• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.560-560
• /
• 2013

플라즈마 내의 전자 에너지 분포는 방전 특성 및 전자 가열 메커니즘에 대한 정보를 줄 수 있을 뿐만 아니라, 소자 생산 공정에서 공정 조건 제어 및 소자 품질 향상에 중요한 역할을 하는 변수이다. 그에 따라서, 반도체공정에서 널리 쓰이는 유도 결합 플라즈마 또는 용량성 결합 플라즈마 장치의 외부 변수에 따른 전자 에너지 분포 변화에 대한 연구가 많이 진행되어왔다. 본 연구에서는, 극판 전극이 인가된 유도 결합 플라즈마 구조에서 낮은 압력의 아르곤과 산소 기체 방전에 대하여 전자 에너지 분포를 측정하였다. 극판 전압만이 인가되었을 경우에는 두 개의 온도를 갖는 전자 에너지 분포를 측정하였으나, 소량의 안테나 전력을 인가할 경우 하나의 온도를 갖는 전자 에너지 분포를 측정할 수 있었다. 이러한 분포함수의 급격한 변화는 유도 결합 전기장과 용량성 결합 전기장의 혼재에 따른 전자 가열 효과이며, 극판에서의 전압, 전류 그리고 위상 측정을 통하여 전자 가열 메커니즘을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.619-620
• /
• 2015

본 논문은 독립형 마이크로그리드 환경에서의 신재생에너지원의 출력 안정화 및 디젤발전기의 최소 사용을 통한 경제적인 운영을 위해 필요한 ESS(Energy Storage System)의 도입을 위한 용량 산정 및 SOC에 따른 충/방전 알고리즘을 제안한다. 제안한 산정 알고리즘을 통해 도서지역의 독립형 마이크로그리드의 데이터를 활용하여 ESS 용량을 산정하고, 이에 대한 효과를 검증한다.

• Korean Chemical Engineering Research
• /
• v.61 no.1
• /
• pp.39-44
• /
• 2023

In this study, the particle size of Si polycrystals was controlled through wet-sedimentation method, and changes in the capacity and cyclic characteristics of the Si anode material according to the particle size were observed. After wet-sedimentation of Si particles pulverized by a vibration mill, the non-uniform particle distribution of Si was uniformly controlled. The d₅₀ of a sample in which Si was sedimented for 24 hours decreased to 0.50 ㎛. As a result of the electrochemical characteristic analysis, the Rct value representing the resistance in the electrode was significantly reduced due to the decrease in particle size. The unclassified Si sample exhibited a discharge capacity of 2,869 mAh/g in the first cycle, and decreased to 85.7 mAh/g after 100 cycles. The sample in which Si was classified for 24 hours showed a capacity of 3,394 mAh/g initially, and maintained a capacity of 1,726 mAh/g after 100 cycles. As the size of the Si particles decreased, the discharge capacity increased and the cycle life was also increased.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.1
• /
• pp.46-49
• /
• 1999

Lithium cobalt oxide cathode for thin-film rechargeable lithium batteries were fablicated by electron-beam evaporation. Annealed lithium cobalt oxide, which was deposited on to stainless steel substrate, showed well-developed (003) planes of the hexagonal structure and potential plateau at $\~3.9 V$. Lithium cobalt oxide thin films had the stoichiometric Li/co ratio at high deposition rates and exhibited high discharge capacity at $15{\AA}/s$. As the annealing temperature increased, discharge capacity increased with maximum value at $700^{\circ}C$, but showed low capacity as a result of reaction with substrate above $700^{\circ}C$. Unuiformity of the lithium and cobalt in the depth profile gave initial capacity loss with charge/discharge performance.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.1-8
• /
• 2019

In this paper, the electrical characteristics with various C-rates are tested with a high power series battery pack comprised of 18650 cylindrical nickel cobalt aluminum(NCA) lithium-ion battery. The electrical characteristics of discharge capacity test with 14S1P battery pack and electric vehicle (EV) cycle test with 4S1P battery pack are compared and analyzed by the various of C-rates. Multiple linear regression is used to estimate voltage imbalance of 14S1P and 4S1P battery packs with various C-rates based on experimental data. The estimation accuracy is evaluated by root mean square error(RMSE) to validate multiple linear regression. The result of this paper is contributed that to use for estimating the voltage imbalance of discharge capacity test with 14S1P battery pack using multiple linear regression better than to use the voltage imbalance of EV cycle with 4S1P battery pack.

• Journal of IKEEE
• /
• v.28 no.1
• /
• pp.14-19
• /
• 2024

To determine the performance of recycled cells for application to residential BESS, cells used over the past 5 years were selected. The basic specifications of the cell used in the test are nominal voltage of 3.7[V], nominal capacity of 2,200[mAh], charging voltage of 4.05[V], continuous discharge current of 1[C](2,200[mA]), continuous charging current of 0.5[C](1,100[mA]). For new cells, the internal resistance was 21.3±1[mΩ], but for recycled cells, the average internal resistance was 25.38[mΩ], an increase of about 19.1[%]. The charge·discharge capacity was approximately 18.9~19.3[%] lower than that of a new cell. Because internal resistance and charge·discharge capacity are closely related to cell aging, cells to be applied to BESS need to use products with an initial internal resistance of 1.5 times or less and a charge·discharge capacity performance of 70[%] or more.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.4
• /
• pp.222-229
• /
• 2012

We studied the electrochemical phenomena and increase of capacity according to the polymer composite electrode of two different polymeric materials with different the voltage range and capacity. Polyaniline (PANI) with relatively high voltage and small capacity and poly [1,2] bis-thio[1,8]-naphthylidine (PTND) with slightly low voltage and large capacity were used as polymer composite electrode materials. After PTND was synthesized, PANI was synthesized on the surface of PTND. The synthesis and the fine structure were analyzed by FT-IR, XPS, FE-SEM, and FE-TEM. Charge/discharge capacity and cyclic voltammetry measurements were carried out for the electrochemical performance as a polymer cathode active material for lithium secondary batteries. The discharge capacities of PANI/PTND after 1,5, and 10 cycles at 1.3~4.0 V voltage range and room temperature 167 mAh/g, 90 mAh/g, and 81 mAh/g. When we compared with PANI (80, 67, and 62 mAh/g), the discharge capacity after 10 cycles was improved about 30%. After 50 cycles, the discharge capacity of PANI/PTND was 67 mAh/g.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.125-129
• /
• 2008

Rechargeable lithium-ion polymer batteries have been considered to be next-generation power sources for portable electronic devices and electric vehicles. In this work, we tried to improve the cycling performances of lithium-ion polymer cells by coating aluminum fluoride and acrylonitrile-methyl methacrylate copolymer to the polyethylene separator. It was found that the addition of aluminum fluoride to the surface-modified separator reduced the interfacial resistances and thus the cell exhibited a less capacity fading and better high rate performance. The cell showed an initial discharge capacity of 150 mAh/g and good capacity retention at 0.5 C rate.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.69-74
• /
• 1999

Graphite and carbonaceous materials intercalate and deintercalate Li-ion reversibly into their layered structures. These materials show an excellent capacity for using a negative electrode in Li-ion batteries, because the electrochemical potential of Li-ion intercalated carbon is almost identical with that of lithium metal. Carbon used in this study was obtained by the pyrolysis of petroleum pitch, and heat-treated at the several temperatures between $700^{\circ}C$ and $1300^{\circ}C$. XRD analysis revealed that crystallization of carbon increased with increasing the heat treatment temperature. Charge/discharge properties were studied by a constant-current step at the rate of 0.1C, and the interfacial reaction between the electrolyte and the surface of carbon electrode was studied by cyclic voltammetry. Cell capacities were investigated in terms of the heat treatment temperature and the cycle number. Reversible capacity increased with the heat treatment temperature up to $1000^{\circ}C$, thereafter decreased continuously. Also, charge capacity decreased with the cycle number, while the reversibility improved with it.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.113-114
• /
• 2011

납축전지는 충/방전을 반복함에 따라 전지 내의 화학적인 반응에 의해 그 용량을 잃어버린다. 그러한 과정에서 전지의 용량과 수명을 정확히 평가할 수 있도록 전지를 모델링하는 것이 이 논문의 목적이다. 정적 모델링을 통해 골프카트용 납축전지의 충/방전 특성의 연구 내용을 기술하였다. 정적 모델링 기법은 구성이 비교적 간단하고 결과를 빠르게 예측할 수 있는 장점이 있다. 이 모델링 기법을 통해 전지의 특성을 나타내는 변수들을 도출해내었다. 이러한 과정을 바탕으로 골프카트용 납축전지를 모델링한 후, 시뮬레이션 결과를 실험 데이터와 비교하여 모델링의 정확성을 판단하였다.