• Journal of Ocean Engineering and Technology
• /
• v.19 no.1 s.62
• /
• pp.44-48
• /
• 2005

The shock absorbers for marine vehicles are very important components to absorbing the shock resulting from driving. Depending on the kinds of vehicles, these essential components, piston and piston rod, must be made of S25C, S45C, and SCM440, must be precisely machined, and assembled by the bolts. Other materials used have been difficult to weld, and could be unstable in quality, by the conventional arc welding. Also, they have been associated with a lot of technical problems in manufacturing. However, using the friction welding technique, such problems will be avoided. These factors have necessitated the domestic development of the marine shock absorber using a friction welding, as well as stimulating a new approach to the study of real-time weld quality evaluation by AE techniques.

• Journal of Power System Engineering
• /
• v.6 no.1
• /
• pp.68-73
• /
• 2002

An opportunity to use the elevated temperature has been recently increasing in various elements of heat facilities or machines such as heat exchanger tubes, pressure vessels, engines of aircraft, boilers and turbines in power plants, and nuclear reactor components, etc. as machinery industry develops. Thus, the development of such elevated-temperature heat-resisting materials and the studies on their elevated-temperature materials friction welding, creep design and analysis have been considered as an important and needful fact. In this paper, friction welding optimization for 1Cr0.5Mo to STS304 and AE applications for the weld quality evaluation were investigated. The important results of this study are as follows : The techniques for dissimilar friction welding optimization of the elevated temperature materials 1Cr0.5Mo and STS304 and its real-time weld quality evaluation by AE were developed, considering on both strength and toughness. Quantitative relationship was identified among welding condition, weld quality and cumulative AE counts.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.109-111
• /
• 2006

In this study, microstructure and mechanical properties for the friction stir welded 2519Al-T87 alloy of the thickness of 38.8mm were studied using DSC, OM, SEM and micro hardness tester. DSC analysis show that GP Zone, ${\theta}'$ and $\theta$ phases in upper part and ${\theta}'$ and $\theta$ phase in lower part of the FSW zone. Recrystallized large grains are observed in HAZ, and elongated small and large grain in the TMAZ. In SZ, very small grains forms by high plastic deformation and heat from friction by tool and specimen.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.614-618
• /
• 2018

The changes in the mechanical properties according to the width of the tool shoulder, rotation speed and moving speed in friction stir welding (FSW) are evaluated using Al 6061-T6. The results indicated that the tensile strength value increases with increasing rotation speed. The higher the moving speed of the tool shoulder, the lower the tensile strength, regardless of the tool type. A higher tensile strength value was generally obtained with a tool shoulder diameter of 12mm (TSD12) than with 8mm. When the moving and rotation speeds exceed a limiting value, a stabilization stage is reached, in which (the tool shoulder diameter?) no longer affects the material properties. At a tool shoulder diameter of 8mm (TSD8), the material properties are decreased and the mixture of material in the welding area is incomplete in comparison with the tool type of TSD12. The tensile strength value is decreased at a rotation speed of 1500 rpm. As a result, a rotation speed higher than the threshold value is needed in order for and the transition temperature to be reached, which allows the complete mixing of the material in the welding area.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.176-178
• /
• 2003

The weld zone of dissimilar formed Al alloy exhibited the complex structure of the two materials and mainly composed of the retreating side material. The mechanical properties were also depended on the dominant microstructure of the weld zone with welding conditions. The different mechanical properties of weld zone with welding conditions were related to the behavior of the precipitates of wrought Al alloy and Si particles of cast Al alloy. The higher mechanical properties of weld were acquired when relatively harder material, wrought Al alloy, was fixed at the retreating side.

• Journal of Welding and Joining
• /
• v.7 no.3
• /
• pp.19-27
• /
• 1989

Both the SS41 steel and the M.E.F(martensite encapsulated islands of frrite) dual phase steel made of SS41 steel by heat treatment were welded by friction welding, and then manufactured machinemade Vnotch standard Charpy impact specimens and precracked with a fatigue system at BM(base metal), HAZ(heat affected zone) and WZ(weld interface Zone). The impact test of them was performed with an instrumented impact test machine at a number of temperatures in constant loading velocity and the dynamic fracture characteristics were studied on bases of the absorbed energy, dynamic fracture toughness and fractography from the test. The results obtained are as follows; At the room temperature, the absorbed energy is HAZ.geq.WZ.geq.BM in case of the M.E.F. dual phase steel: BM.geq.HAZ.geq.WZ in case of the SS41 steel, HAZ.geq.BM.geq.WZ at the low temperature. The absorbed energy is decreased markedly with the temperature lowering; it is highly dependent on the temperature. The dynamic fracture toughness of the M.E.F. dual phase steel is HAZ.geq.WZ.geq.BM at the room temperature; BM.geq.WZ.geq.HAZ below-60.deg. C. Therefore the reliability of friction welding is uncertain at the low temperature(below-60.deg. C). The dynamic fracture toughness of the SS41 steel; HZA.geq.WZ.geq.BM at overall temperature region. The flaw formed by rotational upsetting pressure was shown y SEM; in this region. The absorbed energy per unit area and dynamic fracture toughness were low relative to other region.

• Proceedings of the KWS Conference
• /
• 2008.05a
• /
• pp.8-8
• /
• 2008

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.328-331
• /
• 2007

It was carried out to evaluate microstructure and mechanical properties of friction stir welded(FSW) on magnesium alloys. Two types magnesium alloy was used in this work, AZ31 wrought and AZ91 cast magnesium alloy. Microstructure near the weld zone showed general weld structures such as stir zone(SZ), thermo-mechanically affected zone(TMAZ) and heat affected zone(HAZ). In the AZ91 alloy, the SZ had a fine grain size and $\beta$ phase particles which were well distributed in matrix. It was characterized to redistribute by partial or full re-solution of the $\beta$ phase which is coarse in base metal during FSW processing. The hardness of the SZ slightly increase than the base metal in AZ31 Mg alloy.

• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.77-82
• /
• 2006

In this study, dissimilar friction welding were produced using 15mm diameter solid bar in chrome molybedenum steel(SCM440) to carbon steel(S45C) to investigate their mechanical properties and the relationship between the weld parameters and the nondestructive coefficients, such as AE counts and ultrasonic attenuation coefficient. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond of area and heat affected zone. The specimens were tested as-welded and post weld heat treated(PWHT). The tensile strength of the friction welded steel bars was increased up to 100％ of the S45C base metal under the condition of all heating time. The ductility of PWHT specimens is higher than as-welded.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.21-21
• /
• 2009

현장의 GMA 용접기는 일반적으로 용접기 본체로부터 와이어 송급장치까지의 거리가 약 50m 정도 떨어져 있고 송급장치로부터 토치까지의 거리는 약 3~5m 정도이다. 특히 국산 GMA 용접기의 와이어 송급장치는 DC 모터의 일종인 프린트모터를 사용하고 있으며 제어기는 오픈루프 제어를 하고 있다. 따라서 와이어 송급속도의 변동을 보상할 수 있는 어떤 수단도 장착되어 있지 않다. 또한 송급장치와 토치간 와이어를 안내하는 케이블 도관의 마찰 때문에 토치 끝단에서의 와이어 송급속도가 불규칙해질 수밖에 없다. 용접 시 와이어 송급속도의 순간적인 변동 때문에 용접부의 전류 파형이 매우 불규칙해지고 이 때문에 용융된 용적이 용융풀로 이행하지 못하고 스패터로 비산하는 현상을 발생시킨다. 본 연구에서는 이를 해결하고자 국산 SCR 용접기 및 인버터 용접기와 호환 가능한 디지털 제어형 와이어 송급장치와 Push-Pull 용접 토치를 개발하였다. 또한, 개발된 시스템을 이용하여 정 역 방향 제어기술을 적용하였고 아크 발생 시의 스패터 최소화 공정을 제안하였다. 실험은 SM490A 강재를 사용하여 BOP(Bead On Plate) 용접을 실행하였다. 용접 중 LabVIEW를 이용하여 아크 발생 초기 전류, 전압 그리고 와이어 송급속도를 측정하였고, 고속 카메라를 이용하여 용접현상을 분석하였다. 본 연구를 통해 아크 발생 초기의 스패터를 최소화하는 공정을 도출할 수 있었다. 용접공정 변수인 아크 발생 초기의 와이어 송급속도, 와이어의 역송급 진행거리 그리고 역송급 판단 시점의 용접 전류 값은 실험을 통해 얻을 수 있었다. 또한, 이 연구를 통해 개발된 시스템의 성능을 평가하였다.