• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.8
• /
• pp.41-47
• /
• 2017

With the introduction of new technologies, ground weapons have led to the development of artificial intelligence and the attention of major developed countries. In this study, CFD was performed through the BLU-103 model to obtain aerodynamic data for aircraft that are subjected to rotational motion. To simulate the steady-state of a rotating body, the body was fixed and the principle of rotating the body by rotating the surrounding air was used. In order to examine the aerodynamic feasibility of the rotating aircraft, the analysis was carried out at intervals of $30^{\circ}$ angle from $0^{\circ}$ to $90^{\circ}$ for the simple shape and the side slip angle. It was confirmed that the drag coefficient for the simple model satisfies the quantitative results of 1.0 ~ 1.2 through CD presented in "Drag Book". The aerodynamic data was constructed by applying the valid input verified through the simple type analysis conditions to the actual shape, and the tendency was analyzed. The analysis confirmed that CX, CZ and CY increase not only in the simple model but also in the rotation of the actual model. Especially, the influence of CZ was judged to have contributed to the flight.

• Journal of Korean Society of Transportation
• /
• v.29 no.3
• /
• pp.31-40
• /
• 2011

Generally, inappropriate driving conditions including geometric, traffic environmental, and driver psychological problems may be critical reasons of traffic accidents. Under this circumstance, various types of facilities have been installed to improve traffic safety by itself or as a set consisting of several other traffic safety facilities. In general, traffic accidents occur by several reasons combined rather than only a single reason, and thus the safety effect of the safety facilities cannot be simply analyzed with only a single improvement. For the study, traffic accident data on the roadway segments of interest are collected along with field survey data. For the analysis, various alternative analysis methods were evaluated in terms of assessing accident reduction from various types of traffic safety improvements. Among the alternative methods tested including simple before-and-after evaluation method, before-and-after evaluation yoked comparison, and Comparison Group (C-G) method, it was found that the C-G method is the most effective method for analyzing the traffic safety improvement effect. Adopting the C-G method, both single and multiple safety improvements were analyzed. The results from this study can potentially be applied to decide the best type of treatments to improve traffic safety as well as to measure the accident reduction effects from the treatments.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.6
• /
• pp.397-405
• /
• 2012

Installation of deck has been on the rise in Korea recently, but there is little of research on the safety of deck. One of the major factors affecting maneuverability of a pedestrian is frictional force between an outsole of shoe and a surface of the deck. The frictional force is influenced by many factors such as raw material variance of deck, surface convex shape of deck, outsole patterns of shoes, and moist condition of contact surface between deck and shoes. This study focused on evaluating the effect of these factors on the frictional force. Two kinds of deck, which were made of natural wood and wood plastic composite, were used in this study. The surface convex patterns of deck were classified to single nonslip (longitudinal groove processing) and double nonslip (longitudinal and transverse groove processing). Two kinds of shoe outsole patterns, W-shape and rectangle-shape, were used in the tests. Also, the friction tests were carried out at dried surface conditions and water-adsorbed surface condition.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.1
• /
• pp.109-117
• /
• 2016

This paper is focused on the determination of friction parameter which is a predominant factor in the design of inflatable structure system. This inflatable structure system is very valuably used to protect passively and rapidly the possibilities of tunnel damages by flooding threats and unusual leakage to be occurred during and after underground infrastructure construction. In particular, this system should be necessary in subsea tunnel. This study presents the experimental results obtained from the relative friction characteristics tests of the fabric materials that constitute the inflatable structure. In order to evaluate the relative friction behaviour of the inflatable structure system, friction tests and scaled model tunnel friction tests are carried out. The friction tests are carried out to determine the friction coefficient for different surface conditions between tunnel and inflatable structure. These friction coefficients are then evaluated and compared with the result obtained from the model tunnel friction tests. Interaction behaviours between tunnel and system are also reviewed and described in this study. The results clearly show that the friction coefficients derived from scaled model slippage tests are about 12% lower than values obtained from the friction tests. In addition, this study will be necessary to verify the real friction behaviour with prototype tests before applying in practice.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.9-16
• /
• 2010

Roughness is the most important factor to maintain the road performance, and affects greatly on the design life in Jointed Plain Concrete pavements. Also, the factors the evaluate pavement‘s commonality is the three method such as functionality, safety and structural performance. In evaluating function of road, representative factors is the roughness, which has been used to determine maintenance time as key standard. As research for roughness is absence in pavement design. Applied roughness-model had a low-reliability in Korea. Therefore, it is needed to develop reliable model in road roughness. In this research, uniform specific is applied to distribute them after selecting the concrete pavements. Concrete pavement is divided by sections of 238. Total length of this sections has 281km and account for 16% of total road length in korean concrete pavements for selected sections. Considering the korean roughness-model, the evaluation of roughness is performed for the freezing index, average annual rainfall, condition for the base, the amount of traffic as well as spalling(%), cracking(%), age(year) at the selected section at the selected section. Also, additional sections is selected to evaluate various age which affects on the roughness. As a result of the analysis, it showed that spalling(%), cracking(%), age(year), and the condition of the base affected road roughness. When the correlation with the road roughness was analyzed, the reliable model for road roughness was proposed, and the ratio that can explain road roughness was R2-68.8% and P value-0 which is statistically meaningful.

• The Journal of the Petrological Society of Korea
• /
• v.7 no.1
• /
• pp.53-68
• /
• 1998

Microstructural and rock structural analyses on the deformed Cheongsan granite characterized by abundant K-feldspar megacrysts have been carried out to understand the temperature condition for the ductile shear deformation. In K-feldspar, microkinks, microfractures and core-and-mantle structures without the development of subgrains in outer core-zone are the most common microstructures observed. Myrmekites and flame perthites are developed at the strain-localized areas along the microfractured K-feldspar. In plagioclase, microfractures, deformation twins and kink bands are predominant. The deformation twins cut across the igneous zonation of the plagioclase. Patterns of c-axis fabrics of dynamically recrystallized new quartz grains display single girdle and type II crossed girdle where prism slip system is predominant. These characteristic microstructures produced during the ductile shearing suggest that the ductile shear deformation in the Cheongsan granite occurred under epidote-amphibolite conditions($400-500^{\circ}C$). Three main shear zones are recognized at outcrop scale: discrete shear zone with anastomosing high-strain domain, shear zone with pervasive S-C structure and shear zone with homogeneously foliated domain. Geometric features of these shear zones produced during the ductile shear deformation are controlled by amount of strain under the $400-500^{\circ}C$ deformation temperature.