• Journal of the Korean GEO-environmental Society
• /
• v.12 no.1
• /
• pp.51-60
• /
• 2011

Electrical resistivity is applied for understanding details about layers and obtaining basic properties of soils to various measurement devices. The objective of this study is development of TRP(Temperature-compensated Resistivity Probe), analysis about effects of temperature changes during cone penetration test, and observation of characteristics of cone penetration. In order to observation of temperature changes according to a diameter difference of resistivity cone probe, the cone which has wedge type cone tip is made to two types, 2mm and 5mm. Temperature sensor is attached at 15mm below from cone tip because of an electrical interference with elecrical resistance probe. Delectrical connector is used to prevent electric disturbance between motor type penetrating machine and electrical resistivity cone probe. Application tests are carried out in acrylic cell whose diameter is 30cm with uniform Jumunjin sand according to densification caused by blows. The test results indicate that the temperature is increased uniformly during penetration and a tendency, characteristics of cone penetration, is discovered during altering state of soils. This study suggests that the temperature effects and characteristics of penetration should be considered in penetrating tests in order to conduct an accurate ground investigation using TRP(Temperature-compensated Resistivity Probe).

• Korean Journal of Food Science and Technology
• /
• v.36 no.2
• /
• pp.217-225
• /
• 2004

This study was carried out to reduce the loss of frozen dough quality during frozen storage. Using response surface method, ascorbic acid 160.4 ppm, L-cysteine 63.1 ppm, and SSL 0.6% were found to be optimum, with xanthan gum 0.3% (formula A) and Ultra tex-3 5% (formula B) added as cryoprotectants. During frozen storage at $-20^{\circ}C$, control rapidly deteriorated after 4 weeks, while formulas A and B showed slight deterioration with immutable quality after 10 weeks.

• The Journal of Engineering Geology
• /
• v.7 no.3
• /
• pp.191-205
• /
• 1997

Measurements on subsurface movement of the Songsanri tomb site including the Muryong royal tomb was conducted using a tiltmeter system for the period of 15 months form July 7, 1996 to September 30, 1997. Two coordinate tilt monitoring data shows the biggest movement rate of 2.3mm/m/yr toward south in the frontal wall(N-S tilt) of the Muryong royal tomb. Southward tilting of bricks above the southern fire place in the western wall of the Muryong royal tomb is a proof of southward tilting of the royal tomb since its excavation in 1971. The eastern wall of the Muryong royal tomb is also tilting toward inside the tomb with the rate of 1.523mm/m/yr. Furthermore, tilting rate of wall increases twice in rainy season. It is interpreted tbat infiltration of water into the tomb and nearby ground in rainy season results in dangerous status for the safety of tomb structure. On the whole, normal component tilting of the walls of the 5th tomb is large than its shear component. It shows a small displacement toward one direction without no abrupt change in its direction and amount of tilting. The tilting rate of walls of the 6th tomb is about 8.8mm/m/yr in the dry season which is much bigger than those of other tombs in rainy season. Deformation events of walls of the tombs are closely related to amount of precipitation and variation of temperature. In comparison with different weather conditions, tilting is much bigger during the period of rainy weather than sunny weather. It is interpreted that rainwater flew into the turm through faults and nearby ground. High water content in nearby ground resulted strength of ground. The tilting event of walls shows a hysterisis phenomenon in analysis of temperature effect on tilting event. The walls tilt rapidly with steep rising of temperature, but the tilted walls do not come back to original position with temperature falling. Therefore, a factor of steep increase of the temperature must be removed. It means the tomb have to be kept with constant temperature. The observation of groundwater level using three boreholes located in construction site and original ground represented that groundwater level in construction site is higher than that of original ground during the rainy season from the end of June to August. It means that the drainage system of the Muryong royal tomb is worse than original ground, and it is interpreted that the poor drainage system is related to safety of tomb structure. As above mentioned, it is interpreted that artificial changes of the tomb environment since the excavation, infiltration of rainwater and groundwater into the tomb site and poor drainage system had resulted in dangerous situation for the tomb structure. According to the result of the long period observation for the tomb site, it is interpreted that protection of the tomb site from high water content should be carried out at first, and the rise of temperature by means of the dehumidifier inside the tomb must be removed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.132-132
• /
• 2016

기계 가공품의 정밀화, 경량화 요구로 난색재로 분류되는 비철분야 및 복합재 가공용 공구개발에 대한 수요가 급증하고 있으나, 기존 난삭재 가공 시 절삭공구의 마모가 빠르고, 상대재의 융착 불량 등이 공구 수명 감소의 주요 영향으로 보고된다. 상기문제를 해결하기 위해 절삭가공 공정 중 과다한 절삭유의 사용에 따른 가공비용, 에너지소모 증가, 환경오염 등으로 절삭유의 최소화 또는 절삭유를 사용하지 않는 표면처리기술등의 친환경 가공기술의 개발이 필요하다. 내융착 및 내마모 특성 향상을 위한 표면코팅 방법으로 수소가 포함되지 않은 고경도 비정질 카본 (ta-C)이 있으나, ta-C 코팅 막은 경도 30 - 80 GPa, 잔류응력 3 - 10 GPa 범위로 일반 경질 코팅 막 (AlTiN, TiSiCrN : 평균 3 GPa)에 비해 높고 산업적 활용이 가능한 0.5 - 1.5 um 두께 수준의 후막화가 힘들어 매우 우수한 절삭공구용 코팅 막 특성에도 불구하고 적용사례가 매우 적다. 따라서, 본 연구에서는 아크플라즈마 방식 (Filtered Cathode Vacuum Arc Plasma, FCVA)을 활용한 고경도/무수소 카본 코팅 막을 후막형태로 증착하여 비철금속가공용 절삭 공구류의 수명향상 기법을 제시하고자 한다. ta-C 코팅 막의 기초 공정개발 단계에서는 바이어스 전압, 공정시간을 달리하여 ta-C 코팅 막의 기계적 물성(경도: $50{\pm}3GPa$, 잔류응력: $6{\pm}1GPa$, 밀착력: 30N 이상 및 트라이볼로지 특성: 마찰계수 0.1 이하, 마멸량: $1.85{\times}10-14mm^3$)을 확보하여 절삭공구로의 공정실용화 적용검토를 실시하였다. ta-C 코팅 막은 (1) WC 공구 및 기존 상용품인 (2) TiAlN/TiN/WC 구조에 대해 증착을 실시하였으며 코팅 막의 두께 변화에 따른 실제 절삭환경에서의 내수명 관측을 진행하였다. 시험결과, ta-C/WC의 단일막 구조인 절삭공구의 경우, 실제 절삭환경에서 쉽게 박리가 발생하여 코팅 막으로서의 효과를 나타내지 못하였다. 이는, 기초 공정개발 단계에서의 밀착력 기준이 실제 환경과 부합하지 않는 것을 의미하며 추후 공정개선을 통해 극복하고자 한다. 반면에, 상용품인 (2) TiAlN/TiN/WC 구조의 절삭공구 대비 ta-C/TiAlN/TiN/WC 구조에서 내수명 증가는 약 2.5배 (기존 300회, 코팅 후 800회)로 증가하였으며 ta-C 코팅 막의 두께가 $0.6-0.8{\mu}m$일 때 최대치를 취한 후 감소하였다. 이를 통해, 절삭공구로의 ta-C 코팅 막 효과는 최외각 층의 두께 범위와 모재 강도보강을 할 수 있는 적절한 중간층 막 (TiN/TiAlN 층)이 혼합되어 나타난 것으로 사료되며 현재 산업계로의 적용을 위한 대량생산용 코팅장비의 개발 및 비용절감을 위한 공정개발이 진행 중이다.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.145-154
• /
• 2005

Love wave and Rayleigh wave are the major elastic waves belonging to the category of the surface wave. Those waves are used to determine the ground stiffness profile using their dispersion characteristics. The fact that Love wave is not contaminated by P-wave makes Love wave superior to Rayleigh wave and other body waves. Therefore, the information that Love wave carries is more distinct and clearer than that of others. Based on theoretical research, the joint inversion analysis that uses the dispersion information of both Love and Rayleigh wave was proposed. This analysis consists of the forward modeling using transfer matrix, the sensitivity matrix for evaluating the ground system and DLSS (Damped Least Square Solution) as an inversion technique. The technique of joint inversion uses the dispersion characteristics of Love wave and Rayleigh wave simultaneously making the sensitivity matrix. The sensitivity matrix was used for inversion analysis repeatedly to find the approximate ground stiffness profile. The purpose of the joint inversion analysis is to improve accuracy and convergency of inversion results by utilizing that frequency contribution of each wave is different.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.3
• /
• pp.279-285
• /
• 2011

We perform a numerical study to determine the time of onset of natural convection in a transient hot wire (THW) device for measuring the thermal conductivity of nanofluids. The samples used in this simulation are water-based $Al_2O_3$ nanofluids with volume fractions of 1%, 4%, and 10%, and the properties are calculated by theoretical models and experimental correlations. The THW apparatus using coated wire is modeled by the control-volume-based finite difference method, and the start of natural convection is determined by observing the temperature rise of the wire under a gravity field. The onset time is 11.5 s for water and 41.6 s for water-based $Al_2O_3$ nanofluids predicted by Maxwell thermal conductivity model with a 10% volume fraction. We confirm that the onset time of natural convection of nanofluids in the cylinder increases with the nanoparticle volume fraction. We suggest a correlation for predicting the onset time on the basis of the numerical results. Finally, it is shown that the measurement error due to natural convection is negligible if the measurement using the transient hot wire method is completed before the onset of natural convection in the base fluid.

• Journal of Navigation and Port Research
• /
• v.28 no.6
• /
• pp.481-489
• /
• 2004

Ship collisions and grounding continue to occur regardless of continuous efforts to prevent such accidents. With the increasing demand for safety at sea and for protection of the environment, it is of crucial importance to be able to reduce the probability of accidents, assess their consequences and ultimately minimize or prevent potential damages to the ships and the marine environment. Numerical simulations for actual collision problem are conducted with a special attention with respect to finite element size, fracture criteria and material properties, which require a careful consideration to improve the accuracy. A parametric analysis varying colliding speed, angle, design loading condition is conducted using nonlinear finite element analysis method for 46,00 dwt Product/chemical carrier. The relationship between the absorbed energy and indentation are derived quantitatively using the insights observed from this study, and a novel design concept for assessing the anti-collision performance are proposed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.1
• /
• pp.143-149
• /
• 2016

This study evaluated the shear behavior of geogrid reinforced ballast material using a large scale direct shear test and discrete element method (DEM) based on PFC 3D program. The direct shear test was conducted on ballast materials that have different particle size distributions. Whereas the test results revealed that the shear strength generally increased with the larger particle size of ballast material without geogrid reinforcement, the shear behavior of ballast material was found to change pertaining to the relationship between particle size distribution and geogrid rib size. Generally, it is deemed the effectiveness of reinforcement can be achieved when the rib size is two times greater than average particle size. A numerical analysis based on DEM was conducted to verify the test results. The geogrid modeling was successfully completed by calibration process along with sensitivity analysis to have actual tensile strength provided by manufacturer. With a given geogrid model, the parametric evaluation was further carried out to examine the interactive behavior between geogrid and ballast material. Consequently, it was found that the effectiveness zone of geogrid reinforcement generated within a specific depth.

• The Journal of Engineering Geology
• /
• v.25 no.2
• /
• pp.237-250
• /
• 2015

Underground structures such as a tunnel have been considered as safer than structures on the ground during earthquake. However, severe damages of underground structures occurred at subway tunnel during 1995 Kobe Earthquake and such damages are gradually increased. In this study, a dynamic behavior of a cut and cover tunnel surrounded by weathered soils is investigated using Mohr-Coulomb Model. Parametric study was carried out for boundary conditions, tensile strength, and earthquake magnitudes. The results of numerical analyses in terms of ground deformations and stresses acting on the lining were quite dependent on the side boundary condition (free or fix conditions) and tensile strength of surrounding soils. The ground was deformed upward at the end of earthquake when the side boundary condition was fixed, whereas residual deformations were not predicted when it was free. When the tensile strength of a soil was set to the same as its cohesion, residual deformation was less than 1cm, regardless of side boundary conditions or input accelerations. In addition to that, stress conditions at the maximum deformation and end of earthquake were within an allowable range and considered as safe. Proper boundary conditions and material properties such as tensile strength are quite important because they may significantly impact on the results of dynamic analyses.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.532-542
• /
• 2018

Because maglev trains have a propulsion and absorption force without contact with the rails, they can drive safely at high-speed with little oscillation. Recently, test model of a maglev propulsion train was produced and operated, and has since been chosen as a national growth industry in South Korea; there have been many studies and considerable investment in these fields. This study examined the dynamic responses due to bridge-maglev train interaction and basic material to design bridges for maglev trains travelling at high-speed. Depending on the major factors affecting the dynamic effects, the scope of this study was restricted to the relationship between dynamic responses. A concrete box girder was chosen as a bridge model and injured train and rail types in domestic production were selected as the moving train load and guideway analysis model, respectively. From the analysis results, the natural frequency of a bridge for a maglev train, which has a deflection limit L/2000, was higher than those of bridges for general trains. The dynamic responses of the girder of the bridge for a maglev train showed a substantial increase in proportion to the velocities of the moving train like other general bridge cases. Maximum dynamic response of the girder is shown at a moving velocity of 240km/h and increased with increasing moving velocity of train. These results can be used to design a bridge for maglev propulsion trains and provide the basic data to confirm the validity and verification of the design code.