• Journal of the Korean institute of surface engineering
• /
• v.43 no.2
• /
• pp.105-110
• /
• 2010

Electroless nickel plating on porous carbon substrate for the application of MCFC electrodes was investigated. Acidic and alkaline bath were used for the electroless nickel plating. The pore sizes of carbon substrates were 16-20 ${\mu}m$ and over 20 ${\mu}m$. The carbon surface was changed from hydrophobic to hydrophilic after immersing the substrate in an ammonia solution for 40 min at $60^{\circ}C$. The contact angle of water was decreased from $85^{\circ}C$ to less than $20^{\circ}$ after ammonia pretreatment. The deposition rate in the alkaline bath was higher than that in the acidic bath. The deposition rate was increased with increasing pH in both acidic and alkaline bath. The content of phosphorous in nickel deposit was decreased with increasing pH in both acidic and alkaline bath. The contents of phosphorous is low in alkaline bath. The minimum concentration of $PdCl_2$ for the electroless nickel plating was 10 ppm in alkaline bath and 5 ppm in acidic bath. The thickness of nickel was not affected by the concentration of $PdCl_2$.

• Korean Journal of Metals and Materials
• /
• v.47 no.10
• /
• pp.675-680
• /
• 2009

Effects of $85^{\circ}C/85%$ Temperature/Humidity (T/H) treatment conditions on the peel strength of an electroless-plated Ni/polyimide system were investigated from a $180^{\circ}$ peel test. Peel strength between electroless-plated Ni and polyimide monotonically decreased from $37.4{\pm}5.6g/mm$ to $22.0{\pm}2.7g/mm$ for variation of T/H treatment time from 0 to 1000 hrs. The interfacial bonding mechanism between Ni and polyimide appears to be closely related to Ni-O bonding at the Ni/polyimide interface. The decrease in peel strength due to T/H treatment appears to be related to polyimide degradation due to moisture penetration through the interface and the bulk polyimide itself.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.4
• /
• pp.291-299
• /
• 2009

Ni-plated polytetrafluoroethylene(Ni-PTFE) particles($25{\mu}m$, $500{\mu}m$) were prepared by using nickel electroless plating. The Ni content in Ni-PTFE particles increased with increasing the amount of reduction agent. At about 53 wt% Ni content, $25{\mu}m$ Ni-PTFE particles showed conductivity of 320S/m. The Ni-PTFE particles were formed into the Ni-PTFE plate using heat treatment at $350^{\circ}C$ under $10{\sim}1000kg/cm^2$. The Ni-PTFE plate displayed the high conductivity of 5100S/m due to the formation of 3-dimentional Ni network. The plate was used as an electrode in an alkaline fuel cell(AFC). In terms of the current density, the Ni-PTFE electrode having higher Ni content(53 wt%) showed improved performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.155-161
• /
• 2013

In this study, a metal-plated polycarbonate was adopted as a material for bipolar plates in a polymer electrolyte membrane fuel cell (PEMFC). The coated layers included 40-${\mu}m$-thick copper, 10-${\mu}m$-thick nickel, and 0.3-${\mu}m$-thick gold that respectively played the roles of current conduction, adhesion between copper and gold, and minimization of surface corrosion. The maximum power of the air-breathing PEMFC with polycarbonate bipolar plates was $120mW/cm^2$, which was similar to that of graphite bipolar plates. Finally, the maximum power of a 12-cell stack of polycarbonate bipolar plates was $132.7mW/cm^2$, and it had an operating time of 12 h. Therefore, this was considered a suitable material for bipolar plates in PEMFCs.

• Composites Research
• /
• v.25 no.4
• /
• pp.93-97
• /
• 2012

Carbon nano fibers (CNFs) reinforced magnesium alloy (AZ91) matrix composites have been fabricated by liquid pressing process. In order to improve the dispersibility of CNFs and the wettability with magnesium alloy melt, CNFs were mixed with submicron sized SiC particles ($SiC_p$). Also, the mixture of CNFs and $SiC_p$ were coated with Ni by electroless plating. In liquid pressing process, AZ91 melts have been pressed hydrostatically and infiltrated into three reinforcement preforms of only CNFs, the mixture of CNFs and $SiC_p$ (CNF+$SiC_p$), and Ni coated CNFs and $SiC_p$ ((CNF+$SiC_p$)/Ni). Some CNFs agglomerates were observed in only CNFs reinforced composite. In cases of the composites reinforce with CNF+$SiC_p$ and (CNF+$SiC_p$)/Ni, CNFs were dispersed homogeneously in the matrix, which resulted in the improvement of mechanical properties. The compressive strengths of CNF+$SiC_p$ and (CNF+$SiC_p$)/Ni reinforced composites were 38% and 28% higher than that of only CNFs composite.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.250-253
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. The Ni contact was formed on the front grid pattern by electroless plating followed by anneal ing at $380{\sim}400^{\circ}C$ for $15{\sim}30$ min at $N_{2}$ gas to allow formation of a nickel-silicide in a tube furnace or a rapid thermal processing(RTP) chamber because nickel is transformed to NiSi at $380{\sim}400^{\circ}C$. The Ni plating solution is composed of a mixture of $NiCl_{2}$ as a main nickel source. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. The Ni/Cu contact was found to be well suited for high-efficiency solar cells and was successfully formed by using electroless plating and electroplating, which are more cost effective than vacuum evaporation. In this paper, we investigated low-cost Ni/Cu contact formation by electroless and electroplating for crystalline silicon solar cells.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.129-129
• /
• 2017

열전재료는 열에너지를 전기에너지로 또는 전기에너지를 열에너지로 직접 변환하는데 가장 널리 사용되는 재료이다. $Bi_2Te_3$계 열전 재료는 400K 이하의 비교적 저온 영역에서 높은 성능지수(Dimensionless Figure of merit, ZT($={\alpha}2{\sigma}T/{\kappa}$, ${\alpha}$: 제백계수, ${\sigma}$: 전기전도도, T: 절대온도, ${\kappa}$: 열전도도))를 나타내는 열전재료이며 자동차 시트나 정수기 등에 응용되고 있다. 열전모듈은 제조시 수십 개에서 수백 개 이상의 n형 및 p형 열전소자를 알루미나($Al_2O_3$)와 같은 세라믹 기판(substrate) 상에 접합된 동 전극 위에 전기적으로 서로 직렬로 접합시켜 제조한다. 기존의 열전모듈의 제조방법에는 동 전극 위에 위에 Sn합금 분말과 플럭스(flux)의 혼합물인 솔더페이스트를 스크린 인쇄법을 사용하여 동 전극에 도포한 다음, 그 위에 열전소자를 얹고 약 520K의 열풍을 가하여 솔더를 용융시켜 열전소자와 동 전극을 접합시킨다. 스크린 인쇄법에서는 인쇄 압력이 일정하지 않으면, 솔더페이스트 층의 두께가 균일하지 않게 되어 열전소자 접합부의 불량을 유발시킨다. 그러나 열모듈은 단 하나의 접합 불량이 모듈 전체의 열전변환성능에 심각한 영향을 줄 수 있기 때문에 본 연구에서는 이러한 문제점을 해결하기 위해, 솔더페이스트를 도포하지 않고 열전소자를 직접 동 전극과 접합할 수 있는 방법을 고안하였다. 무전해도금을 이용한 니켈층을 형성시킨 $Bi_2Te_3$계 열전소자 표면에 약 $50{\mu}m$의 주석도금층을 전기도금법을 구사하여 형성시켰다. 그 후, wire cutting을 통하여 $3mm{\times}3mm{\times}3mm$의 크기로 절단한 주석도금된 열전소자를 동 전극에 얹고 1.1KPa의 압력을 가하면서 523K의 핫플레이트 위에서 3분간 방치하여 직접(direct) 열압착 접합을 실시하였다. 접합부의 단면을 SEM을 이용하여 관찰한 결과, 동 전극과 열전소자 사이의 계면에 용융 후 응고된 주석층이 결함없이 균일하게 형성된 양호한 접합부를 관찰할 수 있었다. 따라서, 솔더페이스트를 이용하지 않고, 열전소자 표면에 주석도금을 실시한 후, 동 전극과 직접 열압착 본딩을 실시하는 방법은 균일한 접합계면을 얻을 수 있는 새로운 공정으로 기대된다.