• Journal of the Mineralogical Society of Korea
• /
• v.28 no.2
• /
• pp.147-163
• /
• 2015

Chemical and mineralogical properties of coal ash samples from the nine thermal power plants of Korea were investigated to acquire basic data for estimating the potential of rare metal recovery. Chemical compositions of coal ash were consistent with those of average shale and foreign coal ashes. However, there were small differences between the metal contents of domestic anthracitic and imported bituminous coal ashes. Unburned coal particles were much abundant in the ash of domestic anthracitic coal. Chalcophile elements were relatively enriched in the fly ash compared to bottom ash. Silicate glass was the major component of coal ash with minor minerals such as quartz, illite (muscovite), mullite, magnetite, lime, and anhydrite. Al and Si were the major components of the glass with varying contents of Ca, Fe, K, and Mg. Glass occurred in a form of porous sphere and irregular pumace-like grain often fused with iron oxide spheres or other glass grains. Iron oxide spheres were fine intergrowth of fast-grown iron oxide crystals in the matrix of silicate glass. Chemical, microstructural, and mineralogical properties would guide successful rare metal recovery from coal ash.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.6
• /
• pp.497-503
• /
• 2016

Flue gas desulfurization gypsum is produced from emission process of fossil fuel power plant to remove sulfur dioxide ($SO_2$) from exhaust gas. Production of flue gas desulfurization gypsum in Republic of Korea has been increasing due to the enforced regulations by government agency. Since flue gas desulfurization gypsum has characteristic that is similar to that of natural gypsum, there is a strong possibility for flue gas desulfurization gypsum to replace the role of natural gypsum. However, consumption of such material is still limited, only used for agricultural purposes or to make gypsum boards, it is necessary to expand the use of this material more aggressively. In this research, the chemical and mineralogical properties of flue gas desulfurization gypsum were investigated, and flue gas desulfurization gypsum with heat treatment was used to make cement paste. According to the results, it was found that flue gas desulfurization gypsum used in this experiment was a very high purity gypsum, and shown to have similar property to that of natural gypsum. Heat treating flue gas desulfurization gypsum above $100^{\circ}C$ was shown to bring beneficial effect on both compressive strength and drying shrinkage

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.4
• /
• pp.61-74
• /
• 2012

Industrial complexes in Korea have been vigorously established by economic development plan and development policy of industry in 1960s. Recently, Korean government has promoted Eco Industrial Park (EIP) project to recycle by-products and wastes in industrial park In this study, we analyzed the physical and chemical properties for the sludges discharged from A industrial complex. And we investigated the economic feasibility and environmental impact of sludge to energy facilities. The analysis results indicated that the petrochemical industry were 92% in sludge production, the highest treatment amount was landfill, followed by incineration and recycling and then ocean disposal. Wastewater sludge and process sludge samples are collected and analyzed to use as basic data on economic feasibility and environmental impact. Weighted average heating value of sludge samples was 3,891kcal/kg. Based on this data, installation and operation costs, operation returns of operating the drying facility are estimated, compared with cogeneration facility. And this study examines how the payback period of each simulation(total 8 case) with the important parameter changes. As a result, it was found that what needs the shortest payback period is 3years with connection of drying facility and cogeneration facility based on the government's financial subsidy system.

• Resources Recycling
• /
• v.31 no.3
• /
• pp.40-52
• /
• 2022

This study analyzed the amount of carbon dioxide reduction and economic benefits of detailed processes of CO₂ 6,000 tons plant facilities with mineral carbonation technology using carbon dioxide and coal materials emitted from domestic circulating fluidized bed combustion power plants. Coal ash reacted with carbon dioxide through carbon mineralization facilities is produced as a complex carbonate and used as a construction material, accompanied by a greenhouse gas reduction. In addition, it is possible to generate profits from the sales of complex carbonates and carbon credits produced in the process. The actual carbon dioxide reduction per ton of complex carbonate production was calculated as 45.8 kgCO₂eq, and the annual carbon dioxide reduction was calculated as 805.3 tonCO₂, and the benefit-cost ratio (B/C Ratio) is 1.04, the internal rate return (IRR) is 10.65 % and the net present value (NPV) is KRW 24,713,465 won, which is considered economical. Carbon mineralization technology is one of the best solutions to reduce carbon dioxide considering future carbon dioxide reduction and economic potential.

• Clean Technology
• /
• v.7 no.1
• /
• pp.81-88
• /
• 2001

Limestone has been used as absorbent in the FGD(Flue Gas Desulfurization) system, the DeSOx system of thermal power plant. This study investigated the desulfurization characteristics of the two different limestones, 325mesh and 200mesh particle size. Experimental analysis showed that the dissolving rate of limestone became much slower as the particle size increased. But the desulfurization efficiency depended on the L/G(liquid/gas) ratio and slurry pH regardless of the limestone particle size. The quality of gypsum produced in the FGD process increased as the limestone particle size or the slurry pH decreased. To reduce the cost of absorbent, the mixed limestone which were composed of 200 and 325mesh limestone with 5 different ratios were tested.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.6
• /
• pp.553-559
• /
• 2015

In this study, to suggest the application method of recycled fine aggregate, the non-cement mortar was prepared and studied with the binders of blast furnace slag, fly ash, and fly ash from combined heat power plant. As a basic experiment, a series of tests was conducted to determine the potions of the binders and types of activator. When the binder was consisted with 20% of fly ash and 40% of fly ash from combined heat power plant, the highest strength of the mortar was obtained, and as an activator, the combination of sodium hydroxide 2.5%, and calcium hydroxide 7.5% showed the highest strength of the mortar. Therefore, this study focuses on engineering properties of mortar contains fly ash from combined heat power plant and recycled fine aggregate according to replacement ratio of recycled fine aggregate based on the optimum mix from the basic experiment. As a result, the best replacement ratio of recycled fine aggregate is 75%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.3
• /
• pp.129-135
• /
• 2011

EAF dust from steel industry used as primary materials for the production of lightweight aggregates. Fe compounds in EAF dust plays an important role in the bloating reaction. This study was conducted to evaluate the feasibility of using bottom ash and dredged soil from coal power plant and EAF dust. The effect of different raw material compositions and sintering temperatures on the lightweight aggregate properties were evaluated. The characteristic of thermal bloating of bottom ash and dredged soil were mainly influenced by ferrous materials. The specific gravity of aggregate was decreased with the addition of EAF dust and kerosene was reduced sintering temperature on the bloating formation. Lightweight aggregate containing 10% EAF dust having apparent density under 1.0 g/$cm^3$ were produced at $1150{\sim}1200^{\circ}C$.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.3
• /
• pp.305-312
• /
• 2017

This paper presents a laboratory investigation into the effects of fillers using industrial by-product such as coal ash, IGCC slag on properties of hot-mixed asphalt concrete variation with filler content. For comparison, existing mixture with lime and dust have also been considered. Marshall and flow test has been considered for the purpose of mix design as well as evaluation of mixture. Other performance tests such as indirect tensile strength test, tensile strength ratio(moisture susceptibility), dynamic stability have also been carried out variation with filler content. It is observed that the mixes with industrial by-product exhibit conform with quality standard. Therefore, it has been recommended to utilize industrial by-product based on fly ash wherever available, not only reducing the produce cost but also partly solve the industrial by-product utilization and disposal problem.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.197-197
• /
• 2011

최근 들어 전력 사용량의 증가로 인한 화력발전소의 부산물인 석탄회 중 바텀애시와 각종 공공사업과 관련하여 해마다 현장발생토의 발생량이 지속적으로 증가하고 있는 추세이다. 바텀애시와 현장발생토사를 효과적으로 재활용하는 방법 중 유동성 뒤채움재를 개발하여 활용하는 방안을 모색하기 위한 연구이다. SP로 분류된 흙 현장발생토와 서천 화력발전소에서 발생하는 석탄회 중 입경이 0.9~1.5mm의 바텀애시만을 선별하여 현장발생토와 바텀애시의 비율을 7 : 3으로 변환한 최적배합을 선정하여 강재로 제작된 가로 80cm, 세로 60cm, 높이 90cm의 모형토조를 이용하여 실험을 진행하였으며, 사용상 지하 매설이 되는 관의 거동 특성은 확인하기 위하여 내경 30cm, 두께 8mm의 연선관 중 하나인 PVC관을 원형지하매설관으로 선정하여 배합을 타설하는 과정과 타설 후 7일간의 양생기간을 거친 후 차량하중으로 가정할 수 있는 하중을 가하여 원형지하매설관의 관외부에서 수직방향과 수평방향의 토압과 관내부의 수직 수평방향 변위 그리고 관 자체의 횡 종단 변형을 측정하여 원형지하매설관의 거동특성을 파악하였다. 타설시 지하매설관은 유동성 뒤채움재의 특성으로 인하여 시간이 지남에 따라 안정화되는 것을 확인할 수 있었으며, 최대하중을 3300kgf로 하여 하중 재하 후 지하매설관의 거동특성은 대체적으로 일반 모래를 사용하여 실험한 값보다 적은 변형 특성을 보이고 있으나 수평토압의 경우 일반적인 흙의 변형과 전혀 상이한 결과값을 보이는 경우도 있어 추가적인 실험 및 고찰의 필요하다. 본 실험에서 사용한 최적배합비 이외의 배합으로 같은 실험을 수행하여 바텀애시 량의 가감 및 재활용 재료인 폐타이어 고무칩등을 첨가한 실험을 계획하고 있으며 추후 실내시험과 모형실험을 토대로 유한요소해석을 추가로 시행하여 실험값과 해석값의 비교를 할 예정이다.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.2
• /
• pp.10-17
• /
• 2000

현대 생활에서 대부분의 사람들은 90%이상을 실내(가정, 일반사무실, 실내작업장, 공공건물, 지하시설물, 상가, 음식점, 자동차, 지하철 등)에서 생활하기 때문에 실내공기질(indoor air quality)은 개인이 오염물질에 노출되는 주요한 요인이다. 이산화질소($NO_2$)는 고온의 연소과정에서 발생되는 부산물로써 차량, 발전소와 산업장 등에서 발생되고 있다. 실내에서 이산화질소의 농도는 가스레인지, 케로센(kerosene) 난방기, 흡연에 주로 영향을 받는다. $NO_2$는 호흡기 증상과 관련된 각종 질환을 유발시키는 것으로 보고되고 있다. 본 연구는 한국의 서울에서 직장인 95명의 시간활동도가 조사되었으며, 호주 브리스베인에서 직장인 57명의 시간활동도와 동시에 각 가정의 실내.외 및 직장의 $NO_2$ 농도를 측정하였다. 또한 개인 $NO_2$ 노출을 예상하여 각 도시의 빈도분포를 예상하였다. 본 연구의 결과를 보면 다음과 같다. 1. 서울의 95명의 직장인들은 실내에서 약 83.8%의 시간을 보냈으며, 브리스베인의 57명의 직장인들은 실내에서 약 88.3%의 시간을 보냈다. 2. 브리스베인에서 측정된 실내의 NO2 평균농도는 10.5ppb(${\pm}5.6$), 실외의 NO2 평균농도는 14.5ppb(${\pm}5.8$), 직장에서의 $NO_2$ 평균농도는 18.2ppb(${\pm}5.0$)였다. 개인의 $NO_2$ 노출은 평균 15.0ppb(${\pm}5.2$)였다. 개인의 $NO_2$ 노출은 실외의 $NO_2$ 농도(r=0.42)보다 실내의 $NO_2$ 농도(r=0.42)보다 실내의 NO2 농도(r=0.49)에 상관성이 더 높았다. 3. 시간 가중치 모델을 이용한 개인 $NO_2$ 노출은 측정된 개인 NO2 노출과 통계학적으로 상관성을 가지고 있었다(r=0.58). 예측된 개인 $NO_2$ 노출은 측정된 $NO_2$ 노출보다 낮게 나타났으며, 이것은 출퇴근 등에 의한 교통의 이동에 따른 노출 때문인 것으로 생각되었다. 4. $NO_2$ 농도 분포를 log-normal 분포, 시간활동도를 Normal 분포로 가정하고 Monte-Carlo 시뮬레이션을 했을 때 서울의 직장인의 개인 노출은 평균 36.7ppb(${\pm}10.9$)였으며, 브리스베인의 직장인의 개인 노출은 평균 13.7ppb(${\pm}4.1$)였다.