• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.70-78
• /
• 2011

The Equations of inherent flow coefficient are different from compressible to incompressible flow. The paper has been conducted to measure the inherent flow coefficient of solenoid valve under various flows. Experimental results for compressible and incompressible flow were confirmed to inherent flow coefficient correctly. The value of inherent flow coefficient for the 0.5" solenoid valve is about 2. Dynamic characteristics of a solenoid valve, which plays an important role in real model, have been analysed by AMESim simulator modeling.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.995-999
• /
• 2017

The factors affecting the flow coefficient of a control valve were identified and analyzed. The flow coefficient of a control valve are affected by not only Reynolds Number but also the figure and the roughness of the inlet/outlet pipes. Therefore, the flow coefficient is not a constant value. For the purpose of use in the system such as LRE, requiring the exact flow-coefficient of a control valve, the flow-coefficient should be measured under similar Reynolds Number using the inlet and outlet pipes which have the same figure and roughness with a real system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.89-95
• /
• 2017

The improvement of a flow coefficient for the recirculation chill-down flow in a main oxidizer shut-off valve has been presented. The flow coefficient, which is mainly affected by the recirculation outlet port size and the configuration inside the valve, has been predicted with measured flow coefficient values. The comparison of experimentally measured flow coefficient with the predicted value shows the effect of valve inside configuration on the flow coefficient. Consequently, the flow coefficient is twice the previous value and about 75% of the pressure loss assigned to the main oxidizer shut-off valve can be used for additional pressure losses for other components in the recirculation chill-down system of a launch vehicle.

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.140-148
• /
• 2009

MOV(Main Oxidizer shut-off Valves) control the combustion of launch vehicle systems by the supply and the isolation of liquid oxygen to a main combustion chamber in launch vehicle systems. Moreover, in the steady operational state, the MOV should secure a constant flow rate of liquid oxygen for combustion instability in the combustion chamber. Concerning the development of MOV, TM(Technology Model) has been manufactured and normal operations of the valve have been verified. However, the Cv of TM has been proved to be too low as compared with a design specification value. Therefore, CFD analysis have been performed by modification of the configurations of TM in order to increase sufficiently Cv of EM(Engineering Model), which is the following model of TM. The modifications of TM configurations such as partial scale-up of valve, increase of stroke length, and outlet angle of 120o would result in a considerable augmentation of Cv. It has been verified by flow capacity tests that the improved Cv of EM is min. 212, which is higher than Cv of TM, 161 by about 32%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.423-429
• /
• 2012

Miller cycle is considered as an effective means to meet the regulation on Tier II and to reduce $CO_2$ emission. For this cycle, the amount of intake air supplied should be enough increased. Therefore, the intake system with minimized resistance for air flow is under consideration. In this study, the flow coefficients of intake valves were measured in order to obtain the basic data for the cycle simulation and intake port design. The flow coefficients were measured using the steady-flow test rig. As a test result for the poppet valve used the marine engine with medium speed, the flow coefficients are increased to about 0.62 with the valve lift. In addition it is confirmed that the flow coefficients have the characteristic value irrelevant to the S/B ratio.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.487-494
• /
• 1995

원자력발전소의 안전성 향상을 목적으로 신형원자로 안전주입계통의 축압기 설계에 적용이 고려되고 있는 피동적 유량조절 장치인 vortex 밸브의 유동장을 해석하여 밸브의 특성에 영향을 미치는 주요 인자들을 도출하고 이 인자들의 영향을 분석하였다. 분석 결과 Vortex 밸브의 성능 특성은 수송유량, 제어유량, chamber의 반경, 입구면적, 마찰계수 등의 영향을 받는 것으로 나타났으며 이들 인자 중 chamber의 반경의 영향이 가장 크고 Reynolds수의 영향은 비교적 작은 것으로 파악되었다. 또한 주어진 유동조건에서 제어유량이 작은 경우 점성손실이 vortex 밸브의 유동특성에 미치는 영향이 증대되는 경향을 보였으며 유량이 증가할수록 Reynolds수의 영향은 감소하는 것으로 나타났다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.734-739
• /
• 2016

The globe valve is a linear motion valve that is designed primarily to stop, start, and regulate flow. The disk of a globe valve can be removed totally from the flow path or it can completely close the flow path. In this study, numerical analysis using ANSYS-CFX was initially performed to predict the flow coefficient and build a prototype model of a globe valve. The flow coefficient is the volume of water at $15.6^{\circ}C$ that will flow per minute through a valve with a pressure drop of 1 psi across the valve. In other words, it is an important factor for determining the size of the valve. From the analysis results, the fluid flux of water and flow coefficient of the valve were extracted. From the numerical results, a prototype of ultra-fine precision control valve, which can regulate the fluid flow of range 0 ~ 0.1 gal per min, was developed. The experimental results were compared with the numerical results using the flow coefficient ($C_v$) graph. From the comparative results, the flow coefficient ($C_v$) error percentage between the numerical and experimental results was very low, which is acceptable, proving that the proposed prototype model is convincing. In addition, it is possible to predict the flow coefficient using only numerical analysis.

• Journal of Navigation and Port Research
• /
• v.31 no.1 s.117
• /
• pp.49-53
• /
• 2007

The valve is used on control of flow in a ship. Flow coefficient of valve is very importance in the design of valve. In this paper, three-dimensional computer simulations by commercial code CFX were conducted to observe the valve type and to measure flow coefficient when valves with various angles and uniform incoming velocity were used in a piping system. By contrast, a group of experimental data is used to compare with the data obtained by CFX simulation to investigate the validity of numerical method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.387-392
• /
• 2020

This paper proposes a flow-rate control system for industrial valves. Industrial valves are used in piping systems to control the flow rate and pressure. In general, valves used in pipelines are classified into globe valves, butterfly valves, and ball valves according to the shape. Motor, hydraulic, and pneumatic systems are used for operating valves. The flow meter should measure the flow rate when configuring the flow-rate control system. On the other hand, because the flow rate of the valve can be expressed by flow coefficient, a control scheme is proposed using the pressure deviation, which measures at the front and rear of the valve. The transfer function for the valve, according to the control input, was estimated using the signal compression method. Based on the induced transfer function, the disturbance observer was designed to improve the command following the performance of the valve stem. The performance of the proposed control method is compared with the flow-rate control result using the flow meter used.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.122-128
• /
• 2012

Many of the liquid rocket engines use a hypergolic igniter with rupture disc ends located in the combustion chamber ignition line. In this study, the flow coefficient tests of the igniter, which have a solenoid valve upstream, were performed. The tension-type rupture discs for radial and circumferential scores and the igniter with them were tested using water at room temperature. The effects of the score, flow rate, the disc thickness, gas pocket and the solenoid valve on the coefficient were analyzed.