• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.467-467
• /
• 2016

암거는 일반적으로 용수나 배수용의 수로가 도로, 철도, 제방 등의 아래에 매설 된 수로를 지칭한다. 이러한 암거는 산업발전으로 사회기반시설의 신설 및 확충, 재정비 등으로 많이 활용되고 있다. 최근 들어 기후로 인한 재해가 급증하면서 이러한 시설물에 대한 안정성 및 관리에 대한 관심이 높아지고 있는 것이 현실이다. 특히 소하천은 집수면적 및 유로연장이 짧고 하상경사가 급하기 때문에 홍수에 취약하다. 즉, 빨라진 유속으로 인해 구조물 주변의 세굴에 의한 유실, 토사유출로 인한 하상퇴적, 부유물로 인한 차단으로 인해 통수에 지장을 받아 피해가 발생하게 된다. 이러한 암거시설물 피해는 2차 피해로 이어질 수 있으며 사회기반시설 파괴로 도시기능이 마비되고 인근 주변지역에 침수로 인한 재산 및 인명피해까지 발생시킬 수 있는 피해 잠재능력을 보유하고 있다. 그러나 피해에 대한 예방대책은 유지관리를 통해 지속적으로 관리하는 것이 대부분의 지침 등에 소개된 내용들이다. 본 연구에서는 암거를 대상으로 암거의 폐색으로 인해 암거주변에서 변화되는 흐름특성을 축소모형을 통해 검토하고자 하였다. 암거 축소모형실험은 1.5m 폭을 갖는 직선수로에서 수행하였으며, 암거모형은 도로암거표준도(2008)를 참조하여 $3m{\times}3m$ 수로암거를 대상으로 1/10 축소모형을 제작하였다. 암거유입부 퇴적으로 인한 암거의 차단률(차단면적/암거단면적)은 차단이 발생하지 않는 0% 조건에서부터 10%, 20%, 30%, 40%, 50% 조건에 대해 실험을 수행하였다. 실험결과 차단에 따른 암거 상류단의 수위는 차단이 없는 암거의 경우에 비해 차단율이 높아질수록 암거유입부 수위는 20.4% ~ 82.7% 상승하는 것으로 나타났다. 암거의 차단률이 40% 이상일 경우 높아진 수위로 인해 암거통로의 윗상면부까지 다다르고 있으며 50%일 경우 암거를 통과하는 흐름이 자유수면흐름이 아닌 오리피스 흐름이 발생하는 것으로 나타났다. 암거유입부 차단으로 인한 암거주변의 최대유속은 암거 직하류부에서 주로 발생하여 암거 유출부에서의 최대유속은 차단율이 증가할수록 선형적으로 증가하는 것으로 나타났으며 암거 유출부에서의 유속은 차단전의 조건(0%) 대비 4.2% ~ 35.5% 까지 상승하는 것으로 나타났다. 이와 같은 결과를 토대로 고려하였을 때 대부분 산지부에서 설치되는 암거의 경우 유속이 불가피하게 증가하게 됨으로 유속에 따른 유속조절방안(차단 및 우회시설) 및 세굴대책을 세워야 할 것으로 판단된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.394-394
• /
• 2015

급격히 변화하고 있는 산업화와 도시화로 지구 온난화 현상으로 기상이변의 발생빈도가 높아졌고 기후가 불안정하여 예전보다 많은 집중호우가 발생하면서, 홍수로 인한 제내지 침수가 발생되기도 한다. 기후변화로 인한 수재해에 대응하기 위하여 하천 호소 수리 예측 모형의 개선이 필요한 실정이다. 하지만, 자연하천 유역의 강우-유출 상관관계와 지표면 유출현상 및 하도 수리 특성을 자연현상의 복잡성, 강우발생의 시간적 공간적인 발생과정의 임의성, 정확한 해석방법 및 확률 분석에 따르는 불확실성 들을 토대로 단순한 이론과 제한적인 경험공식 등에 의해서 해석, 재현 및 평가를 한다는 것은 매우 어려운 문제이다. 최근 IT 기술의 발전과 더불어, 많은 연구자, 엔지니어들이 기존 수리 수문학적 지식과 IT기술을 융합하여 복잡 다단한 수자원 환경 문제를 해결하고자 한다. 이와 같은 최근 연구 동향에 의거하여, 본 연구에서는 HEC-RAS, TELEMAC-2D 1, 2차원 수리 모형을 연계하여 하천 흐름 분석 및 홍수 범람 해석에 적용하였다. 본 연구에서는 HEC-RAS, TELEMAC 모형을 적용하여 2012년 태풍 '산바(SANBA)'로 인해 홍수 피해를 입은 고령군에 위치한 낙동강 본류 회천 유역(상류 회천교 ~ 하류 도진교)의 하도 내 흐름 분석과 하천 인근 제내지 홍수범람을 예측하였다. 범람해석에 필요한 지형자료를 기초로 하여 각 지형의 조건에 맞게 수치자료를 이용하여 작성하였고, 수자원 정보를 이용하여 유랑, 수위 등 시계열자료를 지류 및 상 하류의 경계조건으로 설정하고, 조도계수 등 하천 기본정보들을 입력하였다. HEC-RAS 모형은 회천교부터 도진교까지 전구간에 대한 종단면과 횡단면별 홍수침수범위 및 홍수위 크기 등 거시적인 1차원 수리해석에 적용하였고, TELEMAC 모형은 HEC-RAS 시뮬레이션 결과를 바탕으로 HEC-RAS에서 나타내기 힘든 2차원 흐름특성, 침수현상 등 일부 범람 구간에 대해 수리해석에 적용하였다. HEC-RAS 시스템은 수공구조물들의 영향과 하천의 영향을 종 횡단면으로 다양한 홍수침수 범위를 1차원으로 나타 낼 수 있으며, TELEMAC 시스템 수리 모의를 통해 얻어진 결과는 유속, 유량, 수심, 하상고 높이 등 2차원으로 나타낼 수 있다. TELEMAC 시스템을 활용한 2차원 분석은 실측자료와 비교적 유사하고 시각, 공간적으로 이해하기 쉽게 표현되므로, 모형 적용성이 우수한 것으로 판단된다. 향후 유역 해석을 위한 수치데이터, 수위, 유량자료를 확보하여 HEC-RAS, TELEMAC 1, 2차원 연계 모형을 적용 한다면, 하천 준설, 하천 구조물 설치, 홍수피해 등 전반적인 하천관리 계획에 활용할 수 있을 것이라 판단된다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.846-855
• /
• 2021

Eco-friendly and renewable energy sources are actively being researched in recent times, and of shore wind power generation requires advanced design technologies in terms of increasing the capacities of wind turbines and enlarging wind turbine installation vessels (WTIVs). The WTIV ensures that the hull is situated at a height that is not affected by waves. The most important part of the WTIV is the leg structure, which must respond dynamically according to the wave, current, and wind loads. In particular, the wave load is composed of irregular waves, and it is important to know the exact dynamic response. The dynamic response analysis uses a single degree of freedom (SDOF) method, which is a simplified approach, but it is limited owing to the consideration of random waves. Therefore, in industrial practice, the time-domain analysis of random waves is based on the multi degree of freedom (MDOF) method. Although the MDOF method provides high-precision results, its data convergence is sensitive and difficult to apply owing to design complexity. Therefore, a dynamic amplification factor (DAF) estimation formula is developed in this study to express the dynamic response characteristics of random waves through time-domain analysis based on different variables. It is confirmed that the calculation time can be shortened and accuracy enhanced compared to existing MDOF methods. The developed formula will be used in the initial design of WTIVs and similar structures.

• Journal of the Korean Society of Radiology
• /
• v.15 no.6
• /
• pp.899-909
• /
• 2021

In Musculoskeletal ultrasound examination, a linear transducer (12-5 MHz) with a contact surface length of 6 cm, which is commonly distributed in medical institutions, does not contact with bent fingers and wrist depressions only by using a conventional liquid ultrasound gel, which causes image loss. In order to solve this image loss, the use of commercially available Water gel pad is increasing. However, it is a disposable medical product. Repeated use is prohibited and expensive. In this study, in order to reduce the economic burden caused by the use of the commercialized Water gel Pad, we searched for water-soluble food thickener powder that can be easily purchased around our lives and manufactured Gel pads. Among them, kappa-Carrageenan Gel Pad, iota-Carrageenan Gel Pad, and Agar-Agar Gel Pad satisfied the evaluation criteria without artifacts in image evaluation using the N-365 Multipurpose Phantom. Also, the price to purchase the food thickener powder was about 38 times cheaper than the existing commercialized Water gel pad. As a result, if you use the food thickener powder such as kappa-Carrageenan, iota-Carrageenan and Agar-Agar to make solidified elastic Gel pad without a cover instead of the commercially available expensive disposable Water gel pad, the convenience and usefulness of use are improved. It is judged that the manufactured Gel pads can contribute well to the role of efficient ultrasound propagation medium.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.3
• /
• pp.170-179
• /
• 2019

In this study, the wave responses in a 'Y'shape water channel resonator for amplifying wave energy of a low density has been investigated. A water channel resonator is composed of the long channel and wave guider installed at the entrance. If the period of the incident waves coincides with the natural period of the fluid in a water channel resonator, resonance occurs and the internal fluid amplifies highly to a standing wave form. In order to analyze the wave response in a water channel resonator, we used the matched asymptotic expansion method and boundary element method. The both results were in good agreement with the results of the model test carried out in the two-dimensional wave tank of Jeju National University. Wave guider has an optimum length and installation angle according to the period of the incident wave, and especially effective in enhancing the amplification factor in a period range deviated from the resonance period. It is expected that the wave energy can be effectively extracted by placing the point absorber wave energy converter at the position of anti-node where the maximum wave height is formed by the internal fluid resonance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.269-275
• /
• 2019

As the national industry is developing gradually due to the expansion of the economic scale, the construction of large and super high-rise structures for building social infrastructure has been increasing, and studies have been conducted actively to transmit the large loads at the upper portion to the lower bedrock. In this study, the PHC was extended to an ultra-high strength PHC, which increased the concrete compressive strength of the PHC from the conventional 80 MPa to 110 MPa, and the PHC, which extended the tip of the pile. After construction with the driving method and injected pile method, the tendency of the bearing capacity was tested through a load test. Measurements of the bearing capacity of the extended PHC using the pile driving method revealed the main surface friction force to be smaller than that of the general PHC, and the stet-up effect was also insignificant. On the other hand, the effect of the friction force on the ground surface when the injected pile method was applied is expected to increase the bearing capacity when the gap between the main surface and the ground is wide and the cement paste is filled tightly. In addition, the ultrahigh strength PHC showed higher bearing capacity than the conventional PHC, and the permissible pile stress was less than 60%. Therefore, it is possible to reduce the number of piles and reduce the construction cost and effect of shortening the length of the pile by designing the tip of the pile on the ground with the intensity of soft rock as a method for utilizing the increased strength of the ultra-high strength PHC.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.3
• /
• pp.5-16
• /
• 2019

With the recent concentration of urban populations, the constructions of large structures are increasing, along with the development of foundations for large structures. PHC Piles have been used in many structures ever since Japanese introduced the technology at the end of the 20th century. Recently, many studies on the use of the PHC Pile have been carried out as earth retaining using the merits of PHC piles. In this study, static axial compression tests were conducted on the PHC-W piles constructed as column-type in building underground additional wall using the PHC-W earth retaining wall. The end bearing capacity of pile was calculated using the axial load transfer measurement that was obtained from the static axial compression test result. Since end bearing capacity of the PHC-W pile embedded in weathered rock showed a different behaviour from the conventional PHC pile, the calculation method of end bearing capacity for column-type PHC-W piles would be proposed. The unit ultimate end bearing equation proposed for single and group PHC-W pile embedded in weathered rock is $q_b=13.3N_b$ and $q_b=6.8N_b$.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.3
• /
• pp.397-418
• /
• 2019

It is very important to understand and analyze the interactive behaviour between ground and adjacent structures due to tunneling. With many technological advancement in modern society, numerous methods for analyzing the interactive behaviour are used in a wide range of civil engineering fields. Close range photogrammetry is mainly being used in the field of geotechnical engineering and research on measuring methods associated with GeoPIV has been currently increased. Originally, the close range photogrammetry using target points and aluminum rods for VMS (Vision Measurement System) program has been used. However, applying this has a problem that external errors can be occurred because the target points are artificially installed by hand, and if the grid between points is being wider or narrower, deficient data can be obtained. Therefore, in this study, MATLAB-based No-target program that can analyze displacement without using target was developed. Additionally, this study focused on comparison and verification with existing program through numerical analysis and laboratory model test. Three cases of Greenfield condition, Strip foundation, and Pile foundation were analyzed. From results of VMS program and No-target program, the error rate and reliability of the total displacement and the vertical displacement were analyzed. It was also compared and verified through the finite element numerical program, PLAXIS.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.330-337
• /
• 2021

3D printing is not only at the fundamental study and small-scale level, but has recently been producing buildings that can be inhabited by people. Buildings require a lot of cost and labor to work on the form work, but if 3D printing is applied to the building, the construction industry is received attention from technologies using 3D printing as it can reduce the construction period and cost. 3D printing technology for buildings can be divided into structural and non-structural materials, of which 3D printing is applied to non-structural materials. Because 3D printing needs to be additive manufacturing, control such as curing speed and workability is needed. Since cement mortar has a large shrinkage due to evaporation of water, cement polymer dispersion is used to improve the hardening speed, workability, and adhesion strength. The addition of polymer dispersion to cement mortar improves the tensile strength and brittleness between the cement hydrate and the polymer film. Cement mortar using polymer materials can be additive manufacturing but it has limited height that can be additive manufacturing due to its high density. When light-weight materials are mixed with polymer cement mortar, the density of polymer cement mortar is lowered and the height of additive manufacturing, so it is essential to use light-weight materials. However, the use of EVA redispersible polymer powder and light-weight materials, additional damage such as cracks in cement mortar can occur at high temperatures such as fires. This study produced a test specimen incorporating light-weight materials and EVA redispersible polymer powder to produce exterior building materials using 3D printing, and examined flame resistance performance through water absorption rate, length change rate, and cone calorimeter test and non-flammable test. From the test result, the test specimen using silica sand and light-weight aggregate showed good flame resistance performance, and if the EVA redispersible polymer powder is applied below 5%, it shows good flame resistance performance.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.12
• /
• pp.57-67
• /
• 2009

Along with the advanced construction technologies, the maximum size of coarse aggregate used for dam construction ranges from several cm to 1m. Testing the original gradation samples is not only expensive but also causes many technical difficulties. Generally, indoor tests are performed on the samples with the parallel grading method after which the results are applied to the design and interpretation of the actual geotechnical structure. In order to anticipate the exact behavior characteristics for the geotechnical structure, it is necessary to understand the changes in the shear behavior. In this study, the Large Triaxial Test was performed on the parallel grading method samples that were restructured with river bed sand-gravel, with a different maximum size, which is the material that was used to construct Dam B in Korea. And the Stress - Strain characteristics of the parallel grading method samples and the characteristics of the shear strength were compared and analyzed. In the test results, the coarse-grained showed strain softening and expansion behavior of the volume, which became more obvious as the maximum size increased. The internal angle of friction and the shear strength appeared to increase as the maximum size of the parallel grading method sample increased.