• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.456-461
• /
• 2003

A fuel cell is an electrochemical device in which the energy of a chemical reaction is converted directly into electricity. By combining hydrogen fuel with oxygen from air, electricity is formed, without combustion of any form. Water and heat are the only by-products when hydrogen is used as the fuel source. Fuel cell stack consists of multi-layered unit cells. A unit cell consists of MEA and bipolar plates. The end plate of fuel cell stack should give a uniform distributed pressure to multi unit cell layers so as to reduce the contact resistance and to prevent the leakage of reactant gases and the damage of multi layer components. The current end plate is redundantly large and heavy. It makes the power per unit volume reduced. Topology optimization of end plate is conducted for mass reduction and enhancement of bending rigidity. The evaluation of the current design and the recommendation for the future design is remarked.

• Journal of Energy Engineering
• /
• v.24 no.4
• /
• pp.48-54
• /
• 2015

This study investigates the result of thermal stress analysis on burning plate by classes at outdoor gas boiler. In the analysis results at the steady state, the maximum stress and deformations are 666,8MPa at A type and 0.20476mm at B type respectively. The deformation becomes larger as the field goes on from the center to the outside at burning plate. As there are 8 types in the order of maximum stress and deformation, F and C type have safest among 8 types respectively. Therefore, F type becomes most excellent on strength and safety among 8 types. By using the analysis result of burning plate model at gas boiler, it is possible to design the model applied practically at the safe component parameters of boiler system.

• Animal Systematics, Evolution and Diversity
• /
• v.18 no.2
• /
• pp.233-244
• /
• 2002

As one of the serial studies on the taxonomy of Conthocamptus mirabilis species group in South Korea, C. semicirculus Kikuchi, widely distributed in the southern part of the Far East, and C. coreensis n. sp. from the middle west of South Korea are recorded. Intraspecific variability of some important characters like outer caudal setae and the spinous process of male leg 3 exopod was examined in Korean population of C. semicirculus. Canthocamptus coreensis n. sp. possesses the plesiomorphic characters of the round and narrow hyaline membrane of anal operculum and lacking the sexual reverse transformation in female caudal rami, while it also evolves the apomorphic ones of the modified outer apical setae of male leg 4 exopod and the spinous process of male leg 3 exopod. A key to the five species of the species group known from Korea is prepared.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.1
• /
• pp.17-21
• /
• 1988

To the purpose of keeping net mouth of seine with bag open in the seining operation a novel method was devised and tested with model gear that double textile strips were fixed at both side edges of bag net mouth as sheering devices. The angles of attack of inner and outer strips were the 40 in degrees by adjusting rigging. In seining operation current that flowed between the double strips and generated side force on the strips sheered and opened the net mouth automatically. This paper described dynamic characteristics of the sheering strips and its automatic opening function of net mouth.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.6 s.22
• /
• pp.212-217
• /
• 2004

Carbon fiber reinforced plastic(CFRP) plate Is one of the alterative materials for soengthening of reinforced and prestressed connote members due to excellent strength and light weight In this paper, the behavior of beams strengthened with CFRP plate and CFS(Carbon fiber sheet) is observed and analyzed from the test results. Especially specimens with thick plate is tested when large moment and large shear lone appear in same position. The main failure mode is a peeling-off of the CFRP plate near the loading points due to flexural-shear crack, Because of this failure mode, failure load is not linearly proportional to the thickness of CFRP plates. When beam is wrapped with CFS around oかy loading point it does not influence on the failure loads. Depending on the loading pattern, it is necessary to consider different design criteria for reinforced concrete members with external reinforcement. When line moment and large shear force appear in same location, maximum thickness may limit to 0.6mm and ratio between moment of strengthened beam and moment of unstrengthened beam is proposed 1.5-2.0. In order to use the plate of thicker than 6mm, CFS may be extended to the location which moment of strengthened beam is 1.5 times than moment of unstrengthened beam.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.425-428
• /
• 2011

회전식 스마트 조명 시스템은 기존 식물공장에 무수히 많이 설치되는 LED와 형광등을 대신하여 비교적 적은 양으로 설치된 LED와 형광등을 회전시키는 시스템으로써 작물 재식판의 작물들에게 필요한 광을 회전하며 공급하는 방법이다. 이로 인하여 식물공장에 조명 시스템을 설치할 때 방생되는 고가의 초기 설치비용을 해결하고자 하는 시스템이다. 본 논문에서는 식물이 생장하는데 필요한 광량과 광속, 광양자속 밀도를 계산하고 블레이드에 설치되는 LED의 개수를 설정하였으며, 조명 시뮬레이션 프로그램 Relux를 이용하여 조명 장치가 회전함에 따라 조명장치의 중심과 바깥쪽에 생기는 광량의 차이를 확인 하였다.

• Archives of Craniofacial Surgery
• /
• v.12 no.1
• /
• pp.33-36
• /
• 2011

Background: In a frontal sinus reconstruction, the literature primarily recommends a surgical approach for definite treatment with the exception of for anterior wall fractures with no dislocation. Many studies have assessed a range of methods for the reduction of frontal sinus fractures. This paper presents a case, in whom the anterior wall of the frontal sinus was reconstructed using an outer table calvarial bone graft in an en bloc manner. Patient and methods: A 36-year-old male visited the emergency room with a heavy injury to the forehead. He was diagnosed with fractures of the anterior and posterior wall of the frontal sinus. The neurosurgeon removed the fractured area and repaired the meninges. Afterwards, cranialization was performed and the opening of the nasofrontal duct was obstructed. After fixing the removed bone to its original location, all fragments of fractured anterior wall were purged out and the anterior wall reconstructed using an en bloc calvarial bone graft. Results: In the post-operative 8 months period, there were no complications, the round contour of the forehead was expressed well and the patient was satisfied with the result. Conclusion: There are many methods for reconstructing the anterior wall of the frontal sinus. On the other hand, in cases of large fracture sites with many fractured bone fragments, en bloc harvesting of the outer table calvarial bone could be a better choice than making use of only plates and screws because this method shows a good results in terms of aesthetics with a low complication rate.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.5-15
• /
• 2004

It is worthwhile to verify the vertical stress distribution in soil mass for rigorous design of foundation. A series of laboratory model tests were performed to investigate the Boussinesq's theory on vertical stress increment in sandy soil mass caused by surface loading. The test results were also compared with Boussinesq's theoretical values. The Boussinesq's theoretical values were always smaller than test results under the footing regardless of depth. Outside of the footing the values were larger than the measured stress at the depth of just footing width. The theory and the test showed similar results when the depth reached two and three times the footing width. The vertical stress decreased as the applied load increased. These trends were confirmed to be valid for the considered range of the relative density of sand and/or the width of footing. More accurate values can be acquired by correcting the theoretical values using these results when Boussinesq's theory is used.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.1
• /
• pp.35-41
• /
• 1986

A hybrid modelling technique of a soil-structure system on viscoelastic soil medium is studied in this paper. The hybrid model consists of a near-field and a far-field with their common interface passing through the soil region at some distance from the base of the structure. It makes use of frequency-dependent impedances so as to represent the semi-infinite far-field. The far-field impedances are formulate including the radiation damping characteristics as well as the viscoelastic properties of the soil medium. The verification of the method has been carried out using a rigid circular plate on a viscoelastic half-space. The impedances obtained by the method are compared with the theoretical values. Example analyses have been performed for a tall chimney and the results have been compared with those obtained by other methods which are frequently used.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.559-563
• /
• 2002

We measure the 3-dimensional temporal behavior of the light emitted from the discharge cell of a plasma display panel (PDP) by using a scanned point detecting system. The light signal detected by a PM tube is sent to the oscilloscope, and the oscilloscope is connected to a PC with GPIB. From the resultant temporal behaviors, we could analyze the discharge characteristics of the panel with a Ne-Xe (4%) mixing gas at a 400 torr pressure. The top view of the panel shows that discharge moves from the inner edge of the cathode electrode to the outer cathode electrode, forming an arc shape. The side view of the panel shows that the light is detected up to 150 $\mu\textrm{m}$ up the barrier rib. After a trigger pulse is applied, peak intensity is detected at 730 ns and peak intensity position is located at the center of the ITO electrodes.