• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.81-86
• /
• 2007

Biodiesel fuel that consists of saturated and unsaturated long-chain fatty acid alkyl esters is an alternative diesel fuel produced from vegetable oils or animal fats. However, air causes autoxidation of biodiesel fuel during storage, which can reduce fuel quality by adversely affecting its properties, such as the kinematic viscosity and acid value. One approach for improving the resistance of fatty derivatives to autoxidation is to mix them with antioxidants. This study investigated the effectiveness of five such antioxidants in mixtures with biodiesel fuels produced by three biodiesel manufacturers : tert-butylhydroquinone (TBHQ), butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), propyl gallate (PrG) and $\alpha$-tocopherol. Oxidation stability was determined using Rancimat equipment. The results show that TBHQ, BHA, and BHT were the most effective and $\alpha$-tocopherol was the least effective at increasing the oxidation stability of biodiesel. This study recommends that TBHQ and PrG be used for safeguarding biodiesel fuel from the effects of autoxidation during storage.

• Journal of Power System Engineering
• /
• v.14 no.1
• /
• pp.11-15
• /
• 2010

Our environment is faced with serious problems related to the air pollution from automobiles in these days. In particular, the exhaust emissions from the diesel engines are recognized as main cause which has a great influence on environment. In this study, the potential of biodiesel fuel and oxygenated fuel(ethylene glycol mono-n-butyl ether; EGBE) was investigated as an effective method of decreasing the smoke emission. The smoke emission of blending fuel(EGBE 0~20 vol-%) was reduced in comparison with diesel fuel and it was reduced approximately 64% at 2000 rpm, full load in the 20% of blending rate. On the contrary NOx emissions from biodiesel fuel and EGBE blended fuel were increased compared with diesel fuel. Torque and brake specific energy consumption(BSEC) didn't have large differences.

• Journal of Power System Engineering
• /
• v.12 no.1
• /
• pp.5-12
• /
• 2008

We measured emission characteristics of CRDI diesel engine equipped with a commercial CPF. Experimental parameters adopted a neat diesel fuel, a blend of diesel fuel with 20% biodiesel, a blend of diesel fuel with 15% biodiesel and 5% ethanol. The experiments were carried out to measure the emission and engine performance according to ESC 13-mode cycles. The maximum torque with biodiesel blend fuel is slightly lower than that of neat diesel fuel in the entire the 13-mode cycles, and 5% ethanol and 15% biodiesel blend fuel is slightly higher than that of neat diesel fuel. THC and CO emissions of the biofuel blended diesel fuel were slightly increased and decreased, and mean conversion efficiencies of THC and CO on the commercial CPF were achieved about 70$\sim$87% in the ESC 13-mode. From the measurement by the Scanning Mobility Particle Sizer(SMPS), the total number and mass of nano-sized particles by a commercial CPF were decreased about 97.8% and 96.8 % in the range of the nano-size from 10.6 to 385nm, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.250.2-250.2
• /
• 2010

빛과 공기 중의 이산화탄소를 고정화하여 생성되는 바이오매스(biomass)로부터 다양한 에너지 및 물질을 생산하는 연구는 석유고갈과 환경문제 해결의 한 방안으로서 활발히 진행되어 왔으며, 앞으로도 그 지속 가능성과 환경 친화성에 의해 바이오에너지 이용 및 보급은 꾸준한 증가세를 보일 것으로 전망된다. 바이오디젤, 바이오에탄올의 경우는 미국, 브라질, EU, 한국 등에서 상용화되어 사용되고 있으며 그 생산량이 계속적으로 증가하고 있다. 하지만, 바이오연료의 보급 증가는 식량 자원과의 충돌과 열대우림 파괴 등의 부작용을 일으키고 있다. 이러한 문제 해결의 일환으로 단위면적당 생산성이 대두, 유채보다 월등한 것으로 보고되는 미세조류에 대한 관심이 증가하고 있으며 우수 미세조류종 개발, 미세조류 고속배양 및 수확, 미세조류로부터 에너지 및 유용물질, 소재 생산에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 미세조류로부터 바이오디젤 원료유를 생산하기 위해 Soxhlet을 이용한 추출 방법을 이용하였다. 추출되는 오일은 사용 용매의 극성에 따라 물성과 추출 효율에 차이가 큰 것으로 나타났다. 강한 극성의 용매일 경우, 엽록소와 단백질이 같이 추출되는 문제가 있으며 약한 극성 용매는 세포벽의 방해로 용매가 세포내부로 흡수되지 못하는 문제가 있다. 추출 효율이 높은 극성용매의 경우 불순물을 제거해야 고순도의 바이오디젤의 생산이 가능하고 비극성 용매는 추출 오일의 물성은 좋으나 수율이 매우 낮게 측정되었다. 이러한 동시추출을 방지함과 동시에 추출 효율을 높이기 위해 본 연구에서는 세포벽 파괴 후 용매추출하는 방법으로서 미세조류를 Microwave에 노출시켜 오일 추출율을 증가시키는 전처리 연구를 수행하였다. 전처리시, Microwave에 의한 열 발생은 미세조류를 탄화시키기 때문에 열매체로서 물을 혼합하여 탄화를 방지하고 세포벽 내외부의 가열효과로 세포벽을 파괴하고자 하였다. Microwave에 의한 에너지 손실을 줄이며 세포벽 파괴에 효과적인 수분혼합비를 조사하였으며 Microwave에 노출 후 잔류수분을 건조하고 효율적으로 용매를 접촉시키기 위해 분쇄를 수행하였다. 모든 전처리 반응을 거친 미세조류에서 약 2배 증가된 추출수율을 얻을 수 있었으며, SEM을 통해 전처리 미세조류와 미전처리 미세조류를 분석해본 결과 전처리 미세조류의 다공성이 증가함을 확인하였다. 또한, 90%의 메탄올에 미세조류를 녹여 엽록소 함유량을 측정한 결과, 전처리 미세조류의 엽록소가 미전처리 미세조류보다 약 7배가량 감소함을 확인할 수 있었다.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.55-63
• /
• 2014

Pyrolysis oil (PO), also known as Bio crude oil (BCO), has the potential to displace significant amounts of fuels that are currently derived from petroleum sources. PO has been regarded as an alternative fuel for petroleum fuels to be used in diesel engine. However, the use of PO in a diesel engine requires modifications due to low energy density, high water contents, low acidity, and high viscosity of the PO. One of the easiest way to adopt PO to diesel engine without modifications is emulsification of PO with the fuels that has higher cetane number. However, PO that has high amount of polar chemicals is immiscible with non polar hydrocarbons of diesel. Thus, to stabilize a homogeneous phase of diesel-PO blends, a proper surfactant should be used. In this study, a DI diesel engine operated with diesel and diesel-PO emulsions was experimentally investigated. Performance and gaseous & particle emission characteristics of a diesel engine fuelled by diesel-PO emulsions were examined. Results showed that stable engine operation was possible with the emulsions and engine output power was comparable to diesel operation.

• Clean Technology
• /
• v.13 no.2
• /
• pp.104-108
• /
• 2007

Biodiesel is a fatty acid alkyl ester produced by chemical reaction of a vegetable oil or animal fat and an alcohol. It is getting attention as a clean alternative energy that can replace gas oils. In this study, strong acidic ion exchange resin was introduced in the pretreatment process of the used cooking oil and rapeseed oil to enhance the conversion of the oil to the biodiesel by removing FFA(free fatty acid). More than 90% FFA was removed. Dry resins showed higher FFA removal efficiency than wet resins. Using transesterification the conversion of triglyceride into fatty acid methyl ester was raised up to 98%. These results can be applicable to the pretreatment of biodiesel feedstocks having high acidic value.

• KSBB Journal
• /
• v.11 no.2
• /
• pp.159-164
• /
• 1996

Transesterification of used frying oil was investigated to produce the bio-diesel oil. Experimental conditions included molar ratio of used frying oil to alcohol (1:3, 1:5 and 1:7), concentration of catalyst (0.5, 1.0 and 1.5 wt.%), ippe of catalyst(sodium melhoxide, NaOH and KOH), reaction temperature (30, 45 and $60^{\circ}C$), and types of alcohol(methanol, ethanol and butanol). The conversion of used frying oil increased with the alcohol mixing ratio and with the reaction temperature. The effect of the type of catalysts on conversion was not significant. The highest conversion was obtained when methanol was used as alcohol. Viscosity was a little higher with the ester product over grade #2 diesel oil. But the physical properties improved significantly with transesterification, resulting in similar fuel properties with those obtained for grade #2 diesel fuel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.56-62
• /
• 2003

Spray characteristics of conventional diesel fuel and bio-diesel fuel(methyl-ester of soybean oil) were compared, in terms of spray tip penetration and spray angle, by using a commercial high pressure common rail injection system for light-duty DI Diesel engines. The experiments were carried out under the non-evaporating condition at ambient density(8.8, $15.6 kg/\textrm{m}^3$) and injection pressure(75, 135 MPa). The experimental method was based on a laser sheet scattering technique. Spray tip penetrations of bio-diesel fuel were longer, on the whole, than those of conventional diesel fuel, except for lower injection pressure(75 MPa) under lower ambient density$(8.8 kg/\textrm{m}^3)$. But spray near angle and spray far angle of bio-diesel fuel were smaller than those of conventional diesel fuel, implying spray angle is related to the growth rate of spray tip penetration. The experimental results of spray tip penetration agreed well with the calculated values by the Wakuri et al.'s correlation based on the momentum theory.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.5
• /
• pp.603-608
• /
• 2012

Recently we have a growing interest in environmental pollution and alternative energy. Diesel engine is generally used to produce the power on shore and sea. However, the combustion characteristics and exhaust emissions of the engine are changed on account of the wear of fuel system and the altered ambient condition of the combustion chamber by the increment of the engine operation hour. Therefore the combustion characteristics and exhaust emissions on the fuel injection timing were experimentally investigated to find out the optimum fuel injection timing in case of the about 20 years used diesel engine using biodiesel blend oil. The original fuel injection timing of the engine is BTDC $22^{\circ}$ CA. However, it is found that the optimum fuel injection as a result of analyzing the specific oil consumption and exhaust emissions of 20 years used the engine is BTDC $26^{\circ}$ CA.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.81-89
• /
• 2009

In this experimental study, the effects of clean alternative fuels compatible with diesel combustion on nano-sized particle emission characteristics were investigated in a 0.5L auto-ignited single-cylinder engine with a compression ratio of 15. Because the number concentration of nano-sized particles emitted by automotive engine, that are suspected of being hazardous to human health and environment, might increase with engine fuel considerably and recently attracted attention. So a ultra-low sulfur diesel(ULSD), BD100(100% bio-diesel) and Di-Methyl Ether(DME) fuels used for this study. And, as a particle measuring instrument, a fast-response particle spectrometer (DMS 500) with heated sample line was used for continuous measurement of the particle size and number distribution in the size range of 5 to 1000nm (aerodynamic diameter). As this research results, we found that this measurements involving the large proportion of particles under size order of 300nm and number concentration of $4{\times}10^9$ allowed a single or bi-modal distribution to be found at different engine load conditions. Also the influence of oxygen content in fuel and the catalyst could be a dominant factor in controlling the nano-sized particle emissions in auto-ignited engine.