• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1998.11a
• /
• pp.105-108
• /
• 1998

Dust explosion은 combustible solid의 미세한 입자가 공기 혹은 산소중에서 폭발범위의 농도에서 부유할 때 화염 혹은 spark 등의 에너지 공급에 의해 폭발하는 현상이며 plastic 공업, 금속분말, 유기약품, 무기약품, 안료, 농수산건조물 등에서 분체취급 분야의 확대 및 취급량의 증가에 따라 분진폭발의 잠재 위험성이 급증하고 있어 화학적 성질, 농도, 입경, 폭발 압력 등의 분진특성과 함께 분진폭발의 착화온도와 상한 및 하한 농도에 대해 이론 및 실험적으로 광범위하게 연구가 진행되어져 왔다. (중략)

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.05a
• /
• pp.61-64
• /
• 2002

Dust explosion은 combustible solid의 미세한 입자가 공기 혹은 산소중에서 폭발범위의 농도에서 부유할 때 화염 혹은 Spark 등의 에너지 공급에 의해 폭발하는 현상이며 plastic 공업, 금속분말, 유기약품, 무기약품, 안료, 농수산건조물 등에서 분체취급 분야의 확대 및 취급량의 증가에 따라 분진폭발의 잠재 위험성이 급증하고 있어 화학적 성질, 농도, 입경, 폭발 압력 등의 분진특성과 함께 분진폭발의 착화온도와 상한 및 하한 농도에 대해 이론 및 실험적으로 광범위하게 연구가 진행되어져 왔다.(중략)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1051-1060
• /
• 2010

The effect of materials on fuel coolant interactions (FCIs) was analyzed on the basis of a solidified particle size response for TROI experiments.$^{(1)}$ The solidified particle size response can provide an understanding of the relationship among the initial condition, the mixing, and an explosion. Through a comparison of the size distributions of the solidified particles in the case of explosive and non-explosive FCIs, it is revealed that an explosive FCI results in the production of a large amount of fine particles and a small amount of large particles. The material effect of the size of solidified particles was analyzed using non-explosive FCIs without losing the information on the mixing. This analysis indicates that an explosive melt includes large particles that participate in the steam explosion, whereas a nonexplosive melt includes smaller particles and finer particles.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.6
• /
• pp.813-822
• /
• 1998

The microexplosion of a slurry droplet was considered to be caused by the shell formation and the following pressure build-up in the shell which would be promoted by the suppression of evaporation, subsequent superheating and heterogeneous nucleation of liquid carrier. To closely investigate the pressure build-up and the heterogeneous nucleation, a numerical model was introduced by considering the internal temperature distributions with the shell formation, suppression of evaporation and pressure build-up inside. The microexplosion time was estimated by postulating the limit of superheat for heterogeneous nucleation. The simulation yielded a reasonably good agreement with experimental results for Al/n-heptane slurry droplets under various solid loadings.

• 방재와보험
• /
• s.69
• /
• pp.42-43
• /
• 1996

• Fire Science and Engineering
• /
• v.13 no.2
• /
• pp.26-32
• /
• 1999

We had investigated combustion pro야$\pi$ies of rice bran dusts. Decomposition of rice bran d dusts with temperature were investigated using DSC and the weight loss according to t temperature using TGA in order to find the thermal hazard of rice bran dusts, and the p properties of dust explosion in variation of their dust with the same particle size. Using H Hartman's dust explosion apparatus which estimate dust explosion by electric ignition after m making dust disperse by compressed air, dust explosion experiments have been conducted by v varying concen$\sigma$ation and size of rice br뻐 dust. According to the results for thermodynamic stability of rice bran dust, there are little change of initiation temperature of heat generation 때d heating value for used particle size. But i initiation temperature of heat generation decreased with high heating rate whereas d decomposition heat increased with particle size. Also, the explosion pressure was increased as t the ignition energy increased and average maximum explosion pressure was 13.5 kgv'cnt for 5 BJ/60 mesh and 1.5 뼈Ie미 dust concentration.

• Fire Science and Engineering
• /
• v.12 no.2
• /
• pp.61-68
• /
• 1998

According to the results for the thermodynamic stability of feed-stuff dust, there are little change of initiation temperature of heat generation and heating value for used particle size. But initiation temperature of heat generation decreased with high heating rate whereas decomposition heat increased with particle size. Using the supporting gas, O2, initiation temperature of heat generation decreased remarkably than using the inert gas, N2, and heating value increased as twenty times under the same condition. When the ignition energy is given from the outside, used fine particle which can float in the air easily reacted tremendously with oxygen. Average maximum explosion pressure was 6.88 Kgf/$\textrm{cm}^2$ for 80/100 mesh.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.17-17
• /
• 2003

선폭법[전기선 폭발 법, Electrical Explosion of wire(EEW)]은 $10^{10A}$$m^2$ 이상의 고밀도 전류를 금속와이어에 인가하여 순간적으로 폭발시키는 기술로서 고밀도 대 전류가 금속와이어를 통과할 때, 저항발열에 의해 와이어가 미세한 입자나 금속증기 형태로 폭발하는 현상을 이용하여 나노분말을 합성하는 방법으로 나노 금속분말 뿐만 아니라 분위기 제어에 의한 산화물, 질화물, 탄화물 및 합금분말 둥 다양한 분말을 제조할 수 있는 장점이 있다. 또한 다른 제조법에 비해 양산화에 가장 근접한 기술로 알려져 있으며, 러시아가 세계적 기술수준으로 가장 앞선 것으로 알려져 있으며, 미국, 독일 및 일본 둥에서 1995년 이후 선폭 기술을 이용하여 나노분말 제조를 산업화하였다.다.

• Journal of Energy Engineering
• /
• v.10 no.2
• /
• pp.153-160
• /
• 2001

본 연구에서는 고온 분위기 온도 및 대기압 하에서 액적의 급속가열과 연소가 가능한 고온 연소로 장치와 고속도 비디오 카메라를 이용하여 다조성 단일 액적 연소에 대해 고찰하였다. 그 결과 저비점 성분을 혼합한 경유의 액적은 기본적으로 입경의 2승 법칙에 의해서 감소되었으며, 그 과정에서 입경이 일시적으로 급속히 감소하는 현상이 보여짐과 더불어 연소기간도 단축되었다. 즉, 저비점 성분을 혼합한 경유의 액적은 미세폭발 현상에 의해 기존 디젤 연료에 비해 더 빨리 증발되고 연소가 되었다. 또한, 순수 파라핀계 및 함산소계 연료의 화염은 전체 연소기간동안 기존 경유의 화염에 비해 푸른색을 띠고 있어, 매연이 없는 연소를 입증해 주었다.

• Journal of Korean Society of Disaster and Security
• /
• v.16 no.1
• /
• pp.61-70
• /
• 2023

This study presents an analytical study of investigating the effect of shock waves generated by the hydrogen detonation and damage to structures for the safety evaluation of hydrogen storage facilities against detonation. Blast scenarios were established considering the volume of the hydrogen storage facility of 10 L to 50,000 L, states of charge (SOC) of 50% and 100%, and initial pressures of 50 MPa and 100 MPa. The equivalent TNT weight for hydrgen detonation was determined considering the mechanical and chemical energies of hydrogen. A hydrogen detonation model for the converted equivalent TNT weight was made using design equations that improved the Kingery-Bulmash design chart of UFC 3-340-02. The hydrogen detonation model was validated for overpressure and impulse in comparison to the past experimental results associated with the detonation of hydrogen tank. A parametric study based on the blast scenarios was performed using the validated hydrogen detonation model, and design charts for overpressure and impulse according to the standoff distance from the center of charge was provided. Further, design charts of the three-stage structural damage and standoff distance of adjacent structures according to the level of overpressure and impact were proposed using the overpressure and impulse charts and pressure-impulse diagrams.