• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.7-12
• /
• 1997

The wear behavior of SiC in SiC-steel sliding couple was investigated under various wear test conditions, such as solid state sliding - dry and wet air atmosphere - or lubricated sliding, sliding velocity and at-mosphere temperature. The effect of SiC fabrication process on the SiC wear rate was also studied under varying sliding velocities. Humidity of air plays a lubricating role in the solid state sliding, while the wear behavior is largely influenced by the sliding velocity, especially if the atmosphere is extremely dry. The fa-brication process of SiC and the surface roughness result in different wear rate depending on the magnitude of sliding velocity. High temperature is, among others, the most deteriorating factor of wear, thus being strongly wear-accelerating even under boundary lubrication.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.4
• /
• pp.337-343
• /
• 2004

This paper presents an experimental study of friction and wear properties of a unidirectional oriented continuous crbon-fiber reinforced epoxy composite at the ambient temperature. Friction and wear experiments were conducted in the three principal sliding direction of the fiber orientation in the composite were selected against the stainless steel counterpart specularly processed were using a pin -on-disc apparatus. Friction coefficient and specific wear rate at various normal loads and sliding velocities wear determined. When sliding took place against smooth and hard counterpart, the hightest were resistance and the lowest friction coefficient were observed in the anti-parallel direction. The wear track of the worn specimens was examined with a scanning electron microscope(SEM) to observe the damaged fibers on the surface. In addition, SEM observations of the worn surfaces allowed to identify the involved different wear mechanisms.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.11a
• /
• pp.88-88
• /
• 1998

• Tribology and Lubricants
• /
• v.29 no.6
• /
• pp.360-365
• /
• 2013

In this study, sliding wear tests were conducted to investigate the effects of tempered hardness on the sliding wear behavior of bearing steel. At a sliding speed of 0.3 m/s, the wear resistance of bearing steel with a tempered hardness of HRC 54 was superior to that with HRC 62. It was found that bearing steel with HRC 54 showed a strong tendency for the occurrence of oxidation wear at that speed, compared to that with HRC 62. This would be due to the troostitic structure of bearing steel with HRC 54, which is highly susceptible to corrosion. In this context, it is considered that sliding wear behavior could be affected by the corrosion resistance of the material.

• Tribology and Lubricants
• /
• v.36 no.3
• /
• pp.117-123
• /
• 2020

In this study, the effect of the pre-mild wear mode test condition on the subsequent severe wear behavior of carbon steel has been investigated when the wear mode is varied according to the sliding speed change during sliding contact. Two sliding speeds of 0.3 m/s and 3 m/s for the mild wear mode test have been chosen and a sliding speed of 1 m/s for the severe wear mode test. A mild wear mode test at two different sliding speeds has been carried out during the severe wear mode test and total sliding distance of the mild wear mode test has been changed at this time. As a result, it could be found that the wear rate of carbon steel under the severe wear mode test after performing a pre-mild wear mode test is significantly reduced, compared with that before performing. However, its wear rate was slightly higher than that under the mild wear mode test. Oxides produced during the pre-mild wear mode test have been found to play a significant role in reducing the wear rate under the subsequent severe wear mode test. In particular, it was found that the effect of a pre-mild wear mode test performed at the sliding speed of 3 m/s has more rapid and the reduction in the wear rate was greater than thst at the sliding speed of 0.3 m/s.

• Tribology and Lubricants
• /
• v.27 no.6
• /
• pp.351-355
• /
• 2011

Al/SiC composites were fabricated by thermal spray process, and the dry sliding wear tests were performed using the various sliding speed of 10, 30, 60 and 90 RPM through 1000 cycles. The applied load was 10 N and radius of wear track was 15 mm. Wear tracks on the Al/SiC composites were investigated using scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS). In the case of sliding speed of 10 RPM, adhesive wear behavior caused by plastic deformation of composits surface was observed. In the cases of sliding speed of 30, 60, 90 RPM, abrasive wear behavior on the adhered layer formed by debris were observed. Through this study, it was found that the wear behavior of Al/SiC composites was mainly influenced by the sliding speed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06b
• /
• pp.29-34
• /
• 1989

고분자 복합재료들은 오늘날 광범위하게 마찰 부위들에 응용되고 있다. 다양한 첨가제와 보강재들이 고분자 물질들에 넣어져 강도와 마모 특성들을 향상 시키고 있다. 예를 들어, 다양한 복합재료들로서 현재 입수 가능한 것에 베어링 재료들이 있으며 이에 포함되는 것이 자체 윤활 보강 플라스틱 들이며 이들에는 고체 윤활제, 즉, 테플톤, $MoS_2$, 혹은 흑연가루들이 첨가된다. 실험적 그리고 이론적인 연구들이 여러 조건들에서의 섬유 보강 복합 재료들의 마모 거동에 대하여 보고되었다(예를 들어, 미끄럼 마모, 연마 마모, 입자 충격 마모, 비빔 마모). Tsukizoe와 Ohmae의 보고에 의하면 탄성계수 탄소섬유 복합재료는 가장 적은 마모가 횡단 방향(Transverse)에서 있고, 고 강도 탄소 섬유 복합재료는 길이 방향(Longitudinal)에서 있다. 가장 많은 마모는, 고 탄성계수 복합재료는 길이 방향에서, 고 강도 섬유 복합재료는 횡단 방향에서 잇다. 그들이 또한 발표한 것은 양쪽의 고 탄성계수와 고 강도 섬유 복합재료들의 수직방향(Norma)에서 눌러 불음(Seizure)가 일어났다고 한다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.04a
• /
• pp.59-62
• /
• 1993

고품위의 동력전달 장치와 같은 고정밀 기능 부품들은 보다 높은 비강도, 고경도, 내마모성 및 내식성을 가져야 하며, 특히 소재의 마찰, 마모 특성은 기아제품 등의 수명, 정밀도 및 에너지 손실을 좌우하는 것으로서 물성의 열화를 극복할 수 있는 소재의 개발이 요구되고 있다. 지난 수년동안 금속기지에 $Al_2O_3$나 SiC등의 보강재를 첨가하여 복합재의 응착 및 연삭마모에 대한 저항성을 향상시키는 시도를 하고 있다. 주로 제조비용이 낮고 거의 등방적인 성질을 가지며 가공성이 좋은 입자 보강 복합재료에 대한 연구가 지배적이었지만, 입자 보강 복합재료의 경우 강도 및 탄성계수의 향상 정도가 적다는 단점을 지니고 있다. 본 연구에서는 분말야금법을 이용하여 금속기지에 세라믹상으로 SiC 입자 및 휘스커가 첨가된 복합재를 제조하여 제조공정변수에 따라 마모거동을 pin-on-disk 형태의 마모시험기에서 실험하였으며, 주사전자현미경으로 마모표면관찰 등으로 복합재의 마모기구를 연구하였다.

• Tribology and Lubricants
• /
• v.29 no.2
• /
• pp.85-90
• /
• 2013

The effects of contact pressure on the sliding wear behavior of mild steel in a pin-on-disc type apparatus were investigated. Sliding wear tests were conducted with various combinations of the load and apparent area of contact. The wear behavior of mild steel as a function of sliding speed was independent of contact pressure. However, the wear rate at different sliding speeds was influenced by the load regardless of the apparent area of contact. This was attributed to the fact that there may be no difference in the real area of contact for any combination of the load and apparent area of contact.

• Tribology and Lubricants
• /
• v.30 no.6
• /
• pp.364-369
• /
• 2014

To assess the wear behavior of rails against subway rail car wheels, we investigate the sliding wear behavior of pins derived from two types of rails (normal rails and heat-treated rails) against a disc derived from a subway rail car wheel, using a pin-on-disc-type tribometer. We base the sliding wear test conditions on the sliding conditions for wheel flange-rail gauge corner contact. We demonstrate the remarkable transition in the wear behavior of the pins derived from the rails, from severe wear to mild wear, as a function of the sliding distance. The wear rate of the heat-treated rail material in the running-in wear region is much lower than that of the normal rail material. Furthermore, the wear rates of the pins in the running-in wear region decrease with increasing hardness and with decreasing sliding speed. However, there is little difference between the heat-treated rail pin and the normal rail pin in the wear rate in the steady-state wear region. Stricter controls on the decarburized layer beneath the surface of rails are required to reduce the wear rate in the running-in wear region.