• Journal of the Korea Concrete Institute
• /
• v.21 no.5
• /
• pp.589-597
• /
• 2009

High Performance Fiber-reinforced Cement Composite (HPFRCC) shows the multiple crack and damage tolerance capacity due to the interfacial bonding of the fibers to the cement matrix. For practical application, it is needed to investigate the fractural behavior of HPFRCC and understand the micro-mechanism of cement matrix with reinforcing fiber. This study is devoted to the investigation of the AE signals in HPFRCC under monotonic and cyclic uniaxial compressive loading, and total four series were tested. The major experimental parameters include the type and volume fraction of fiber (PE, PVA, SC), the hybrid type and loading pattern. The test results showed that the damage progress by compressive behavior of the HPFRCC is a characteristic for the hybrid fiber type and volume fraction. It is found from acoustic emission (AE) parameter value, that the second and third compressive load cycles resulted in successive decrease of the amplitude as compared with the first compressive load cycle. Also, the AE Kaiser effect existed in HPFRCC specimens up to 80% of its ultimate strength. These observations suggested that the AE Kaiser effect has good potential to be used as a new tool to monitor the loading history of HPFRCC.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.2
• /
• pp.77-83
• /
• 2006

Ultrasonic nonlinearity has been considered as a solution for the detection of microcracks or interfacial delamination in a layered structure. The distinguished phenomenon in nonlinear ultrasonics is the generation of higher-order harmonic waves during the propagation. Therefore, in order to quantify the nonlinearity, the conventional method measures a parameter defined as the amplitude ratio of a second-order harmonic component and a fundamental frequency component included in the propagated ultrasonic wave signal. However, its application In field inspection is not easy at the present stage because no standard methodology has yet been made to accurately estimate this parameter. Thus, the aim of this paper is to propose an advanced signal processing technique for the precise estimation of a nonlinear ultrasonic parameter, which is based on power spectral and bispectral analysis. The method of estimating power spectrum and bispectrum of the pulse-like ultrasonic wave signal used in the commercial SAM (scanning acoustic microscopy) equipment is especially considered in this study The usefulness of the proposed method Is confirmed by experiments for a Newton ring with a continuous air gap between two glasses and a real semiconductor sample with local delaminations. The results show that the nonlinear parameter obtained tv the proposed method had a good correlation with the delamination.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1711-1715
• /
• 2007

하천에서는 나라마다 하천마다 구간마다 독특한 하도특성을 지니고 있다. 우리나라는 전 국토의 70 %가 산지로 이루어져 있으며, 이로 인하여 특이한 하도형태의 모습을 보이는 구간이 산재하고 있다. 그 대표적인 모습이 충적하도와 침식하도가 연속해 발생하는 과정에서 나타나는 것이 하천 협착부 구간이다. 이러한 하천협착부 주변지역은 전형적인 수해상습 구간이 되는 경우가 많다. 이러한 상황임에도 불구하고 현재까지 우리 나라에서는 이러한 협착부 구간에서 하도특성을 반영한 연구 및 설계 사례가 전무한 실정이다. 따라서, 본 연구에서는 낙동강 선산지역의 하천 협착부에서의 하도 수리학적 의미와 하도형태에 대하여 조사하고 분석하였다. 연구 결과, 모래하천인 조사구간의 저수로 하상에서 아주 미세한 유사분급 현상은 확인할 수 있었지만, 명쾌한 자연 영력에 의한 유사분급 현상이라 판단하기에는 어려운 부분이 있었다. 이는 완만한 하상경사, 균일성에 가까운 하상재료의 공급에 기인한다고 추정할 수 있었다. 그러나 이와 같은 자연적인 현상보다는 골재채취 등의 원인에 따른 유사분급이 확연하다고 추정되었다. 그리고 협착부의 배수구역에서 과거 활발했던 이동상 단단면 하도형태가 유심부의 이동과 더불어 최근 급격하게 복단면화가 진행되고 있음을 확인하였다. 이와 더불어 저수로의 하폭이 크게 줄어드는 현상을 확인할 수 있었다. 이와 같은 현상은 궁극적으로 이상홍수 발생시의 복단면 가중 또는 홍수단면적 축소, 저수로에서의 호안 또는 제방 아래부분의 국소세굴이 야기될 수 있음을 시사한다.원주교각에 대한 국부세굴 특성을 검토하였다. 또한 원주형의 교각에서는 단일원주보다는 원주군으로 설치되는 경우가 대부분이며 이때 교각의 직경(D)에 대한 교각 사이 간격$(L_d)$의 비$(L_d/D)$에 따른 전면교각에서의 수류변화의 영향이 후면교각에 작용하여 상호 복합적인 흐름 및 세굴특성을 나타내므로 이와 같은 복렬형 원주군의 세굴특성을 파상형 원주교각에 적용하여 국부세굴의 크기 변화를 해석하였다. 따라서, 교각주위에서의 수류특성 및 세굴의 변동은 원주군 및 교각파상의 크기와 간격 등과 같은 구조물의 배열조건과 Froude 수, 수심 등의 수리학적 조건에 따라 달라지므로 이의 조건을 체계적으로 변화시켜 가면서 교각주위에서의 국부세굴 및 세굴 감소특성을 검토하였다. 실험결과 오목 및 볼록 파상형 원주 주위에서의 세굴크기는 원형원주와 비교하여 전체적으로 감소하는 것으로 확인되었으며 특히 오목형 $B/\acute{h}=3$에서는 세굴경감효과가 탁월하여 70%이상 감소하는 것으로 확인되었으나 볼록형 $B/\acute{h}=5$에서는 세굴촉진특성이 나타나고 있는 것으로 나타났다. 따라서, 파상형 원주에서는 하강류나 와류를 파상형의 내부로 유도하여 세굴의 크기를 조절할 수 있는 최적의 파상이 존재하고 있는 것으로 예측되었다.원 분야 소프트웨어의 개발에 기본 토대를 제공할 것으로 판단된다.았다. 또한 저자들의 임상병리학적 연구결과가 다른 문헌에서 보고된 소아 신증후군의 연구결과와 큰 차이

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.87-92
• /
• 2003

$Ti_3AlC_2$was synthesized from TiCx and Al powder as a starting materials at the temperature range between$800^{circ}C;and;1500^{\circ}C$. The vacuum sintering and hot pressing methods were imployed to synthesize$Ti_3AlC_2$. The high purity$Ti_3AlC_2$was synthesized using TiCx and Al powder as starting materials without formation of Ti-Al intermetallic compound and Al-C compound.$Ti_2$AlC and$Ti_3AlC_2$were preferentially synthesized at$800^{\circ}C$and above$1200^{\circ}C$, respectively.$Ti_2$AlC formed at low temperature was transformed to$Ti_3AlC_2$by further reaction with TiC. In this study, the synthesis mechanism for$Ti_3AlC_2$was proposed. The synthesized$Ti_3AlC_2$showed the nano laminating structure consisting of$Ti_3AlC_2$crystal with the thickness of 45~120 nm.

• Journal of the Korean Magnetics Society
• /
• v.18 no.3
• /
• pp.120-125
• /
• 2008

In this study, NiCoZn ferrites with the variation of sintering temperature and chemical composition were prepared by the coprecipitation. Microstructures Crystal structure of NiCoZn ferrites were analyzed by XRD and their electric magnetic characteristics were analyzed by LCR meter and their morphology observed by SEM. We identified that these powders have a typical NiCoZn spinel structure and nanoparticles average size of 40 nm. The impurity, the initial permeability and the Q factor value are the lowest of sintered NiCoZn ferrite at $1250^{\circ}C$. Also, we measured S-parameter for $(Ni_{0.4}Co_{0.1}Zn_{0.5})Fe_2O_4$ which showed a maximum reflection loss of -3.1 dB at 6 GHz for the 2 mm thick sample. From this result, we found that the NiCoZn ferrite can be used in ferrite microwave-absorbing application at a higher frequency region (> 6 GHz).

• Journal of the Korean Magnetics Society
• /
• v.9 no.2
• /
• pp.78-84
• /
• 1999

$(Ni, Zn)Fe_2O_4$ powders were prepared through self-propagating high temperature synthesis reaction and the effects of initial zinc oxide powder size and oxygen pressure on the magnetic properties of the final combustion products were studied. The ferrite powders were combustion synthesized with iron, iron oxide, nickel oxide, and zinc oxide powders under various oxygen pressures of 0.5~10 atmosphere after blended in n-hexane solution for 5 minutes with a spex mill, followed by dried at 120 $^{\circ}C$ in vacuum for 24 hours. The maximum combustion temperature and propagating rate were about 1250 $^{\circ}C$ and 9.8 mm/sec under the tap density, which were decreased with decreasing ZnO size and oxygen pressure. The final product had porous microstructure with spinel peaks in X-ray spectra. As the ZnO particle size in the reactant powders and oxygen pressure during the combustion reaction increase, coercive force, maximum magnetization, residual magnetization, squareness ratio were changed from 1324 Oe, 43.88 emu/g, 1.27 emu/g, 0.00034 emu/gOe, 37.8$^{\circ}C$ to 11.83 Oe, 68.87 emu/g, 1.23 emu/g, 0.00280 emu/gOe, 43.9 $^{\circ}C$ and 7.99 Oe, 75.84 emu/g, 0.791 emu/g, 0.001937 emu/gOe, 53.8 $^{\circ}C$ respectively. Considering the apparent activation energy changes with oxygen pressure, the combustion reaction significantly depended on initial oxygen pressure and ZnO particle size.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.2
• /
• pp.235-244
• /
• 2020

This study conducted a series of studies to offer a novel method of using CBS-dust that produced as by-product in the manufacture of cement. Four different contents of BS and CBS-dust were adopted for test parameters of this study. Mortar with 50% of W/B was fabricated. First, in the case of the fresh mortar, the flow decreased as the CBS-dust replacement rate increased, but the binder composition ratio BS 45% and 65% showed higher fl ow than Pl ain when repl acing CBS-dust 5%. In the case of air content, overall, the tendency was proportional to the CBS-dust replacement rate, and chloride tended to exceed the reference value at all replacement rates except for the CBS-dust 0% replacement. The compressive strength of the hardened mortar shows the resul t that the strength is improved when the CBS-dust is repl aced by 5% to 10%, and the CSH gel and structure formation is confirmed by microstructure analysis through the hydration reaction when the CBS-dust is replaced. Therefore, for a given condition CBS-dust is used as a early-strength admixture in a concrete secondary product that uses a large amount of admixture without reinforcing bars it can be an effective method for enhancing the strength of concrete as an alkali activator.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.265-273
• /
• 1999

Various oxide films are commonly used as a sacrificial layer or etch mask in the fabrication of microelectromechanical systems (MEMS). Large residual strain of these oxide films causes the wafer to bow, which can have detrimental effects on photolithography and other ensuing processes. This paper investigates the residual strain of tetraethoxysilane (TEOS), low temperature oxide (LTO), 7 wt% and 10 wt% phosphosilicate glass (PSG). Euler beams and a bent-beam strain sensor are used to measure the residual strain. A poly silicon layer is used as the sacrificial layer, which is selectively etched away by $XeF_2$. First, the residual strain of as-deposited films is measured, which is quite large. The residual strain of the films is also measured after annealing them not only at $500^{\circ}C$, $600^{\circ}C$, $700^{\circ}$ and $800^{\circ}C$ in $N_2$ environment for 1 hour but also at the conditions for depositing a $2\;{\mu}m$ thick polysilicon at $585^{\circ}C$ and $625^{\circ}C$. Our results show that the 7 wt% PSG is best suited as the sacrificial layer for $2\;{\mu}$ thick polysilicon processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.436-444
• /
• 2013

This article presents the dynamic response of nano-scale plates using the nonlocal continuum theory and higher-order shear deformation theory. The nonlocal elasticity of Eringen has ability to capture the small scale effects and the higher-order shear deformation theory has ability to capture the quadratic variation of shear strain and consequently shear stress through the plate thickness. The solutions of transient dynamic analysis of nano-scale plate are presented using these theories to illustrate the effect of nonlocal theory on dynamic response of the nano-scale plates. The relations between nonlocal and local theories are discussed by numerical results. Also, the effects of nonlocal parameters, aspect ratio, side-to-thickness ratio, size of nano-scale plate and time step on dynamic response are investigated and discussed. The amplitude and cycle increase when nonlocal parameter increase. In order to validate the present solutions, the reference solutions are used and discussed. The theoretical development as well as numerical solutions presented herein should serve as reference for nonlocal theories as applied to the transient dynamic analysis of nano-scale structures.

• Korean Journal of Materials Research
• /
• v.10 no.10
• /
• pp.684-690
• /
• 2000

In order to study effects of interfacial layers between $Pb(Zr,Til)Q_3(PZT)$ films and electrodes for Metal-Ferroelectric-MetaI(MFM) structure capacitors, we have fabricated the capacitors with the Pt/PZT/interfacial-layer/Pt/$TiO_2/SiO_2$/Si structure. $PbTiO_3(PT)$ interfacial layers were formed by sol-gel deposition and PbO, ZrO, and $TiO_2$ thin layers were deposited by reactive sputtering. $TiO_2$ interface layers result in the finest grains of PZT(crystalline Temp. $600^{\circ}C$) films compare to $PbO_2\;and\;ZrO_2$ layers. However, as the thickness of $TiO_2$ layer increases. PZT thin films become rough and electrical characteristics were deteriorated due to remained anatase phase. On the other hand. PT interface layers result in improved morphology of PZT films and do not significantly change ferroelectric properties. It is a also observed that seed layers at the middle and top of PZT films do not give significant effects on grain size but the PT seed layer at the interface between the bottom electrode and the PZT films results in the small grain size.