• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.3
• /
• pp.97-105
• /
• 1997

The aim of this paper is to introduce a design technique of the Two-Degree-of-Freedom(TDF) satellite-tracking control system which has not only the robust stability for a unstructured uncertainty but also the robust performance for a structured uncertainty. This TDF system which can design the feedforward controller KI and the feedback one K independently is designed by , $\mu$-synthesis. The effectiveness of this TDF system is verified and compared with the One-Degree-of -Freedom(ODF) satellitetracking control system by computer simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.89-97
• /
• 2003

High frequency common mode voltage produced by PWM inverter fed Induction motor is a major cause of conducted EMI, creation motor ground currents, bearing currents and other harmful products. The zero switching states of inverter control invoke large in comparison with the non-zero switching state of Inverter control. We proposed a common mode voltage reduction method based on sinusoidal PWM technique. PWM signal are generated by comparing respective sinusoidal reference signal with three triangular carrier wave displaced of 120$^{\circ}$. Simulation and experimenta1 result show that common mode voltages in the proposed PWM technique are reduced by approximate 66% more than conventional FWM technique.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.158-162
• /
• 2004

The magnetic levitator is the device which can float a magnetic material at the midair by electromagnetic force and it's principle can be applied to the high speed magnetic bearing or magnetic levitation train. There are many difficulties to control, because the magnetic levitator is basically a nonlinear and unstable system. In this paper, this system is modeled assuming that it is a linear system nearby an operating point, and a proportional and derivative(PD) position controller is designed to carry out the variable position control. The performance of position control response is shown through simulation and experiment. A prototype magnetic levitator is constructed using PWM converter and DSP(Digital Signal Processor) based control board.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.814-820
• /
• 2020

In the M-ary DCSK system up to now, as M increases, the distance between constellation signal points becomes closer and performance deteriorates. we propose a hybrid modulation scheme based on PPM and DCSK to improve the BER performance. one part of the bit is modulated by the PPM and the other part by DCSK. Thus, the information bearing signal is modulated simultaneously according to the selected pulse position of the PPM determined by the information bit and the additional information bit. The analytical BER performance of the proposed plan is derived and verified by simulation. The results show that the proposed scheme outperforms conventional M-DCSK, code index modulation DCSK and rectified code index DCSK in additional white Gaussian noise and multipath Rayleigh fading channels.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.270-281
• /
• 2017

In this paper, a vibratory disturbance to the rotor system generated by gyroscopic precession through helicopter rotor is examined. Also, active vibration reduction method is designed and simulated by designing feedback controller. For this purpose, structural analysis is carried out using EDISON's geometric exact beam program which can analyze the rotor with the cantilever condition. And the aeroelastic analysis is performed by coupling it with the simple aerodynamic model. In order to obtain the real-time structural response, the EDISON program analysis results were modeled by nonlinear equations and the Newton-Raphson method was used for the trim analysis.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.1-7
• /
• 2013

In this study, simulation on the powder compression forming of oilless bearing is performed and the analysis results are compared with the actual products. This study aims to examine the suitability of powder compression for bearing by using FEA(finite element analysis) before full-scale production. The lubrication state can be predicted by changing the coefficient of friction in order to get the optimal density gradient. Analysis for single and double action presses are performed and these results are compared with each other. State and process of optimal lubrication are proposed from the study result.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.362-372
• /
• 1989

It is important in design of vertical pumps to consider external excitation in addition to rotor vibration due to unbalance. In this study, a model of a vertical pump was developed for the analysis of its dynamic response. The vertical pump was modeled with lumped masses and springs which represent multi-cylindrical and rotor structure. A dynamic simulation program was developed and numerical calculation on the above mentioned problems were carried out.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.507-515
• /
• 2004

With the advent of fast power devices, the high dv/dt voltage produced by PWM inverts have been found to cause EMI noise, shaft voltage and bearing current. This paper describes the application of newly developed Conducted EMI reduction SVPWM technique in induction motor drives. The newly developed common mode voltage reduction SVPWM technique don't use any zero-vector states for inverter control, hence it can restrict the common mode voltage more than conventional PWM technique. The validity of the proposed technique by software approach is verified through simulation and experimental results.

• Tribology and Lubricants
• /
• v.35 no.4
• /
• pp.244-266
• /
• 2019

The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.

• Tribology and Lubricants
• /
• v.28 no.2
• /
• pp.47-55
• /
• 2012

Generally, to product multi-grade oil like engine oil, a sort of mineral base oil is mixed with a fundamental additive package liquid and a polymer liquid as viscosity index improver in order to improve the lubricating property of base oil. That is, engine oil is the mixture of more than two fluids. Specially, a polymeric type liquid cannot be seen as the linear viscosity like Newtonian fluids. In this research, by using the governing equation describing non-Newtonian hydrodynamic lubrication related with the mixture of incompressible fluids based on the principle of continuum mechanics, it will be compared the bearing performance between the mixture of each liquid to be blended and multi-grade engine oil as a single fluid in a high speed hydrodynamic journal bearing. Further, it is to be found the way estimating the performance of the blended multi-grade engine lubricant in a journal bearing in advance before blending by using the physical properties of mineral base oil, fundamental additive liquid and polymer liquid of viscosity index improver. So, it can be reduced the number of trial and error to get the wanted lubricant by selecting the proper volume fraction of each liquid to satisfy the expected performance and estimating in advance the performance of various multi-grade oils before blending. Therefore, it can be shorten the developing time and saved the developing cost.