• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6C
• /
• pp.251-258
• /
• 2009

In this study, the optimum design conditions for embankment construction on soft clay layer improved by soil compaction pile (SCP) are discussed by comparing the practical design method to the reliability design which is based on the loss function and advanced first order second moment (AFOSM) method. The results are summarized as follows; 1) the relationship between safety factor and failure probability becomes heavy exponentially, failure probability decreases rapidly till 1% approximately until safety factor is smaller than 1.2 and after then, failure probability decrease gradually along the increase of the safety factor. The design safety factor of 1.2 may be the critical value that has been established on considering both relationships appropriately, 2) the safety factor of 1.15 at the minimum expected total cost is a little smaller than the design safety factor of 1.2 and the failure probability is about 1%, 3) the sensitivities of the ratio of stress share and the internal friction angle of sand is larger than the variables related the undrained shear strength of soft layer. This result means that the distribution characteristic of n and ${\phi}$ influences on the stability analysis considerably and they should be considered necessarily on stability analysis of embankment on soft layer improved by SCP, 4) new failure points of the input variables at the design safety factor of 1.2(below failure probability of 0.1~0.3%) is far 1~2 times of standard deviation from the initial design values of themselves.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.4
• /
• pp.73-82
• /
• 2023

In this study, the optimal method for injection of neutralizer to restraint the leakage of acid drainage in embankment structure composed of pyrite rocks is proposed. Finite Element Analysis was performed to examine the seepage effect caused by injection of neutralizer into the embankment structure. The diameter of the neutralizer injection hole was selected as 50cm, the interval space of injection ranged from 1m to 4m and the injecting pressure ranged from 100kPa to 220 kPa were applied for the numerical analysis. According to the analysis results, the saturation time of the whole embankment structure was shown to be fast at a relatively low injecting pressure in the case of injecting interval space of 1.0m and injecting pressure of 130kPa and in the case of injecting interval space of 2.0m and injecting pressure of 160kPa. When the interval space of injection for saturation of whole embankment structure is selected as 3m, various injection pressures can be applied from 130kPa to 190kPa, and the saturation time of whole embankment is similar regardless of the injection pressure. Therefore, the optimal method for injection of neutralizer considering economic efficiency was selected as injecting interval space of 3.0m and injection pressure of 130kPa.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.56-63
• /
• 2023

In this paper, we studied the effect of electron beam irradiation on sol-gel indium-gallium-zinc oxide (IGZO) thin films under air and nitrogen atmosphere and carried out the electrical characterization of the s ol-gel IGZO thin film transistors (TFTs). To investigate the optical properties, crystalline structure and chemical state of the sol-gel IGZO thin films after electron beam irradiation, UV-Visible spectroscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) were carried out. The sol-gel IGZO thin films exhibited over 80% transmittance in the visible range. The XRD analysis confirmed the amorphous nature of the sol-gel IGZO films regardless of electron beam irradiation. When electron beam irradiation was conducted in a nitrogen (N₂) atmosphere, we observed an increased proportion of peaks related to M-O bonding contributed to the improved quality of the thin films. Sol-gel IGZO TFTs subjected to electron beam exposure in a nitrogen atmosphere exhibited enhanced electrical characteristics in terms of on/off ratio and electron mobility. In addition, the electrical parameters of the transistor (on/off ratio, threshold voltage, electron mobility, subthreshold swing) remained relatively stable over time, indicating that the electron beam exposure process in a nitrogen atmosphere could enhance the reliability of IGZO-based thin-film transistors in the fabrication of sol-gel processed TFTs.

• Korean Journal of Environmental Agriculture
• /
• v.29 no.1
• /
• pp.20-26
• /
• 2010

This study was conducted to reclassify Donggui series based on the second edition of Soil Taxonomy and to discuss the formation of Donggui series in Jeju Island. Morphological properties of typifying pedon of Donggui series were investigated and physico-chemical properties were analyzed according to Soil survey laboratory methods manual. The typifying pedon has very dark grayish brown (10YR 3/2) silt loam A horizon (0~17 cm), gravelly very dark grayish brown (10YR 3/2) silt loam BA horizon (17~42 cm), gravelly very dark grayish brown (10YR 3/2) silty clay loam Bt1 horizon (43~80 cm), brown (7.5YR 4/6) silty clay Bt2 horizon (80~105 cm), and brown (10YR 5/4) silty clay Bt3 horizon (105~150 cm). It is developed in lava plain and are derived from basalt and pyroclastic materials. The typifying pedon contains 1.3~2.1% oxalate extractable (Al + 1/2 Fe), less than 85% phosphate retention, and higher bulk density than 0.90 $Mg/m^3$. That can not be classified as Andisol. But it has an argillic horizon from a depth of 22 to 150 cm and a base saturation (sum of cations) of less than 35% at 125 cm below the upper boundary of the argillic horizon. That can be classified as Ultisol, not as Andisol and Inceptisol. It has udic soil moisture regime, and can be classified as Udalf. Also that meets the requirements of Typic Hapludalf. It has 18-35% clay at the particle-size control section, and have thermic soil temperature regime. Therefore Donggui series can be classified as fine loamy, mixed, thermic family of Typic Hapludalfs, not as fine silty, mixed, thermic family of Dystric Eutrudepts.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.2
• /
• pp.224-229
• /
• 2010

This study was conducted to reclassify Cheongpung series based on the second edition of Soil Taxonomy, and to dicuss the formation of Cheongpung series distributed on the diluvial terrace. Morphological properties of typifying pedon of Cheongpung series were investigated, and physico-chemical properties were analyzed according to Soil survey laboratory methods manual. The typifying pedon of Cheongpung series has red (2.5YR 4/6) silty clay loam Ap horizon (0-18 cm), red (2.5YR 4/8) clay BAt horizon (18-35 cm), red (2.5YR 4/2) cobbly clay Bt1 horizon (35-65 cm), and red (2.5YR4/6) cobbly clay Bt2 horizon (more than 65 cm). The typifying pedon has an argillic horizon from adepth of 18 to more than 65 cm, and a base saturation (sum of cations) of less than 35% at 125 cm below the upper boundary of the argillic horizon. It can be classified as Ultisol, not as Alfisol. It has udic soil moisture regime, and can be classified as Udult. Also that meets the requirements of Typic Hapludults. It has 35% or more clay at the particle-size control section, and have mesic soil temperature regime. Therefore Cheongpung series can be classified as fine, mesic family of Typic Hapludults, not as fine, mesic family of Ultic Hapludalfs. Cheongpung series occur on moderately elevated diluvial terrace which have relatively stable geomorphic surface. They are developed as Ultisols with clay mineral weathering, translocation of clays to accumulate in an argillic horizon, and leaching of base-forming cations from the profile for relatively long periods under humid, and temperate climates in Korea.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.4
• /
• pp.237-245
• /
• 2014

Amur silver grass (Miscanthus sacchariflorus) and reed canary grass (Phalaris arundinacea) were selected for RDX removal experiments in hydroponic culture conditions based on vegetation survey at three shooting ranges in northern Kyunggi province. Seedling of two plants were grown in 1/4 strength Hoagland solution in quadruplicates containing 10, 20, 30, 40 mg/L RDX for 15 days along with control and blank treatments. During the 15 days of incubation, pH and RDX concentration in medium were routinely analyzed and RDX contents in the shoot and the root were determined after solvent extraction at the end of the experiments. Both plant species showed no symptoms of RDX phyto-toxicity. The pseudo first order RDX-removal constants for amur silver grass and reed canary grass were in the range of $0.0143{\sim}0.0484day^{-1}$ and $0.0971{\sim}0.1853^{-1}$, respectively. Plant biomass normalized RDX removal rates, which decreased with the increase of initial RDX concentration, were in the range of $0.27{\sim}1.01mL{\cdot}g^{-1}day^{-1}$ and $0.87{\sim}1.66mL{\cdot}g^{-1}day^{-1}$ for amur silver grass and reed canary grass, respectively. After 15 days of treatment, RDX removal from the medium decreased from 49.0% to 23.7% with increase in the initial RDX concentration in amur silver grass and 7.3% of the initial RDX remained in the plant. In reed canary grass planted medium, less than 16.8% and 5% of the initial RDX remained in the medium and in the plant, respectively. Large quantities of unidentified polar compound, which was not detected in amur silver grass, accumulated in the root and shoot of reed silver grass.

• Journal of Plant Biotechnology
• /
• v.41 no.3
• /
• pp.116-122
• /
• 2014

Total of fifty accessions of Brassica rapa with various morphological characteristics were used for production of double haploid plants though microspore culture in Brassica rapa. Among them, only 30 accessions induced embryos from microspores. The highest efficiency of embryo induction of 1.194 per bud was obtained from IT135449 of turnip type, while 3 accessions of sarson (winter oil) type did not generate embryo. The effect of heat shock periods for embryogenesis was also investigated with 4 accessions (IT135449; Turnip type, IT199710; Chinese cabbage type, IT212886; Pak choi type, IT218043; Summer oil type). The high productions of embryos were observed in IT135449, IT199710 and IT212886 when microspores were pre-cultured to $32^{\circ}C$ for 2 days. In IT218043, high embryogenesis was observed at the 3 days of heat shock treatment. The optimal condition of shoot regeneration for IT199710 was observed in MS medium supplemented with NAA $0.5mg{\cdot}L^{-1}$ and BAP $1mg{\cdot}L^{-1}$. In contrast, the IT135449 and IT212886 were observed high regeneration frequency in MS medium without plant growth regulators. All the plantlets regenerated from microspore-derived embryos have been successfully transplanted to soil, and bud self-pollinated seeds were produced from doubled haploid plants. This indicated that double-haploid genotype was likely generated naturally during embryogenesis process.

• Food Science of Animal Resources
• /
• v.23 no.4
• /
• pp.333-341
• /
• 2003

The effect of water extract of Schizandra chinensis on the growth of yoghurt starter was investigated in order to manufacture the drink type yoghurt added with water extract of Schizandra chinensis. It was the most desirable extraction conditions for Schizandra chinensis to soak in 50 times of water for 15 hours at 20$^{\circ}C$. The water extract of Schizandra chinensis showed pH 3.07, 2.39％ acidity, 1.10％ total sugars, and 0.15 optical density for color. The water extract of Schizandra chinensis was added to MRS broth medium from 0.1％ to 1.0％ and the medium was fermented by 4 types of lactic acid bacteria such as Lactobacillus acidophilus, Lactobacillus casei, Lactobacillus bulgaricus, and Streptococcus thermophilus. The addition of water extract of Schizandra chinensis inhibited the growth of the lactic acid bacteria. The maximum addition amounts of water extract of Schizandra chinensis was 0.9％ for Lac. acidophilus, 0.8％ for Lac. casei, 0.2％ for Lac. bulgaricus and 0.1％ for Str. thermophilus in order to maintain the propagation of the lactic acid bacteria. When the drink type yoghurts added with 0.4％, 0.6％, 0.8％ and 1.0％ water extract of Schizandra chinensis were kept at 4$^{\circ}C$ for 15 days, it was showed that the number of lactic acid bacteria was not significantly changed during the storage. The viable cell counts of the drink type yoghurts by addition of 0.4∼l.0％ of water extract of Schizandra chinensis were 1.13${\times}$10$\^$9/∼2.29${\times}$10$\^$9/ CFU/mL, and these bacterial counts were still more than the legal standard(1.0${\times}$10$\^$8/ CFU/mL) even at 15 days of storage.

• Clean Technology
• /
• v.17 no.4
• /
• pp.306-313
• /
• 2011

Flux or solder is used in soldering process for manufacturing electronic parts such as printed circuit boards (PCB). After soldering process, residual flux and solder paste on the parts should be removed since their residuals could cause performance degradation or failure of parts due to their corrosion and electric leakage. Ozone depletion substances such as 1,1,1- trichloroethane (TCE) and HCFC-141b have widely been using for removal of residual flux and solder paste after soldering process In manufacturing of electronic parts until now. In this study, non-aqueous cleaning agents without flash point were developed and applied to industrial field for replacement of cleaning agents with ozone depletion. In order to develop non-aqueous cleaning agents without ethers, esters, fluoride- type solvents. And their physical properties and cleaning abilities were evaluated, and they were applied to industrial fields for cleaning of flux and solder on the PCB. And vacuum distillation apparatus were operated to determine their operating conditions and recycling yields for recycling of used cleaning agents formulated in this study. As a result of physical properties measurement of our formulated cleaning agents, they were expected to have good wetting and penetrating power since their surface tensions were relatively low as 18.0~20.4 dyne/$cm^2$ and their wetting indices are relatively large. And some cleaning agents holding fluoride-type solvents as their components did not have any flash point and they seemed to be safe in their handling and storage. The cleaning experimental results showed that some cleaning agents were better in their cleaning of flux and solder paste than 1,1,1-TCE and HCFC-141b. And industrial application results of the formulated cleaning agents for cleaning PCB indicated that they can be applicable to industry due to their good cleaning capability in comparison with HCFC-141b. The recycling experiments of the used formulated cleaning agents through a vacuum distillation apparatus also showed that their 91.9~97.5% could be recycled with its proper operating conditions.

• Korean Journal of Environmental Biology
• /
• v.40 no.3
• /
• pp.267-274
• /
• 2022

Excess nitrogen (N) flowing from livestock manure to water systems poses a serious threat to the natural environment. Thus, livestock wastewater management has recently drawn attention to this related field. This study first attempted to obtain the optimal conditions for the further volatilization of NH₃ gas generated from pig wastewater by adjusting the amount of injected magnesia (MgO). At 0.8 wt.% of MgO (by pig wastewater weight), the volatility rate of NH₃ increased to 75.5% after a day of aeration compared to untreated samples (pig wastewater itself). This phenomenon was attributed to increases in the pH of pig wastewater as MgO dissolved in it, increasing the volatilization efficiency of NH₃. The initial pH of pig wastewater was 8.4, and the pH was 9.2 when MgO was added up to 0.8 wt.%. Second, the residual ammonia nitrogen (NH₄⁺-N) in pig wastewater was removed by precipitation in the form of struvite (NH₄MgPO₄·6H₂O) by adjusting the pH after adding MgO and H₃PO₄. Struvite produced in the pig wastewater was identified by field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) analysis. White precipitates began to form at pH 6, and the higher the pH, the lower the concentration of NH₄⁺-N in pig wastewater. Of the total 86.1% of NH₄⁺-N removed, 62.4% was achieved at pH 6, which was the highest removal rate. Furthermore, how struvite changes with pH was investigated. Under conditions of pH 11 or higher, the synthesized struvite was completely decomposed. The yield of struvite in the precipitate was determined to be between 68% and 84% through a variety of analyses.