• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.219-223
• /
• 2004

Since rotor position information is necessary to drive the SRM, absolute-encoder, resolver and incremental encoder is used to detect a rotor position. But, it is not desirable to use a high price encoder and microprocessor under the condition of the simple driving system when precision control is not demanded. In this paper, only using the reflective type two photo-sensors replaces the conventional opto-interrupter and slotted-disk, which not only remove a slotted-disk section but drive three-phase 6/4 pole SRM bidirectionally, Therefore, control circuit can compose common analog device with low price.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.23-27
• /
• 2004

Information of rotor position is necessary to drive Linear Switched Reluctance Motor(LSRM). Therefore, linear optical encoder is used to detect a mover position. Normally, since the price of encoder, which is used for linear motor is relatively higher than the one used for rotory motor and the cost of additional equipment increases with the length of motor. As a results, LSRM has a great part for the total cost. In this paper, as using reflective type photo-sensors, it replaced the expensive linear encoder.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.142-149
• /
• 1999

In this paper, Aperture-coupled microstrip array antenna was designed and manufactured for satellite communication at Ka-Band. We analyzed a microstrip radiation element and designed power divider using $\lambda$g/4 transformer and T-junction power divider. A manufactured Aperture-coupled $2\times2$ microstrip array antenna has a resonant frequency of 20 GHz. The experimental results are as followings : resonant frequency of 19.62 GHz, VSWR 1.0692, return loss -29.61 dB, Bandwidth 1.76 GHz and -3 dB beamwidth $42^{\circ}$.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1999.06b
• /
• pp.9-13
• /
• 1999

이 논문은 디지털 TV 송신기의 구성 시스템 중 하나인 HPA 서브시스템(이하 HPA 시스템이라고 함)을 구현하는 구현 기술에 대하여 기술한다. HPA 시스템은 레벨 제어부, HPA 모듈, 고출력 결합기, 여파기, HPA 감시, 경보 및 제어 시스템으로 구성되어 있다. 이를 구현하기 위해서 전력레벨을 설계하고, 각 레벨에 맞는 4Wpeak, 30Wpeak, 125Wpeak 단위 증폭기를 설계, 제작 시험하였으며, 이들 단위 증폭기를 전력 분배기/결합기를 이용하여 결합하여 600Wpeak급 HPA 모듈을 제작하였다. 자체 제작한 HPA 모듈과 상용 부품을 이용하여 HPA 서브시스템을 구성하였으며, 현장시험을 통하여 그 성능을 입증하였다. 개발한 HPA 시스템은 동작주파수 470MHz-510MHz, 최대출력 1.6kWpeak, 이득 60dB 이상, 채널내 이득 평탄도 0.6dB 이하, 입력 반사손실 -l8dB이하이며, IMD는 3dB back-off시 -35dB이하이다

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.3
• /
• pp.159-166
• /
• 2018

Herein, a non-Foster matching circuit is designed to improve the impedance matching characteristics of small antennas in the VHF and UHF bands. The proposed non-Foster circuit is designed to operate with negative capacitance in a wide frequency band from 50 MHz to 1,000 MHz for use in various communication bands. To ensure the stability of the non-Foster circuit with conditional stability, the open-circuit stability condition of Linvill was satisfied, and the circuit was fabricated using the FR-4 substrate. The fabricated non-Foster circuit was combined with a small antenna to verify its performance by measuring the return loss and received power in the FM, DMB, and GSM bands. The measured return loss was improved from -6 dB to -30 dB, and the measured received power was improved from 0.5 dBm to 5.2 dBm.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.4
• /
• pp.25-33
• /
• 1999

Leaky wave radiation and surface wave launching problems in a dielectrically covered and periodically slitted parallel-plate waveguide(PPW) are considered for the TEM wave incidence case. Both the infinite and finite periodic geometries are analyzed by use of the method of moments. Some numerical results for the reflected and transmitted powers in the PPW, radiation efficiency into the free space, surface wave launching efficiency into the slab, antenna gain, and radiation patterns against dielectric thickness are presented to show the effect of the dielectric cover on the performances of the slitted leaky wave antenna. In addition, the method for improving surface wave launching efficiency using the proposed periodic geometry is described and maximum launching efficiency of 97.5% is obtained theoretically. So this structure is thought to be promising as an efficient feeder of dielectric grating antenna as well as image guide.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.12
• /
• pp.1876-1883
• /
• 2016

The new channel model for high data rate common data link(CDL) is proposed. The Two-ray channel, which is composed of the reflected signals on the front ground of the receiver, is considered in this paper. This channel arises due to the curvature of the earth when the altitude of the transmitter is tens of kilometers and distance between the transmitter and the receiver is hundreds of kilometers. The Two-ray channel is modeled by estimating the maximum delay profile and the power delay profile, depending on the transmitting and receiving beamforming angle and the radiation pattern of antenna. The power delay profile has a larger effect on the bit error rate(BER) over signal to noise ratio(SNR) than the maximum delay profile, because the distance range is too long in the proposed channel model.

• Journal of Digital Convergence
• /
• v.14 no.1
• /
• pp.181-187
• /
• 2016

Typical Retro-reflectors installed on road have problems such as limiting a driver's visibility at night when it is foggy or rainy. On the other hand, LED illuminated studs, called cat's eye system, extends a driver's visibility under these conditions. In this paper, we present a design of the LED cat's eye system using solar energy that can sustain vehicles with about 30-ton weight and is compliant with the IP68 code for water proof as IEC standard 60529. In addition, we propose a scheme of designing a LED driving circuit consuming low power to take into accounts cold weather or rainy season with limited sunlight. This LED cat's eye studs is currently installed and used on expressway and bike route nationally as well as overseas.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1055-1061
• /
• 1999

Indium Tin Oxide (ITO) films were fabricated by vacuum deposition technique and their microwave shielding properties were investigated for the application to the transparent shield material. The vacuum coating was conducted in a RF co-sputtering machine. The film composition and structure associated with the sputtering conditions (argon and oxygen pressure. substrate temperature. RF input power) were investigated for the attainment of high electrical conductivity and good transparency. The electrical conductivity of IT0 films fabricated under the optimum deposition conditions (substrate temperature : $300^{\circ}C$. Ar flow rate : 20 sccm, Oxygen flow rate : 10 sccm, In/Sn input power : 50/30 W) showed 5.6$\times10^4$mho/m. The optical transparency is also considerably good. The microwave shielding properties including the dominant shielding mechanism are investigated from the electrical conductivity, thickness and skin depth of the ITO films. The total shielding effectiveness is then estimated to be 26 dB, which provides a suggestion that the IT0 films can be effectively used as the transparent shield material.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.2
• /
• pp.87-92
• /
• 2016

In this paper, the solutions of TE(transverse electric) scattering problems by a conductive strip grating over two dielectric layers are analyzed by applying the PMM(point matching method) known as a numerical method of electromagnetic field. The boundary conditions are applied to obtain the unknown field coefficients, the scattered electromagnetic fields are expanded in a series of Floquet mode functions, and the conductive boundary condition apply to analysis of conducting strip. The most normalized reflected and transmitted powers having a sharp variations are scattered in direction of the other angles except incident angle. The numerical results for the normalized reflected and transmitted powers are analyzed by according as the width and spacing of conductive strip, incident angles, and the relative permittivity and thickness of the two dielectric layers. To confirm the validity of this paper, the numerical results of presented structure are shown in good agreement compared to those of the existing papers.