• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.358-363
• /
• 2009

Maleic anhydride-grafted polypropylene has been widely used to improve the interfacial interaction between the components in PP/polar polymer blends and PP/filler composites and to maximize the physical properties and thermal properties. In this paper. the maleic anhydride (MAH)-grafted polypropylene (co-PP) was fabricated through reactive extrusion process with di-cumyl peroxide (DCP) as an initiator. The grafting degree of MAH depending on the contents of DCP and MAH was investigated by FT-IR spectra and chemical titration. The grafting degree increased with increasing MAH concentration and also showed maximum value at 0.06 wt% of DCP concentration. Melt flow index (MFI) of the grafted copolymer was increased with increasing the contents of MAH. The DSC and TGA analysis data indicate the melting temperature and thermal degradation of PP depending on the grafting degree of MAH.

• Resources Recycling
• /
• v.18 no.2
• /
• pp.69-76
• /
• 2009

Alumina powder was prepared from heat-treatment of artificial marble waste fine aggregate containing $Al(OH)_3$ for the purpose of the feasibility of its recycling. Artificial marble waste was heat-treated between $500^{\circ}C$ and $1000^{\circ}C$ and XRD, BET surface area, BJH pore size distribution and adsorption of As were analyzed for heat-treated powder. It was found that the adsorption efficiency of As was significantly affected by phase composition of alumina powder rather than its physical characteristic. Heat-treated powder compact was sintered to produce the pellet. Alumina pellet with porosity more than 60% could be obtained after sintering below $1200^{\circ}C$ and also the addition of glass powder as a sintering aid had a positive effect on lowering sintering temperature, led to the high porosity near 60% and adsorption of As over 60% even at $900^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3345-3350
• /
• 2014

We investigated to assess the relationships between the major nutrients and phytoplankton dynamics during the spring season in 2010 and 2011 at 23 stations in Jinhae Bay, Korea. The bay is divided into four different zones based on pollutant sources and geographical characteristics. Nutrient limitation (>80%) was significant in Zone II, which is located in central bay and is influenced by the water well mixed from outer bay. The limited nutrient was followed in Zone III and IV that was occupying between 17% and 83%. However, the low levels are being kept below 35% in Zone I, which is characterized by the semi-enclosed eutrophic area of Masan and Haegam bays. Based on the PCA (principle component analysis) analysis, the nitrogen (N) sources in 2010 were particularly dominant and it may be due to the water mixing and wastewater formed from bottom layers and sewage. In 2011, major nutrients including nitrogen, silicon and phosphorus were dominant in the bay and are supplied by the river discharge after rainfalls with low salinity conditions. In particular, the N nutrients being supplied in 2010 are correlated with pennate diatoms Pseudo-nitzchia spp. and is not related to the phytoplankton population densities in 2011. The present study suggests that N sources play an important role in the proliferation of diatom, and the rapid nutrient uptakes by them are potential nutrient limitation factors in the bay.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.3-3
• /
• 2003

고밀도 플라즈마를 생산할 수 있는 대면적용 플라즈마 소스의 개발은 미세전자구조 산업에서부터 FPD 산업에 이르기까지 많은 영역에 걸쳐 필수 불가결한 기술요소가 되어가고 있 다. 이러한 대면적용 고밀도 플라즈마에의 적용을 위하여 새로운 유도결합형 플라즈마 소오스의 개발이 진행되고 있으며, 차세대 반도체 식각 및 세정 공정을 위하여 여러 형태의 안 테나가 연구되어지고 있다. 그러나 TFT -LCD에 적용이 가능하게끔 기존의 ICP 소오스를 직 접적으로 대면적화 하는 데에는 여러 가지 문제점들로 인해 그 한계점이 들어났다. 그 예로 안테나의 길이가 길어짐에 따른 안테나 저항 값이 커지며, 안테나 소스 길이자체가 사용하는 인가전력(13.56MHz)의 반파장에 해당되는 길이가 되었을 경우 생기는 심각한 정상파 효과, 유전물질의 두께 증가 및 그에 따른 재료비의 상승 및 관리상의 어려움들이 바로 그것 이라 할 수 있겠다. 그러므로, 본 연구에서는 차세대 TFT -LCD 대면적 공정에 적용 가능한 고밀도 플라즈마 를 발생시키기 위해서 내장형 유도결합형 선혈 안테나를 사용하였다. 내장형 유도결합형 선 혈 안테나가 가지고 있는 고유의 정전기적 결합효과를 최소화시키기 위해 직사각형모앙의 플라즈마 댐버(830mm*1,020mm)에서 영구자석을 사용하여 multi-cusp 자장효과 및 다양 한 자장의 배열에 따른 플라즈마 특성변화를 살펴보았다. 영구자석을 사용하여 외부자장을 인가하였을 때가, 그럴지 않은 때보다 RF 안테나 코일의 전압을 낮춰주었으며, 영구자석의 배열에 따라 코일의 인덕턴스의 값이 크게 변함을 알 수 있었다. 그리고 최적화된 자장의 배열은 플라즈마의 이온밀도를 증가시켰으며, 플라즈마의 균일도도 10% 이내로 유지됨을 알 수 있었다. 또한 영구자석에 의한 자장의 유무 및 공정압력과 인가전력에 따른 P Photoresist Film의 식각특성에 관해 살펴보았다.증을 위한 실험.측정장비의 구입 및 업계와의 공동활용, 국내.외 최신기술 정보자료의 수집과 신속제공, 국내.외 전문가 초청 활 용, 미래 지향적 목적활용 기초연구사업 수행, 미래기술 동향예측 및 홍보 등을 통해 서 국내 도금기술의 기술자립 및 고도화를 위한 여건마련을 위하여 노력하고 있다.빛 이때의 부식속도(선형분극법), 인위적인 피막 파괴 전,후 의 전위 변화 및 부식속도 측정법에 의한 국부부식 발달 저지능 등을 평가하여 각 실험결과를 비교분석하여 보았다. 수록 민감하여 304 의 IGSCC 와 매우 유사한 거동을 보인다. 본 강연에서는 304 와 600 의 고온 물에서 일어나는 IGSCC 민감도에 미치는 환경, 예민화처리, 합금원소의 영향을 고찰하고 이에 대한 최근의 연구 동향과 방식 방법을 다룬다.다.의 목적과 지식)보다 미학적 경험에 주는 영향이 큰 것으로 나타났으며, 모든 사람들에게 비슷한 미학적 경험을 발생시키는 것 이 밝혀졌다. 다시 말하면 모든 사람들은 그들의 문화적인 국적과 사회적 인 직업의 차이, 목적의 차이, 또한 환경의 의미의 차이에 상관없이 아름다 운 경관(High-beauty landscape)을 주거지나 나들이 장소로서 선호했으며, 아름답다고 평가했다. 반면에, 사람들이 갖고 있는 문화의 차이, 직업의 차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$순응$\lrcorner$과 $\ulcorner$표현$\lrcorner$

• Korean Journal of Heritage: History & Science
• /
• v.45 no.3
• /
• pp.194-211
• /
• 2012

Pung-nap mudcastle has brought wide attention to archaeologists since scientific studies were carried out on the various types of building sites and excavated potteries related to A period of Baekje Kindom when it sat Hansung as the capital. It is identified that clay from Ra-No.19 site of Pung-Nap mudcastle has different from compositions that of residential soil. From archaeological point of view, it is believed that the the soil was a source material for potteries due to the appropriate viscosity and inclusions. Mineralogical and geochemical studies show that the compositions between the source material and randomly chosen two potteries from the same site are similar. Behavior pattern classification of major, trace and rare elements provides also very similar result. Artificial specimen has been made at different temperature in order to estimate firing temperature of the potteries by means of various kinds of instrumental application. As a result of the study, it is believed that the firing temperature of the red and brown pottery was $550{\sim}600^{\circ}C$ and $900{\sim}1,000^{\circ}C$ respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.91-96
• /
• 2020

The 33-mode dielectric and piezoelectric properties of Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 piezoelectric single crystals were measured under large electric field and compressive stress. The phase transition from the low temperature rhombohedral to the high temperature tetragonal structure was observed in the range of 110~140℃, and the Curie temperature changing to the cubic structure was about 165℃. The polarization change according to the compressive stress and electric field was measured. Relative dielectric constant was calculated from the slope of the polarization curve applied to the electric field, and the calculated relative dielectric constant increased as the applied stress increased, and the relative dielectric constant decreased as the applied electric field increased. The strain according to the compressive stress and electric field change was measured, the piezoelectric constant was calculated from the slope of the curve, and the phase transition according to the application of pressure was confirmed. In the case of practical application as an underwater or medical ultrasonic actuator, it is necessary to properly design the magnitude of the compressive stress applied to the device and the DC bias in order to maintain linear driving.

• Applied Chemistry for Engineering
• /
• v.34 no.1
• /
• pp.15-22
• /
• 2023

Recent studies have actively investigated ways to improve the economic feasibility and efficiency of the Fischer-Tropsch process by increasing the yields of the monocyclic aromatic compounds (BTEX). In this study, ethylene was selected as a model of F-T-derived hydrocarbons, and the ethylene-to-aromatics (ETA) reaction was investigated according to changes in acid characteristics, mesopores, and crystallinity of HZSM-5 (HZ5). Fluorinated HZ5 was prepared by calcination followed by impregnation of an aqueous NH₄F solution having different molar concentrations in HZ5, and the structural and chemical properties of F/HZ5 were investigated through Brunauer-Emmett-Teller (BET), solid-state nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), NH₃-temperature-programmed desorption (TPD), and pyridine-IR spectroscopy. The ETA reactions were performed at 673 K under 0.1 MPa, and fluorinating HZ5 by an aqueous NH₄F solution of 0.17 M improved ethylene conversion, BTEX selectivity, and catalytic stability due to acidity, mesopore fraction, and crystallinity.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.159-169
• /
• 2007

The behavior of fiber-reinforced cemented sands (FRCS) was studied to improve a brittle failure mode observed in cemented sands. Nak-dong River sand was mixed with ordinary Portland cement and a Polyvinyl alcohol (PVA) fiber. A PVA fiber is widely used in concrete and cement reinforcement. It has a good adhesive property to cement and a specific gravity of 1.3. A PVA fiber has a diameter of 0.1 mm that is thicker than general PVA fiber for reinforced cement. Clean Nak-dong River sand, cement and fiber at optimum water content were compacted in 5 layers giving 55 blows per layer. They were cured for 7 days. Cemented sands with a cement/sand ratio of 4% were fiber-reinforced at different locations and tested for unconfined compression tests. The effect of fiber reinforcement form and distribution on strength was investigated. A specimen with evenly distributed fiber showed two times more strength than not-evenly reinforced specimen. The strength of fiber-reinforced cemented sands increases as fiber reinforcement ratio increases. A fully reinforced specimen was 1.5 times stronger than a specimen reinforced at only middle part. FRCS behavior was controlled not only by a dosage of fiber but also by fiber distribution methods or fiber types.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.255-260
• /
• 2023

As demanding the detection of explosive molecules, it is required to develop rapidly and precisely responsive sensors with ultra-high sensitivity. Since two-dimensional semiconductors have an atomically thin body nature where mobile carriers accumulate, the abrupt modulation carrier in the thin body channel can be expected. To investigate the effectiveness of WSe₂ semiconductor materials as a detection material for TNT (Trinitrotoluene) explosives, WSe₂ was synthesized using thermal chemical vapor deposition, and afterward, WSe₂ FETs (Field Effect Transistors) were fabricated using standard photo-lithograph processes. Raman Spectrum and FT-IR (Fourier-transform infrared) spectroscopy reveal that the adsorption of TNT molecules induces the structural transition of WSe₂ crystalline. The electrical properties before and after adsorption of TNT molecules on the WSe₂ surface were compared; as -50 V was applied as the back gate bias, 0.02 μA was recorded in the bare state, and the drain current increased to 0.41 μA with a dropping 0.6% (w/v) TNT while maintaining the p-type behavior. Afterward, the electrical characteristics were additionally evaluated by comparing the carrier mobility, hysteresis, and on/off ratio. Consequently, the present report provides the milestone for developing ultra-sensitive sensors with rapid response and high precision.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.125-131
• /
• 2024

In this study, synthesized Ni/Ce_xZr_1-xO₂ catalysts were coated on the surface of honeycomb metalic monoliths to investigate catalytic activity in steam reforming of methane reactions. Supports with varying Ce/Zr ratios were synthesized to observe their behavior in the reforming reaction, and catalysts with Ni contents ranging from 5 wt% to 20 wt% were prepared to analyze the effect of Ni loading contents on catalytic activity. The catalysts were characterized by XRD, BET, TPR, and SEM. The TPR analysis indicated the formation of Ni-Ce-Zr oxide with a strong interaction between the active metal Ni and CeO₂-ZrO₂ support. The 15 wt% Ni/Ce_0.80Zr_0.20O₂ catalyst exhibited the highest activity and stability in the steam reforming of methane reaction. Catalysts with enhanced activity and stability were synthesized by manufacturing composite materials using excellent oxygen storage and donor properties of CeO₂ and the thermal properties of ZrO₂.