• Journal of the Korean Institute of Gas
• /
• v.23 no.3
• /
• pp.1-6
• /
• 2019

The purpose of the present study is to elucidate flue gas recirculation device for reduction of nitrogen oxides using coanda nozzle without adopting additional power driving fan in a waste incinerator. The characteristics of the exhaust gas recirculation flow rate and the average temperature change at the outlet of the mixed gas were investigated according to the change of air supply nozzle gap and the position of air supply nozzle. When the gap of the air supply nozzle was changed to 3.22, 4.03, and 4.84 mm, the largest recirculation flow ratio, which is the ratio of exhaust gas recirculation flow rate and air supply flow rate, was 2.227 for the case with 3.22 mm and its mean temperature at outlet was $594.8^{\circ}C$. When the position of the air supply nozzle changes to the front position, neck position, and expansion position of the coanda nozzle neck, the recirculation flow ratios at the forward position and the neck position were nearly almost the same value, 1.843, and 1.696 at the expansion position, their mean temperatures were $559.8^{\circ}C$ and $544.3^{\circ}C$, respectively.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.22-29
• /
• 1990

• Journal of the Korea Organic Resources Recycling Association
• /
• v.7 no.2
• /
• pp.93-104
• /
• 1999

Existing composting system was improved to have a high performance for organic degradation, deodorization and energy reduction. Compared with conventional devices, this developed system uses the heat recovered from platinum catalytic tower by three times heat exchange in which 65% of exhaust gas was recirculated. Evaporation of water was made easy by maintaining negative pressure in entire system. It was possible for reaction to be maintained steadily by microorganism agent. The optimum mixing volume ratio of garbage to sawdust was 15:1 contrary to 20:1 in conventional one. Moreover, aerobic condition was maintained efficiently. Effects obtained by using a inner circulation system were as follows. It was possible to reduce the ammonia causing offensive odor and verified that consumption of electricity cut down to 1/3 with reduction of exhaust gas inflowing. According to this inner circulation, the optimum air flow was $0.44m^3$ to 100kg treatment capacity. The electricity consumption was changed in proportion to inflowing air volume.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.2
• /
• pp.189-195
• /
• 2020

In this study, the inlet duct and guide vane of the gas floating absorption tower were redesigned to improve the desulfurization efficiency so that the exhaust gas can be uniformly introduced into the absorption tower. In order to reduce the sulfur oxide pollutants among the main sources of air pollutants in industrial boilers, the existing equipment is redesigned and solved. For this purpose, change the exhaust gas, the slurry and recycling the adsorbent to improve the removal efficiency of SOx component in the exhaust gas inside the gas floating absorption tower so as to uniformly contact. And the initial design value and CFD value for the pressure loss from the boiler outlet to the gas floating absorption tower outlet are verified. Also, the velocity distribution of the exhaust gas, the concentration distribution of the recycled adsorbent, the liquid slurry behavior, and the pressure loss were compared. The results confirmed that the desulfurization efficiency was improved because the pressure loss from the boiler outlet to the absorption tower outlet was reduced and the deflection of the exhaust gas was minimized.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.112-117
• /
• 2007

With the Euro-4 regulation coming into effect, the domestic car industry is forced to look for newer options to reduce NOX in the exhaust. EGR(Exhaust Gas Recirculation) Cooler is an effective method for the reduction of NOX form a diesel engine. High efficiency, low pressure loss and compactness are desirable features of an EGR Cooler. The cooling performance of EGR depends on the shape of tubes and the location of the entrance and exit. This paper reports the computational work conducted to estimate the performance of EGR cooler with three different cross section tubes and a triangular spiral tube. Three dimensional computation results show that the triangular tube is more effective than circular and rectangular tube. The most effective geometry is a triangular spiral tube with offset inlet and outlet locations.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.6
• /
• pp.577-583
• /
• 2011

To meet the requirements of the Tier 4 interim regulations for off-road vehicles, emissions of particulate matter (PM) and nitrogen oxides (NOx) must be reduced by 95% and 30%, respectively, compared to current regulations. In this research, both the DPF and HPL EGR systems were investigated, with the aim of decreasing the PM and NOx emissions of a 56-kW off-road vehicle. The results of the experiments show that the DOC-DPF system is very useful for reducing PM emissions. It is also found that the back pressure is acceptable, and the rate of power loss is less than 5%. By applying the HPL EGR system to the diesel engine, the NOx emissions under low- and middle-load conditions are reduced effectively because of the high differential pressure between the turbocharger inlet and the intake manifold. The NOx emissions can be decreased by increasing the EGR rate, but total hydrocarbon (THC) emission increases because of the increased fuel consumption needed to compensate for the power loss caused by EGR and DPF.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.247-252
• /
• 1997

최근 자동차 배기 가스에 대한 규제가 강화되고 있고, 특히 자동차 매연중 대젤 차량에 대한 배기 가스 저감이 관심의 대상이 되고 있다. 이러한 배기 가스 규제에 대응하기 위하여 엔진의 여러 부위에 대한 설계변경이 이루어지고 있다. 설계변경의 대표적인 예로는 피스톤 탑 링(top piston ring)의 위치를 현재보다 위로 하고 피스톤과 라이너 사이의 간극을 좁게하여 크레비스 볼륨을 줄이거나, 연로 분사 시기 지연, 배기가스재순환(EGR, Exhaust Gas Recirculation)장치 등이 있다. 본 보고에서는 모사 실험 결과에 추가하여 엔진 시험을 수행함으로써 엔진유의 분산 특성및 산화안정성에 미치는 기유와 첨가제의 영향을 조사하였다.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1203-1205
• /
• 1987

가솔린 엔진용 전자 제어 에뮬레이션 시스템은 엔진의 운전 상태를 알려 주는 각종 센서로 감지한 정보를 A/D변환기를 통해 마이크로프로세서에 입력시키고, 이 정보를 이용하여 운전 상태를 분석한 후 엔진이 푤요로 하는 연료량, 점화시기, 배기가스의 재순환량, 공회전수 등을 전자적으로 제어하여 엔진의 최적제어를 실현시킴으로서 연료소비율 및 배기가스 중 공해물질 함량을 감소시키기 위한 장치이다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.159-164
• /
• 2009

Cooled EGR system is an effective method for the reduction of $NO_x$ emission and PM emission from a diesel engine. Proper choice of wavy cooling fins and gas tubes is a key factor of cooled EGR system. As a part of solutions for energy crisis and environmental problems, hybrid vehicles mounted with diesel engines are under development globally. This study investigates the cooled EGR systems for hybrid diesel engine with the specifications of both optimized wavy cooling fins and improved shape of structure to verify the heat exchange efficiency, outlet temperature and gas pressure drop of cooler by means of numerical analyses and rig performance tests. The output of this study will be applied to a 2.0L hybrid diesel engine which is being developed for domestic and overseas market.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.89-94
• /
• 2011

The EGR system is one of important components in diesel engine. The regulation on NOx emission has been tightened up. Therefore, it is a significant issue to develop and commercialize the high efficient EGR cooler system that reduces NOx emission in DI diesel engine. Key performance factor of the EGR cooler system is how to properly design both wavy cooling fins and gas tubes. This paper proposes a high efficient EGR cooler that has been upgraded with both the optimized wavy cooling fins and the improved shape of structure. The evaluation of the heat exchange efficiency, outlet temperature, and gas pressure drop of the EGR cooler is performed with the prototype of the proposed EGR cooler. The result shows a good solution and will be implemented to the model of a clean diesel engine being developed for both domestic and overseas market.