• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1070-1076
• /
• 1997

DLC(diamond-like carbon)박막을 RF PCVD법으로 증착하여 일반적인 증착특성과 마찰.마모특성사이의 관계를 알아보기 위해, 증착속도, 박막경도, 내무압축응력 및 박막내의 수소량 측정을 통해 일반적인 증착특성을 조사하였다. 그리고 증착된 박막의 C-H 결합구조와 물질특성 분성을 위해 각각 FTIR 및 Raman분광분석을 행하였다. 박막의 마찰계수와 내마모특성은 Pin-on-disk형 마찰시험기를 이용하여 상기의 증착조건과의 상관관계를 조사하였다. DC self-bais, 즉 충돌에너지가 커지면 박막의 증착속도와 경도는 대체로 증가하고, 박막내의 압축응력은 최대값을 가지다가 다시 감소됨을 알 수 있언ㅆ다. 또한 박막내의 수소량은 급격히 감소하다가 포화됨을 알 수 있었다. 얻어진 박막의 마찰계수는 최소 0.08로 분위기가 dry일 때 더 작으며 내마모성은 이온의 충돌에너지와 밀접한 관계를 가지며 모재인 Si-wafer보다 훨씬 큼을 알수 있었다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.27-30
• /
• 2007

In order to measure the friction coefficient used in sheet metal forming analysis, a friction tester was manufactured and friction tests were performed in various forming conditions. Based on the friction coefficients measured, a mathematical friction model was constructed in terms of lubricant viscosity, blank holding force, punch velocity and sheet roughness. In addition, the effect of the number of forming parameters in the calculation of friction coefficient on the accuracy of sheet metal forming analysis was investigated by comparing the punch loads obtained from the FEM simulation, in which the friction coefficients were determined by a few parameters with the experimental measurement.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.121-121
• /
• 2013

수소로 희석된 벤젠 가스를 반응 가스로 이용하여 합성된 DLC 박막의 마찰 마모 특성을 평가하기 위하여, 일반 대기 환경 및 수중 환경에서 마모 실험을 수행하였다. 일반 대기 환경에서는 박막의 기계적 특성, 마찰 계수 및 마모 거동이 거의 변화하지 않았다. 반면, 수중 환경에서는 마찰 계수가 대기 환경에서보다 안정적으로 평가되었다. 이는 DI-water가 윤활제(lubricant) 역할을 하기 때문으로 예측된다. 또, 수중 환경에서의 마모 실험 결과, 수소가 희석되지 않은 반응 가스를 이용하여 증착 된 DLC 박막의 경우, delamination wear가 상대적으로 많이 관찰되었다. 하지만, 반응 가스에 희석 된 수소량이 증가함에 따라서, 이런 delamination wear가 현저하게 억제됨을 관찰하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.6 s.123
• /
• pp.524-530
• /
• 2007

This paper presents a friction model to realize self-excited vibration of multi-body systems. The friction coefficient is modeled with a spline function in most commercial codes. Even if such a function resolves the problem of discontinuity in friction force, it cannot realize self-excited vibration phenomena. Furthermore, as the relative velocity approaches zero, the friction coefficient approaches zero with the conventional model. So, slip occurs when small force is applied to the system. To avoid these problems a new friction model is proposed in this study. With the new friction model, the self-excited vibration can be realized since the friction coefficient changes with the relative velocity. Furthermore, the slip phenomena could be reduced significantly with the proposed model.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.772-780
• /
• 1987

The normal and tangential belt forces for two types of flat belts are measured and compared. From friction theory, ti was assumed that tangential friction is proportional to the actual contact area $A_{a}$ and $A_{a}$ is proportional to normal pressure P; i.e., $A_{a}$ .var.P$^{n}$ . For a flat belt with cloth backing, the n=2/3 is obtained for the constant of belt surface model. For a flat belt with rubber backing, the n=0.9 to n=1.0 is suggested as a surface model constant. The theoretical equation developed in this paper showed agood with the experimental results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.658-666
• /
• 1992

In developing computer-aided design technology for optimization of stamping die design, it has been an important issue to treat the frictional constraint acting on the blank holder surface. The main goal of this work is to establish database of draw bead restraint force and clarify friction characteristic for various automotive sheet steels, which is essential in developing friction algorithm that can be used for CAD of stamping die design. Draw bead friction tester is used to evaluate the various parameters that affect the draw restraint force and the coefficient of friction for the cold rolled and the coated sheet steels such as drawing rate, lubricant type, surface property of material, etc.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.439-445
• /
• 2005

The tribological properties of ceramics are very important in the application to engineering ceramic parts such as seal rings, pump parts, meter parts, and so on. In this study, the effects of each other purity on the mechanical and tribological properties of alumina and zirconia ceramics were investigated. Sliding distance, sliding speed, contact load. friction coefficient, the amount of worn out material at a certain time, and the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. We obtained the good properties of friction coefficient and wear resistance at the purity 99.7$\%$ of alumina. However, The purity 95$\%$ were great at the wear amount of worn out material.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.241-247
• /
• 2017

Railway bridges with continuously welded rail have a limitation of span length due to track-bridge interaction. In order to overcome this, a sliding slab track system has been developed that comprises with a low-frictional sliding layer between the bridge deck and the track slab to isolate the longitudinal behavior between the bridge and the track. In this study, a real scale track system is prepared to experimentally evaluate the longitudinal frictional behavior. Applied loading rates were 0.2, 1.0, 5.0 and 10mm/min; vertical mass on the track are track slab only, 5,000 and 10,000kg added mass, respectively. Test results showed that the resulting frictional coefficients varied from 0.22 to 0.33. In addition, 10,000 cycle loadings were applied to simulate repetitive sliding to represent 30 years of service life. The frictional coefficient increase was measured and found to be 7% of that of the initial loading stage, which means that the sliding layer is adequate to provide low-frictional behavior for the sliding slab track system. Effects of changes of the frictional coefficient of the sliding layer were analyzed by rail-structure interaction analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6D
• /
• pp.719-726
• /
• 2009

In this study, a series of push-off tests for lean concrete, aggregate, asphalt subbases mainly used in Korea were performed to investigate the friction characteristics between the slab and subbase layers. Use of separation membrane and wet condition of subbase were other parameters in the tests. Horizontal displacements of the slabs and friction coefficients were measured at 1st loading, stable condition (2nd and 3rd loadings), and wet condition (4th loading) by applying 40mm/hour horizontal loadings. Larger maximum friction coefficients were measured in order of the lean concrete, asphalt, aggregate, and subbases using the separation membrane at 1st loading, and in order of the asphalt, aggregate, lean concrete, and subbases using the separation membrane at stable and wet conditions. The friction coefficients of the aggregate and asphalt subbases which did not used the separation membrane decreased by the wet condition while the subbases using the separation membrane were not affected. Additional push-off tests for effects of slab thickness and temperature sensitivity of asphalt will be performed. And, effects of the friction characteristics between the slab and subbase layers on behavior and performance of concrete pavements will be investigated by structural analyses using the test results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.299-307
• /
• 1991

A unified correlation of the interfacial friction factor for air-water and steam-water flows in inclined rectangular channels has been developed. The correlation was expressed in the form of a power law of the liquid and the gas Reynolds number, and the liquid-to-gas viscosity ratio. In addition, a relation between the equivalent roughness and the intensity of wave height fluctuation of the interface has been investigated. A new dimensionless intensity of fluctuation including a liquid film Reynolds number is proposed. It has been shown that the dimensionless equivalent roughness, which is calculated from the Nikuradse equation, can be uniquely related to this dimensionless intensity of fluctuation for both air-water and steam-water flows.