• The Optical Journal
• /
• s.102
• /
• pp.52-55
• /
• 2006

본 고의 내용은 가공부의 분위기를 제어하고 가공장치 전체를 벨자(챔버)로 씌워 밀폐하고 그 안에서 가공하는 새로운 벨자형의 폴리싱 장치에 관한 것이다. 필자들이 고안, 시작한 밀폐 벨자형 폴리싱 장치는 벨자내에 각종 가스를 투입함과 동시에 일정 압력 하에서 또는 벨자내를 감압(진공)함으로서 가공부 전체의 분위기를 일정 조건으로 제어하는 것이 가능하다. 이 장치를 적용하여 다양한 가공환경 분위기 하에서 SiC와 사파이어 등의 어려운 가공 재료를 포함하는 각종 기능성 재료의 가공을 시험한 가공 특성을 소개함과 동시에 가공 메커니즘에 대해서 고찰하기로 한다. 한편, 본 원고의 번역에는 (주)그린광학의 김동균 부장이 도움을 주셨다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.6
• /
• pp.79-84
• /
• 2012

An experiment of rapid pressurization-induced crack propagation of solid propellant was conducted by using a windowed test chamber. A pre-cracked specimen of solid propellant is installed in the chamber, and highly compressed nitrogen gas in an accumulator pressurizes the chamber until the chamber pressure reaches set-up pressure to make the chamber depressurization. Pressure-time trace was obtained from the experimental result, and pressurization rate was defined from the trace. In this study, three pressurization rates (64.34, 73.86 and 85.44 MPa/s) are considered, and propagation lengths are measured. Also, a progression of the crack propagation recorded by a high-speed digital camera is presented.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.539-544
• /
• 2012

An experiment of rapid pressurization-induced crack propagation of solid propellant was conducted by using a windowed test chamber. A pre-cracked specimen of solid propellant is installed in the chamber, and highly compressed nitrogen gas in a accumulator pressurizes the chamber until the chamber pressure reaches set-up pressure to make the chamber depressurization. Pressure-time trace was obtained from the experimental result, and pressurization rate was defined from the trace. In this study, three pressurization rates (64.34, 73.86 and 85.44 MPa/s) are considered, and propagation lengths are measured. Also, a progression of the crack propagation recorded by a high-speed digital camera is presented.

• Journal of the Korea Society for Simulation
• /
• v.28 no.2
• /
• pp.1-14
• /
• 2019

A full scale hydrodynamic simulation that requires an accurate reproduction of shock-induced detonation was conducted for design of an energetic component system. A detailed hydrodynamic analysis SW was developed to validate the reactive flow model for predicting the shock propagation in a train configuration and to quantify the shock sensitivity of the energetic materials. The pyrotechnic device is composed of four main components, namely a donor unit (HNS+HMX), a bulkhead (STS), an acceptor explosive (RDX), and a propellant (BPN) for gas generation. The pressurized gases generated from the burning propellant were purged into a 10 cc release chamber for study of the inherent oscillatory flow induced by the interferences between shock and rarefaction waves. The pressure fluctuations measured from experiment and calculation were investigated to further validate the peculiar peak at specific characteristic frequency (${\omega}_c=8.3kHz$). In this paper, a step-by-step numerical description of detonation of high explosive components, deflagration of propellant component, and deformation of metal component is given in order to facilitate the proper implementation of the outlined formulation into a shock physics code for a full scale hydrodynamic simulation of the energetic component system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.311-316
• /
• 2018

As the lives of people have improved, the demand for improved indoor air quality has increased. Various methods are used to remove biological air pollutants, such as UV/photocatalytic devices and ozone generators. However, these methods have disadvantages such as energy consumption, high corrosivity and toxicity. To overcome these disadvantages, an antibacterial copper filter was fabricated and its antimicrobial activity was then tested against two fungi (P. pinophilum, C. globosum) and one bacteria (S. aureus) Moreover, the ability to remove suspended microorganisms was tested step by step from the chamber stage to the air conditioning system. The results revealed 100% antimicrobial activity after 24 hours for the two fungi, while this value was 99.9% after 18 hours for the bacteria. Moreover, the antibacterial activity was higher when the chamber and air purifier were used than was obtained using a general antibacterial HEPA filter. Also, as a filter for system air conditioner, the antibacterial activity was lowered in offices and hospitals. In conclusion, the copper filter was found to have sufficient antibacterial activity for use as an antibacterial filter; however, further research on its preparation methods and materials is warranted.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.39-48
• /
• 2017

In this study, combustion modeling of ZPP and $BKNO_3$ mainly used in the PMD industries has been performed. Saint Robert's law, energy conservation equation, and the Noble-Abel equation of the state have been used for governing equations. The results of pressure obtained from established combustion models and actual CBT have been compared. In the case of ZPP, the model has predicted a pressure curve similar to that of the experimental results, but $BKNO_3$ has showed that the maximum pressure of the model is greater than the experiment at small chamber volume. For these gaps, the probability of $BKNO_3$ unburning has been considered.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.5
• /
• pp.732-744
• /
• 2020

In this study, a torrefaction of Quercus serrata to manufacture a molded charcoal was performed, investigated material properties, fuel characteristics, and performed a quantitative analysis of hazardous gases which occur during a combustion process. In addition, a molded charcoal in market was selected as a control group, and a comparative analysis was performed. As a result, the higher heating value (HHV) of the torrefied specimen was about 14% higher than that of molded charcoal, and its ash content was about 51 times lower. Moreover, after performing a quantitative assessment of hazardous gases (carbon monoxide, nitrogen oxide, and sulfur dioxide) which were produced when each specimen was combusted for 900 seconds in an enclosed chamber, it was confirmed that the maximum value of generated amount of carbon monoxide on the torrefied specimen was about 50 times lower than that of the existing molded charcoal. Therefore, it was shown that the torrefied specimen produced in this study had a higher heating value than the molded charcoal in the market, and a very low amount of carbon monoxide generated during the combustion process.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.973-978
• /
• 2010

The emission of volatile organic compounds (VOCs) from building materials is one of great concerns due to maintain airtight condition of a building to reduce energy consumption, and it causes the deterioration of indoor air quality. Therefore, the emission characterization of VOCs from building materials is necessary to improve indoor air quality. Emission characteristics of VOCs from a plywood flooring that is one of the most commonly used materials in an under-heating system, and from an adhesive that is generally used to stick a plywood flooring to a concrete floor were investigated using an emission chamber test in this study. It was found that the VOCs emission factor was dependent upon and proportional to indoor temperature, and the emission characteristics were closely related to the existing places and conditions of VOCs sources inside the building materials. Maximum emission factors of hexane and toluene from building materials were generally observed at the beginning, however, only that of toluene from a plywood flooring was shown after 6 hours from the beginning. It could be considered that the existing place and condition of toluene source inside a plywood flooring could influence on the VOCs emission. From this study, bake-out time more than 72 hours could be recommended before moving in to avoid the exposure to high concentration of VOCs emitted from an under-heating system.

• Fire Science and Engineering
• /
• v.16 no.1
• /
• pp.18-23
• /
• 2002

Efficiency estimation of toxicity free resistance cable experiments were conducts to understand toxicity free fire ersistance polyolefin insulation material and smoke density characteristic and combustion gas corrosion analysis. A main cause of fire-growth and generating toxic gas when it burns, should be dealt with great care in life safety design. Similar patterned fire incidents such as, Inchon Live-Hof Pub Restaurant as, Sea-land Children Resort have proven that serious loss of lives were caused by hazardous gas generated fire resistance cable materials. In this paper, Referenced documents were ASTM E662 standard test method for specific Ds genalated by solid materials. The furnace control system shall maintain the required irradiance level under steady-state condition with the chamber door closed of 2.5$\pm40.04〔w/$\textrm{cm}^2$〕for 20 min. According to the results of the smoke density analysis of NFR-8 and FR-PVC the highest decomposition flaming smoke density range of NFR-8 and FR-PVC were 25.2 to 37.5 and 51.1 respectively. Nonflaming smoke density range of NFR-8 and FR-PVC were 100.4 to 112.2 and 126.5 to 398.8. Also, the fire gases was occurred carbon monoxide and decomposition than in polyolefin due to incomplete combustion of PVC which has high content of carbon in chemical compound.