• Magazine of the Korea Concrete Institute
• /
• v.1 no.1
• /
• pp.75-86
• /
• 1989

본 본문에서는 실리카 흄을 사용한 고강도 콘크리트의 제조와 역학적 특성 및 최적 배합에 대한 실험적 연구를 수행하였다. 본 본문에서는 주요 실험변수를 물-시멘트비와 혼화재인 실리카 흄의 혼입량으로 정하였으며, 압축강도 및 휨강도와 합렬인장강도 특성을 분석하였다. 실리카흄의 혼입으로 강도가 증가함을 발견하였으나 어느 범위이상의 과도한 혼입은 오히려 강도를 저해하는 것으로 나타났다. 물-시멘트비 0.28에서는 실리카 흄 혼입량이 5%일 때 최대의 강도가 나타났고, 물-시멘트비 0.40에서는 15%, 물-시멘트비 0.55에서는 20%혼입에서 가장 큰 강도가 나타났다. 또한 본 연구에서는 압축강도와 물-시멘트비 및 실리카 흄량 사이의 관계를 도출하여 그 관게식을 제시하였으며, 이 식으로부터 소요강도를 위한 본 배합변수를 유추할 수 있다. 본 연구결과 물-시멘트비 효과와 실리카 흄의 효과가 상쇄되는 구간이 존재하며, 따라서 이들 효과를 함께 고려한 최적배합을 도출하여 제시하고 있다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.325-326
• /
• 2009

The present study concerns the acid neutralization capacity (ANC) of cement paste, mortar and concrete depending on a free water-cement ratio. The ANC of paste at 30%, 40% and 50% of water-cement ratio was measured and simultaneously the effect of aggregate on the ANC was evaluated. It was found that an increase in the acid concentration resulted in a decrease in the pH of the suspension, in particular, at 10 in the pH, a sharp decrease was observed. The ANC showed some peak resistances to acid at particular pH values.

• Journal of the Korean Ceramic Society
• /
• v.38 no.8
• /
• pp.716-723
• /
• 2001

시멘트 모르터의 소성수축에 의한 균열을 방지하기 위해 소성수축 특성에 관한 연구를 수행하였다. 우리나라 봄철의 대표적인 기후인 온도 20$\pm$3$^{\circ}C$, 상대습도 55%, 풍속 3.5m/s의 기후조건으로 하였으며, 모르터의 물 시멘트 비, 시멘트 골재 비, 팽창재 사용, 플라이 애쉬 치환, 수분증발을 억제하기 위한 중점제 등을 사용하여 소성수축의 특성을 검토하였다. 연구 결과 소성수축 변형은 응결시간과 밀접한 관계가 있으며 응결시간이 빠를수록 변형은 크게 나타났다. 또한 물시멘트 비에 의해서도 소성수축 변형은 큰 것으로 나타났다. 모르터에서의 골재 비율이 작거나, 플라이 애쉬의 치환율이 클수록 소성수축 변형은 매우 크게 나타났다. 중점제의 사용은 소성수축 변형을 줄이는데 효과가 있었으며, 건조수축 보상용 팽창재의 사용은 소성수축 변형율을 크게 하는데 이는 ettringite 생성에 의한 물 시멘트 비의 감소효과를 가져오기 때문이다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.51-61
• /
• 2018

Foundation of tower structures such as wind turbine, pylon, and chimney have to resist considerably large overturning moment due to long distance from foundations to load point and large horizontal load. Pile foundations subjected to uplift force are needed to economically support such structure even in the case of rock layer. Therefore, this research performed the laboratory model tests with the variables, W/C ratio and sand proportion, to evaluate the effect of the mix proportion of grouting material on shaft resistance. In the case of cement paste, maximum and residual shaft resistance were distributed in uniform range irrespective of the changes of W/C ratio. However in the case of mortar, they were decreased with increasing W/C ratio, while they were increased and then decreased with increasing sand proportion. In the case of no sand, the maximum shaft resistance was about 540~560kPa regardless of the W/C ratio. When the sand proportion was 40%, it was about 770~870kPa depending on W/C ratio, which was about 40~50% higher than that without sand. The optimum proportion found in this research was around 40% of sand proportion and 80~100% of W/C ratio.

• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.667-675
• /
• 2006

Concrete is much more easily damaged by various parameters than by the only one and performance reducing mechanism grows more complicated in that condition. In addition, the factors which really act in concrete structure tend to be activated in turn and the degradation of concrete is very rapidly progressed. The purpose of this study is to evaluate the properties of polymer cement mortars under combined cures. The polymer cement mortars are prepared with various polymer types, polymer-cement ratios and cement-fine aggregate ratio, and tested for compressive and flexural strengths, accelerated carbonation, chloride ion penetration and acid resistance test, and freezing-thawing test. The properties of polymer cement mortars under combined cures is discussed. From the test results, polymer cement mortars have superior strengths compared with plain cement mortar under combined cures. The strengths of polymer cement mortars are markedly increased at curing condition II and V, however strengths are not improved at curing condition I and IV irregardless of polymer types. The carbonation and chloride ion penetration depths of polymer cement mortars tend to decrease in curing conditions, III-C, IV-B, V-A order, and decrease with increasing polymer cement ratios. It is concluded that polymer cement ratio of 10 to 15% are considered optimum for the preparation of such polymer cement mortars.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1997.05a
• /
• pp.19-24
• /
• 1997

콘크리트 구조물이 고온에 가열되면 그 성질이 변화하여 구조물은 다양한 영향을 받는다. 콘크리트 구조물의 고온에서의 성상은 시멘트의 종류, 골재의 성질, 배합비, 함수율, 재령 등에 의해 다르다. 콘크리트의 열성질에 관한 외국에서의 연구는 다수 보고되었으나 국내에서 연구한 결과는 없으며 특히 시멘트의 종류, 골재의 성질 등에 따라 고온에서의 성상이 다르기 때문에 본 연구에서는 국내에서 생산되는 시멘트, 골재를 대상으로 하였다. 또한 콘크리트 배합을 일반 구조물 및 아파트 현장에서 사용하는 배합비로 시험체를 제작ㆍ실험하였다. (중략)

• Magazine of the Korea Concrete Institute
• /
• v.10 no.5
• /
• pp.177-187
• /
• 1998

최근 국내에서 해양 구조물, 장대 교량의 하부구조물, LNG저장탱크 등 매스콘크리트의 증가추세에 따라 구조물의 고내구성과 관련하여 시멘트의수화열에 의한 온도균열의 발생을 최소화 시킬 수 있는 3성분계 혼합형 저발열시멘트가 개발되어 실 구조물의 적용단계에 있으나, 저발열시멘트가 개발되어 실 구조물의 적용단계에 있으나 저발열시멘트의 특성에 대한 전반적인 연구보고가 국내에서는 미진한 실정이다. 따라서 본 연구에서는 3성분계 혼합형 저발열시멘트의 특성 및 코\ulcorner리트의기초물성을 1종 보통포틀랜트 시멘트, 5종 내황산염시멘트, 슬래그시멘트와 비교하였다. 글 결과 저발열 콘크리트의 찹축강도는 초기재령에서 강도발현률이 적은 반면 장기강도발현률은 상당히 큰 경향을 보였다. 또한 수화열은 1종시멘트를 사용한 콘크리트에 비하여 1/3~1/2정도로 매스콘크리트의 수화열을 대폭적으로 저감시킬 수 있을 뿐만 아니라 염소이온에 대한 저항성이 상대적으로 높게 나타나 거대 해양 구조물의 적용에 매우 유리한 시멘트로 판단되었다.

• Journal of the Korea Concrete Institute
• /
• v.26 no.5
• /
• pp.591-598
• /
• 2014

In this study, the relationship between compressive strength and water-cement ratio according to water reducing ratio was evaluated, concrete mix was prepared according to 3 level of water reducing ratio (0%, 8% and 16%) and 3 level of water-cement ratio (40%, 45% and 50%). In addition, concrete mix was carried out repetition test of three times in order to secure the reliability. As a result, compressive strength according to water reducing ratio was shown that difference of strength was about 20% occurred, effect of compressive strength according to water reducing ratio was found more than the water-cement ratio. Therefore, reflected the effect of water reducing ratio, relationship equation between new compressive strength and water-cement ratio was proposed.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.148-155
• /
• 2013

The purpose of this study is to clarify the effect of the emulsifier ratio on the properties of the polymer cement mortars based on styrene-butyl acrylate (S/BA) latexes, and to obtain necessary basic data to develop appropriate latexes for cement modifiers. The polymer dispersions for cement modifiers was synthesized using styrene and butyl acrylate. Polymer cement mortars based on S/BA latexes were prepared with various monomer and emulsifier ratios, and their water-cement ratio, air content, flexural and compressive strengths, water absorption and chloride ion penetration were tested. From the test results, the maximum flexural and compressive strengths of polymer cement mortars based on S/BA latexes were obtained at a bound styrene content of 60% and an emulsifier ratio of 6%. Also, the water absorption and chloride ion penetration depth are greatly affected by the polymer-cement ratio rather than the bound styrene and emulsifier content. Accordingly, it is judged that S/BA latexes can be used place of the conventional polymer dispersions of cement modifier.

• The Journal of Engineering Geology
• /
• v.26 no.1
• /
• pp.101-115
• /
• 2016

We carried out laboratory material tests on two cements (KS-1 ordinary Portland and Class G) with changing W/S (Water/Solid) and the content of fly ash in order to evaluate their physical and mechanical properties. The specimens of KS-1 ordinary Portland cement were prepared with varying W/S (Solid=cement) in weight, while those of Class G cement were prepared with changing the content of fly ash in volume but maintaining W/S (Solid=cement+fly ash). The results of the material tests show that as the W/S in KS-1 ordinary Portland cement and the content of fly ash in Class G cement increase, the properties (density, sonic wave velocity, elastic constants, compressive and tensile strengths, thermal conductivity) decrease, but porosity and specific heat increase. In addition, an increase in confining pressure and in the content of fly ash leads to plastic failure behavior of the cements. The laboratory data were then used in a stability analysis of cement sheath for which an analytical solution for computing the stress distribution induced around a cased, cemented well was employed. The analysis was carried out with varying the injection well parameters such as thickness of casing and cement, injection pressure, dip and dip direction of injection well, and depth of injection well. The analysis results show that cement sheath is stable in the cases of relatively lower injection pressures and inclined and horizontal wells. However, in the other cases, it is damaged by mainly tensile failure.