyed area is mainly distributed by the sedimentary rocks, tuffs, and esites in Cretaceous age and acidic and basic dikes are intruded in these rocks. The principle discontinuities are represented by beddings, joints and faults. The trends of the beddings of sedimentary rocks develop as E-W direction in the start area. However, they are gradually bending and finally their trends are N-S direction in terminal area. In the sedimentary rocks the 3∼4 joint sets are distributed and in dikes joints are more scattered. The majority of joints are highly dipped. Sampo fault which has NE-SW trend makes a valley and NW trending normal faults are well developed at 50k+600 to 51k+000 area. During the construction of tunnel the orientation of discontinuities will not significantly influence on the stability of excavation. Since the rock mass is extensively jointed, the overbreak in tunnel wall may be placed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.485-492
• /
• 2013

The effect on collection efficiency with 2-stage vortex finder diameter and back mixing of solid flow due to swirling intensity, turbulence eddies, wall bouncing using the residence time distribution of particle flow in a common and modified cyclone. Higher collection efficiencies of fly ash in a modified cyclone(S = 13, 15cm) are showed than common cyclone. Collection efficiency in modified cyclone was highest at 2-stage vortex finder diameter, S = 13 cm. Variances of residence time distribution and average residence times of glass bead were increased with a diameter(S) of 2-stage vortex finder due to swirling intensity and turbulence eddies. Back mixing of solid flow in a modified cyclone were increased with a gas inlet velocity and showed higher than a common cyclone.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.12
• /
• pp.107-116
• /
• 2011

Rigid soil containers (or rigid boxes) are often used for 1g shaking table tests. The rigid boxes, however, do not accurately simulate the amplification of ground acceleration and phase difference of seismic motion in the model ground due to the confinement of shear deformation and the reflection of seismic wave at the box walls. Laminar soil containers (or laminar shear boxes) can simulate the free field motion at convincingly superior accuracy than the rigid ones. In this study, the soft ground is modeled for both types of boxes and is subjected to seismic loading using a 1g shaking table. The comparison of the results using the two types of soil containers illustrates that, in case of the rigid box, the ground acceleration shows non uniform distribution and the phase synchronization of input motion. Whereas, the dynamic behavior of the laminar shear box shows good agreement with the free field behaviors such as the amplification of ground acceleration and the occurrence of phase difference.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.15 no.2
• /
• pp.136-146
• /
• 2007

Landfill leachate was successfully treated in upflow anaerobic sludge blanket (UASB) reactors regardless of the addition of granular sludge. Initial operating period was significantly reduced by the addition of granular sludge. At hydraulic retention time (HRT) of one day, chemical oxygen demand (COD) removal rates in Control and Granule reactor were maintained over 90%, respectively with organic loading rate (OLR) of $4-8kgCOD/m^3.d$. During the experiment, the inorganic precipitates were accumulated in and around the sludge, and in the wall of the reactors were formed in both reactors regardless of addition of granular sludge. Specific methanogenic activity (SMA) increased as adaptation of microorganism to the substrate and OLR were increased. The maximum SMA value of the sludge for Granule reactor was about $0.57gCOD/g{\cdot}VSS{\cdot}.d$. The SMA value was not decreased because of excessive inorganic accumulation, however, it was needed to have pre-treatment process of influent to remove the inorganic metals.