• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1906-1908
• /
• 2004

본 논문은 옥외용 고분자 절연물로 널리 사용되고 있는 실리콘 고무의 장기 자외선 가속열화에 따른 특성변화를 조사하였다. 이를 위해 전기적인 평가 방법 이외에 각종 화학적 분석기기를 사용하여 보다 정확히 재료의 열화를 판정하고자 하였다. 연구결과, 실리콘 고무는 내후성이 우수하지만, 가속열화가 진행되면서 표면의 전기적 저항률이 높아지고, 전하축적이 용이해지는 표면구조로 변하는 것을 확인하였다. 또한, 재료 내에서 발수성 회복역할을 하는 저분자량 성분이 감소하였고, 열적특성이 변화되는 것을 확인하였다. 이를 통하여, 최근 확산되고 있는 옥외용 고분자 절연물의 성능평가 및 수명예측에 도움이 되고자 하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.70-76
• /
• 2012

For Analysis and evaluation of ALC carbonation, ALC with various specific gravity was fabricated and silicate and siloxane were used for spraying on ALC surface. Silicon oil of water repellent was added to ALC slurry. ALC carbonation related with specific gravity and carbonation degree was decreased with specific gravity. It was guessed that permeation of $CO_2$ gas reduced depend on compact structure of ALC. ALC which sprayed silicate and siloxane represented more excellent carbonation resistance than Ref. ALC. ALC added silicon oil represented most excellent carbonation resistance.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.107-112
• /
• 2016

In this paper, the hydrophobic rough surfaces were prepared by employing a conventional nano-imprint lithography technique, and the effects of surface parameter, ratio of the top surface to the flat unit cell, on the impingement behaviors of liquid droplet were investigated to improve robustness of hydrophobic functionality. The critical height defined for the transition from rebound to fragmentation is measured by droplet impingement test in order to study dynamic behavior of an impinged droplet. It showed the critical height decreased with high surface parameter while it increased with low surface parameter. However, the critical height decreased again as surface parameter decreased further. Observed results suggest that the optimized surface pattern should be designed for the increased critical height.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.3
• /
• pp.78-91
• /
• 2011

The Usuki Stone Buddha Statues in Japan are carved on mainly dark gray welded lapilli tuff accompanied by lenticular fiamme. This rock is composed of matrix which contains feldspar and opaque minerals with some phenocrysts of quartz and feldspar. The matrix is slight to highly welded. The statues have been weathered and weakened by salt and freezing of water. To enhance the mechanical properties of the rock, consolidants and water repellents were applied. The absorption ratio of the rock was highly decreased after the treatment of the water repellents, the consolidant OH 100, as well. Ultrasonic velocity revealed similarly higher values in the treated rock by KSE 300 and OH 100, compared to non-treated rock. KSE 300, especially, highly increased the Equotip surface hardness. All studied consolidants and water repellents were found to change the original color of the stone. SNL, specifically, resulted the significant change in color. In addition, KSE 300 were observed to improve resistance to weathering such as microcrack and fracture through freezing-thawing test after treatment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.597-600
• /
• 2001

In this paper, we evaluated the effect of accumulated charges on hydrophobicity of room temperature vulcanized(RTV) silicone rubber, which could improve the contamination performance of porcelain insulators, with uv radiation time. Outdoor insulating material could be charged by the corona discharge on field intensified area of insulator and discharge between the water drops. In addition, we performed the accelerated uv radiation on samples and investigated the change of charging decay with time. In this results, it is found that silica-like structure on the surface of RTV silicone rubber was formed by uv treatments and this layer have the characteristic of retaining the charges on surface for a long time. These charges have effects on its hydrophobicity and so adversely effects on contamination performance. Based on our results, we discussed the other degradation mechanism with well known ones.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.1-10
• /
• 1999

In this paper, we have investigated the effects of the environmental factors on Low Molecular Weight (LMW) silicone fluid contents existing in high temperature vulcanized (HTV) silicone rubber sample, using dipping method and contact angle, current measurement. Artificial treatments such as immersion in water, elevated temperature, UV irradiation and dry band arcing under salt-fog condition are selected as the environmental factors. This results will be helpful to investigate the degradation with time and to expect a life time, because the LMW silicone content, which is important to recovery the hydrophobicity of silicone rubber surface, show different results by each environmental factors.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.124-132
• /
• 2019

Water-repellent coating solutions were synthesized by hydrolysis and polycondensation reactions with water using tetraethoxysilane (TEOS) and chlorotrimethylsilane (CTMS) as precursors. The solutions were coated on a PMMA sheet and thermally cured to prepare non-fluorinated water-repellent coating films. Coating films were characterized by water contact angles, UV-Vis transmittance and surface morphology. The contact angle of coating films prepared by varying the molar ratio of CTMS/TEOS to 0.6~1.0 exhibited a maximum value of $107^{\circ}$ when the CTMS/TEOS molar ratio was 0.8. The coating films showed a high transmittance over the visible range up to 90% when the CTMS/TEOS molar ratios were 0.6~0.8. However, when the molar ratios of CTMS/TEOS were 0.9~1.0, the transmittance of coating films was lower than 70% due to an uneven shape of the rough surface.

• Journal of Conservation Science
• /
• v.26 no.3
• /
• pp.325-334
• /
• 2010

In order to clarify the effect of consolidant, the artificial porous material with low intensity was manufactured using granite powder and Portland cement. We have prepared four kinds of alkoxysilane system consolidants, a acrylic resin and a epoxy resin and investigated about characteristics before and after consolidation. As a result of the research, Silres BS OH 100 was effective for density and surface hardness. SS-101 with hydrophobicity and Site SX-RO with hydrophilicity had the good durability over salts weathering. On the other hand, Syton HT-50 and Paraloid B72 were easily destructed by salt weathering because they were concentrated on surface area by the low penetration depth. Araldite 2020 was the most effective consolidant for improvement of physical properties.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2004.05b
• /
• pp.156-159
• /
• 2004

TFEMA(2,2,2-trifluoroethylmethacrylate)는 광섬유 코팅제, 발수 발유제, 기능성 페인트, 방오가공제, 고분자의 표면개질제 등의 많은 응용제품에 활용되는 단량체로 그 시장규모가 국내에서 600억원, 전 세계에서 8,000억에 해당하는 고부가가치의 화학원료이다. TFEMA는 현재 산촉매하의 8.$0^{\circ}C$의 고온에서 TFEA(2,2,2-trifluoroethaol)와 MA(methacrylic acid)와의 에스텔화 반응으로 제조된다.(중략)

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.75-75
• /
• 2010

배변 후 toilet flushing 시 다량의 세균을 포함한 물방울들이 화장실 곳곳으로 퍼지는 현상이 있다. 이러한 현상을 방지하기 위해 변기 뚜껑에 자기 세정 효과를 갖는 초발수 표면을 위해 플라즈마를 이용한 표면 처리가 시도되고 있으며, 이 연구의 일환으로 flushing시의 변기내의 유동 분석을 초고속 카메라를 이용하여 수행하였다. Toilet flushing 시 물 튀김 현상은 육안으로는 잘 관찰하기 어렵지만 최고 1000 frame/sec의 속도를 갖는 CCD camera를 이용하여 정량적으로 물 튀김에 의한 오염 가능성을 촬영 분석하였다, 두 번째로 소변 시의 변기 표면에서의 튀김현상을 분석하기 위하여 소변의 발사각도 및 속도를 가장 실제와 유사한 조건으로 설정하고 이를 상용 전산 유체 역학 소프트웨어인 CFD- ACE+의 자유 표면 계산 기능과 두 가지 유체(액체 및 기체)의 혼합 계산 모델을 사용한 계산 결과와 비교 하였다. 그 결과 변기 표면의 표면장력을 아주 작게 설정한 경우(작은 접촉각, 친수성)에는 중력의 영향을 고려하였음에도 불구하고 소변이 변기에 충돌 후 상부로 상당부분 튀어 올라가는 결과를 얻었다. 여러 가지 각도와 발사 속도, 실제의 인체와 유사한 발사 부위의 형상 변화로 인한 유체 표면의 난류 발생과 이에 따른 변기 표면 충돌 현상 변화 등을 수치적으로 고찰하였다. 한 예로 5.6 mm 직경의 노즐에서 소변이 나오는 경우를 발사 속도 3 m/s, 각도 $10^{\circ}$로 주고 중력을 고려하여 10초 동안을 계산하면, 방뇨 시 toilet bowl 내부에서의 물의 유동과 toilet 표면을 맞고 튀기는 현상을 그림 1과 같이 볼 수 있었다.