본 연구는 배수성 아스팔트 포장의 표면을 아크릴 수지로 코팅 처리할 경우 내구성 측면 및 기능적 측면에서 어떠한 효과가 있는가를 실내시험을 통해 평가하는 기초적인 연구이다. 포장의 내구성 측면에서는 칸타브로 및 휠트래킹, 수분손상 간접 인장 피로 시험 등을 실시하였다. 시험결과 시편을 수지로 코팅을 한 경우 칸타브로 손실률이 3배 정도 감소되었고 균열에 대한 저항성도 대폭 향상되었으나 수분손상 및 소성변형의 저항성은 큰 차이가 없는 것으로 나타났다. 기능적인 측면에서는 코팅 전 후의 투수계수 및 공극률 BPT(British Pendulum Tester)를 사용한 미끄럼 저항성의 변화를 측정하였다. 시험결과 공극률 및 투수계수는 약간 저하되나 기능상의 문제는 없을 것으로 판단되며, 미끄럼 저항성은 규사를 살포하지 않을 경우 미끄럼 저항성이 감소되나 규사를 살포할 경우 코팅 전 수준 이상의 미끄럼 저항성을 확보하는 것으로 나타났다.
재래의 표준기어방식으로는 여러 가지의 취약점이 있는데, 이러한 결점은 치형을 다시 교 정(correction)하는 전위기어방식으로 설계하여 성능이 개선되고 해결될 수 있다. Corrected tooth의 창성은 공구를 전위하여 절삭하므로 이루어지고, 이 방식은 치형곡선의 곡률반지름을 증가시키며, 미끄럼률을 감소시켜서 강도를 증가시키도록 설계할 수 있다. 본 해설에서는 전위 기어 영역에서 기어의 성능개선과 복잡한 강도의 설계방법등을 최근경향에 부합시키고 통일된 형식의 체계로 기어설계를 쉽게 발전시킬 수 있도록 시도한 것이다.
Several methods have been developed to predict the creep rupture time of the steam pipes in thermal power plant. However, existing creep life prediction methods give very conservative value at operating stress of power plant and creep rupture strain cannot be well estimated. Therefore, in this study, creep rupture time and strain prediction method accounting for material damage and grain boundary sliding is newly proposed and compared with the existing experimental data. The creep damage evolves by continuous cavity nucleation and constrained cavity growth. The results showed good correlation between the theoretically predicted creep rupture time and the experimental data. And creep rupture strain may be well estimated by using the proposed method.
본 논문에서는 기존의 TE(transverse excitation) 방식과 달리 LE(longitudinal excitation) 방식을 사용하여 유전체 표면을 따라 발생하는 미끄럼 방전에 의해서도 질소레이저 발진이 가능함을 보였다. 이는 방전여기 방식인 엑시머 레이저 등의 기체 레이저에서도 미끄럼 방전을 이용한 레이저 발진이 가능함을 의미한다. 또한, 레이저빔의 형상이 공진기의 원둘레를 따라 발진이 되어 빔이 환 모양으로 출력이 됨을 보임에 따라 직사각형이나 타원형의 빔 등 폐곡선을 이루는 어떤 특정한 형태의 질소레이저 빔도 만들어 낼 수 있다는 가능성을 보였다. 레이저의 동작특성인 출력과 안정성은 TE 방식에 비해서도 뒤떨어지지 않는 다는 것을 알 수 있었으며, 공진기의 지름이 2배 증가하면 미끄럼 방전이 일어나는 표면이 2배, 체적은 4배 증가하여 그에 따른 방전간극과 유동률이 비례관계에 있음을 알 수 있었다.
The operating torque and tribological characteristics of the cam/tappet system in an I.C. engine have an important effect on engine efficiency. In this paper, we measured the torque of cam/tappet system with respect to the oil temperature and camshaft speed to characterize the tribological behavior. Also, accelerated test was performed to analyze the wear characteristics of cam/tappet interface. The torque of the cam/tappet system decreased with respect to camshaft speed and was not significantly affected by the oil temperature. The results of accelerated test showed that the running-in wear occurred during the tests and the center of the tappet was mainly damaged by the rolling and sliding friction.
This paper presents an anti-lock braking system for commercial vehicles with pneumatic brake system by using slip ratio. By virtue of system reliability, most commercial vehicles adopt pneumatic brake system. However, pneumatic brake systems control is more difficult than hydraulic systems due to a longer time delay and the system nonlinearity. One of the major factors in generating braking forces is the wheel slip ratio. Accordingly, the proposed ABS strategy employs the slip ratio threshold-based valve on/off control. This threshold-based algorithm is simple but effective to control the pneumatic brake systems. The control performance of the proposed algorithm has been validated via simulation studies using MATLAB/Simulink and Trucksim. The results show ABS by using slip ratio reduces the braking distance and improves vehicle control.
본 논문은 엘리베이터의 미끄럼이나 과속을 방지할 수 있는 보조 제동장치인 로프 브레이크에 관한 것으로 제동시 반력의 최대 영역 즉, 취약 부분(weak point)으로 예상되어지는 하우징 영역의 보강형상을 위치와 높이를 변화시켜서 구조해석을 수행하여 최대응력과 최대변형률을 비교 분석하여 하우징의 안전성을 검토한 후, 최적형상의 하우징을 적용시킨 로프 브레이크의 설치 각도에 따른 구조해석을 수행하여 구조적 타당성을 검토하고자 한다.
In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear not only in the root, but the tip of tooth and tooth edge.
This paper presents a mathematical model which is about the dynamics of not only a two wheel steering vehicle but a four wheel steering vehicle. A sliding mode ABS control strategy and PID rear wheel control logic are developed to improve the brake and cornering performances, and enhance the stability during emergency maneuvers. The performances of the controllers are evaluated under the various driving road conditions and driving situations. The numerical study shows that the proposed full car model is sufficient to accurately predict the vehicle response. The proposed ABS controller reduces the stopping distance and increases the vehicle stability. The results also prove that the ABS controller can be employed to a four wheel steering vehicle and improves its performance. The four wheel steering vehicle with PID rear wheel controller shows increase of stability when a vehicle speed is high and sharp cornering maneuver when a vehicle speed is low compared to that of a two wheel steer vehicle.
본 연구에서는 치차의 소음은 근본적으로 치형에 관계된 것으로 생각하여 치 차소음을 감소시키기 위해 제시한 방법에 적합한 치형, 즉 물림률을 증가시킬 수 있고 동시에 치형수정의 효과를 나타내며, 미끄럼률.치면접촉응력.이뿌리응력이 작은 인벌 류트-사이클로이드 하벙치형을 유효치형으로 하여 저소음 치차의 치형을 치차의 소음 을 감소시키기에 적절한 치형설계조건을 설정하여 설계한다. 설계한 합성치형치차의 소음저감성능을 확인하기 위해 치형을 생성시키는 컴퓨터프로그램의 치형데이터를 이 용하여 합성치형치차, 인벌류트치차, 그리고 사이클로이드치차를 NC Wire Cutting Ma- chine으로 가공하고 각 치차에 대해 소음측정실험을 하여 소음레벨을 비교검토한다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.