• 소성∙가공
• /
• 제27권4호
• /
• pp.244-249
• /
• 2018

Rhodium is a representative platinum group material. Rhodium is used in several industrial fields including jewelry, chemical reaction catalyst, electric component etc. In recently, ultra-fine rhodium wire has been applied to the pins of probe card used to test a semiconductor. In this study, in order to produce a fine rhodium wire with the diameter of $50{\mu}m$, a fine rhodium wire drawing process was designed. After design of the fine wire drawing process by using a uniform reduction ratio theory, finite element analysis was performed. Finally, fine wire drawing experiment was performed to verify the effectiveness of the designed process.

• 소성∙가공
• /
• 제15권1호
• /
• pp.65-70
• /
• 2006

In recent industry, with the miniaturization and high-precision of machine part, the development of mold manufacturing technology for mass production is accompanied by the development of new technology such as IT and BT In this study, the spiral type injection mold with a $200{\mu}m$ thickness is made to. investigating the influence of injection molding parameter and the flow length is measured through an experiment. Besides, Taguchi method is used in this experiment and the obtained data are analyzed using ANOVA method.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.25-28
• /
• 2000

The flow stress of 304 stainless steel during high during hot forming process were determined by conducting hot compression tests at the range of 1273 K-1423 K and 0.05 /s-2.0 /s as these are typical temperature and strain rate in hot forging operation. Based on the observed phenomena, a constitutive model of flow stress was assumed as a function of strain, strain rate, temperature. Dynamic recrystallization was found to be the major softening mechanism with this conditions as previous studies. A finite element analysis was performed to predict the recrystallized volume fraction and the mean grain size in hot compression of 304 stainless steel.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.21-24
• /
• 2000

Ultra-fine grains were produced in pure Al using an Accumulative Rolling-Bonding (ARB) process. After several cycles of the ARB process, pure Al sheets were filled with the ultra-fine grains whose diameters were several hundred nano-meters. With ARB cycles, the nature of grain boundaries of the ultra-fine grains changed from diffusive sub-boundaries to well-defined high angle boundaries. After 7 cycles, ultra-fine polycrystals with large misorientations between neighboring grains were obtained. Sliding wear tests using a pin-on-disk type wear tester were co ducted on the ultra-fine grained pure Al. Wear rates of pure Al increased with the increase of ARB cycle numbers in spite of the increase in hardness. Worn surfaces and cross-sections were examined with optical microscopy (OM) and scanning electron microscopy (SEM) In investigate the wear mechanism of the ultra-fine grained pure Al.

• 소성∙가공
• /
• 제10권7호
• /
• pp.573-578
• /
• 2001

The flow stress of 304 stainless steel during hot forming process were determined by conducting hot compression tests at the range of 1273 K∼1423 K and 0.05 /s∼2.0 /s as these are typical temperature and strain rate in hot forging operation. In this material, Dynamic recrystallization was found to be the major softening mechanism with this conditions as Previous studies. Based on the observed phenomena, a constitutive model of flow stress was assumed as a function of strain, strain rate, temperature. In the constitutive model, the effects of strain hardening and dynamic recrystallization were taken into consideration. A finite element method connected to constitutive model was performed to predict the dynamic recrystallization behaviors and also stress-strain curves in hot compression of 304 stainless steel.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.166-169
• /
• 2004

Permalloys were successfully fabricated by melt drag casting in the present study, and their variation of microstructure and consequent magnetic properties were investigated as a function of Si contents and annealing temperature. The increases in Si content and annealing temperature resulted in the increases of grain size and amount of $FeNi_3$ ordered phase. Both the grain size and $FeNi_3$ ordered phase controlled by Si and annealing temperature had a important role on permeability of permalloys.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.409-412
• /
• 2004

Microstructures and mechanical properties of microalloyed cold forging steel and cold forged prototype automobile part are characterized. The work hardening according to the increase of plastic strain plays a major role in increasing the tensile strength of microalloyed cold forging steel during cold forming. On the other hand, inhomogeneous distribution of plastic strain causes variations in microstructure and mechanical properties. The relation between inhomogeneous distribution of plastic strain and variations in microstructure and mechanical properties is discussed. The variation of mechanical property in cold forged automobile part is analyzed using quantitative evaluation of plastic strain from finite element method.

• 소성∙가공
• /
• 제6권5호
• /
• pp.435-445
• /
• 1997

In order to study the manufacturing possibility of connecting rod by direct quenching method, the difference between connecting rod by direct quenching and that by general heat treatment were investigated by observing microstructure, by measuring mechanical properties, by conducting fatigue testing, and by measuring the amount of tool wear in actual cutting. Connecting rod manufactured by direct quenching had better fatigue life than that by general heat treatment, which was due to homogeneous microstructure, and higher strength. The amount of cutting tool wear of connecting rod by direct quenching was higher than that by general heat treatment, which was due to low machinability and high toughness of tempered martensite microstructure. Therefore it will be added the study of heat treatment and cutting condition for manufacturing by direct quenching.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.251-253
• /
• 2006

본 연구에서는 Anodic Aluminum Oxide(AAO) 템플레이트 제조 시 알루미늄의 결정방위가 세공 형성에 미치는 영향을 연구하였다. 시료는 직경 20mm 두께 2mm의 세가지 단결정 시편을 사용 하였으며 이는 XRD 장비로 $2{\theta}$ 측정결과를 통해 확인 하였다. 양극 산화전 평활한 면을 얻기 위해 다이아몬드분말로 미세연마하였으며 양극산화는 세가지 시편 모두 동일한 조건에서 2단계공정까지 진행하여 반복 실험 하였다. 결과는 전계방출주사전자현미경(FE-SEM)으로 표면의 세공형태를 관찰 하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.215-218
• /
• 2006

A study was made to investigate microstructural evolution and mechanical properties of ultra-fine grained (UFG) pure-Ti produced by equal channel angular (ECA) pressings. The deformed structures were analyzed by finite element method and transmission electron microscopy with the increment of straining. After 4 isothermal ECA pressings, initial coarse grains ($30{\mu}m$) were significantly refined to ${\sim}0.3{\mu}m$ with homogeneous distribution of microstructure which was resulted from $180^{\circ}$ rotation of the sample between pressings. UFG pure-Ti exhibited the considerable improvement in yield strength while losing strain hardening capacity as compared to coarse grained microstructure at ambient temperature, which was mainly attributed to ultra-fine grain microstructure with non-equilibrium grain boundaries.