• Journal of Korea Water Resources Association
• /
• v.30 no.5
• /
• pp.495-501
• /
• 1997

Pumping power being given, traditional method requires an iteration process for the solution of discharge and pipe diameter. Yoo and Kang (1996) have developed explicit equations for the estimation of discharge and pipe diameter for the cases of uniformly rough pipe on a sloping bed with a pumping power. The use of poser law for the estimation of friction factor enabled to develop the explicit form of equations. Yoo (1995a) has suggested the mean friction factor method for the estimation of friction factor of commercial pipe or composite surface pipe. With the same approach, the present work has developed the explicit equations of discharge or pipe diameter for the general case of commercial pipe on a sloping bed with a pumping power by adopting the mean friction factor method.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1089-1093
• /
• 2010

최근 하천의 자연성 및 생태기능의 향상을 위해 매트류 호안공법의 적용이 증가하고 있다. 이러한 공법이 적용된 호안은 강수 및 하천수의 지속적인 유입으로 인해 앵커핀과 비탈면 간의 마찰력을 저하시킬 수 있다. 마찰력의 저하는 앵커핀의 고정능력을 저하시켜 매트가 들뜨는 현상을 발생시키고, 이로 말미암아 비탈면에 식재된 식생의 고사는 물론 비탈면의 슬라이딩 현상의 발생에 의해 비탈면 붕괴에 까지 이르게 하고 있다. 그러나 현재 호안매트와 함게 시공하는 앵커핀의 적용에 대한 구체적인 기준과 연구가 미흡한 실정이다. 본 연구에서는 매트류 호안제품을 비탈면에 고정시키는 목적으로 사용하고 있는 앵커핀에 대한 인발특성을 파악하고자 하였다. 인발실험에 사용된 앵커핀은 실제 하천호안에 적용되고 있는 상용제품으로 형태가 다른 4가지 type을 실험에 사용하였으며, 앵커핀의 관입깊이(170mm, 250mm) 별로 인발실험을 실시하였다. 실험에 사용된 인발장치는 인발부에 로드셀을 장착하여 앵커핀과 결합이 가능하도록 하였으며, 인발시 발생하는 계측 값을 컴퓨터를 통해 출력이 가능하도록 제작하였다. 실험결과 4가지 형태의 앵커핀에 대한 관입깊이별 형태별 인발특성을 파악할 수 있었으며, 비탈면 및 매트의 고정효과가 우수한 앵커핀의 형태에 대해서도 파악할 수 있었다. 관입깊이별 최대 인발력은 두 변위(170mm, 250mm) 모두 Type 4가 337N, 594N 으로 가장 큰 인발력을 가지는 것으로 측정되었으며, 변위에 의한 인발력의 증가는 Type 2가 138%로 가장 큰 폭의 증가 값을 보였다. 또한 토양과 앵커핀의 마찰력 향상을 위해 하부가 돌출된 형태로 제작된 Type 2와 Type 4가 상대적으로 실험 후반부에서 최대 인발력이 발생하고 인발지속시간이 길게 나타나는 것으로 볼 때, 인발저항은 앵커핀 하부의 돌출면적에 영향을 받는 것으로 판단된다.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.3
• /
• pp.61-69
• /
• 2022

In this study, a large-scale direct shear test was performed to evaluate the shear characteristics of the pile-soil interface according to the fines content and confining pressure conditions as a reasonable evaluation method of the pullout resistance performance of pile considering the soil conditions. It was found that the shear stress was greatly generated under the conditions of high normal stress and low fines content. In addition, the maximum shear stress was found to be rather large under the conditions of the same normal stress and fines content, when pile surface had high roughness. The internal friction angle decreased at the pile-soil interface, when the fines content in the ground increased. On the other hand, the cohesion decreased under the condition of high fines content. And the internal friction angle and cohesion were large regardless of the fines content in the model ground, when the roughness of the pile surface was high.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.49-52
• /
• 2008

The plain and simple shape water front structure were designed and installed for wave protection and wave resistance. But the installation of these plain and simple structure cause deficiency of environmental affinity. Also the resonance phenomena from the reflective wave and shipwave of the harbor incident wave caused high tide and wave, consequently maintaining the tranquility of inside harbor, give difficulty for mooring the ship and loading-unloading, increase the possibility of ship collision at the quray wall and landing place To solve these problems, we develop the environmentally friendly wave dissipation block. And installation efficiency, stability of the blocks through experiment of C.E Block Joint.

• Geotechnical Engineering
• /
• v.12 no.2
• /
• pp.107-114
• /
• 1996

A series of shear tests is performed to measure friction coefficients of the interface between different reinforcements and weathered granite soils. The reinforcements tested are smooth steel strip, Paraweb(friction tie) and geotextile with rough surface, while the weathered granite soils are composed of different, grain size distribution. Soils are compacted with the energy of 95% modified AASHTO and fully saturated before testing to simulate the worst site condition. Because of characteristics of the direct shear apparatus, shear strength is obtained in terms of drained condition. Test results show that the more fines the soils contain, the larger ratio of friction coefficient ($\mu=\frac{tan{\delta}}{tan{\Psi}}$) is obtained. Also the ratios are much higher for the Friction tie and the geotextile compared to the smooth steel strip. Those suggest that even weathered granite soils with 36% fines are possible to use as backfill of reinforced earth structures for the two reinforcements when a drainage system is provided.

• The Journal of the Acoustical Society of Korea
• /
• v.41 no.4
• /
• pp.389-396
• /
• 2022

This paper aims to identify the causes and mechanisms of contraction-expansion noise in refrigerators and proposes noise reduction methods. Contraction-expansion noise generated in refrigerators is mainly due to stick-slip phenomenon occurring on the contact surface between inner parts. Friction experiments were conducted to identify the factors causing the stick-slip phenomenon. Furthermore, the vibration level of the internal components was measured to determine the characteristics and location of the contraction-expansion noise. Based on the experimental results, experiments have been conducted to verify the noise characteristics for each factor. From this, it was confirmed that the friction experiment and the refrigerator contraction-expansion noise generation location and frequency were the same. The vibration level also increased as the vertical force was increased due to load loading. Also, it was confirmed that the contraction-expansion noise was reduced when the surface roughness was increased. Therefore, it was concluded that increasing the surface roughness of the contact surface in the same way as the results of the friction experiment was the method of reducing contraction-expansion noise.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.7
• /
• pp.596-604
• /
• 2011

To improve the total efficiency of centrifugal compressor, it is necessary to reduce the disk friction loss, which is defined as the power loss. In this study, the disk friction loss due to the axial clearance and the surface roughness effect is analyzed and proposed the new empirical equation for the reduction of the disk friction loss. The rotating reference frame technique and the 2-equation k-${\omega}$ SST model using commercial CFD code FLUENT is used for the steady-state analysis of the centrifugal compressor impeller. According to CFD results, the disk friction loss of the impeller is more affected by the surface roughness than the change of the axial clearance. For the minimization of the disk friction loss on the centrifugal compressor impeller, the magnitude of the axial clearance should be designed to the same size compare with theoretical boundary layer thickness and the surface roughness should be minimized.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3A
• /
• pp.513-521
• /
• 2006

Many studies have been conducted on the high tension bolt friction connection in the view of the field practice. Those effort, however, unfortunately have not been appropriately applied in the design specifications. Recently, particularly for steel bridges, rationalization of design takes greater attention from designers and hence, demand on rationalization of high tension connection becomes more significant. The purpose of this study is to suggest direction for the rationalization of high tension bolt connection and to also provide fundamental information for the improvement of the design specifications. In order to accomplish the purposes, the design specifications in Korea was analyzed and compared with other specification from abroad, and was studied one of the most important factors including slip coefficient, and the specifications on the size of bolt holes. The effect of over-sized bolt hole and the reduction of axial force on bolt was evaluated through the experimental studies on the slippage of the high tension bolt connections. Other research topics included herein includes the difference of slip coefficients, the effect of over-sized bolt holes and the gap distance of members, and the application of filler plate and corrosion protected bolts. From the research results, it is known that the specifications in Korea apply a constant slip coefficient with respect to the contacted surface conditions while various coefficients are available depending on the contacted surface conditions. Therefore, it is recommended that the specifications in Korea also develop and detail the slip coefficient which can appropriately take account of the variation of the contacted surface conditions. It is also suggested that the limitation abroad on the over-sized bolt hole may be applied for enhancing the effectiveness of construction.

• Explosives and Blasting
• /
• v.37 no.4
• /
• pp.26-35
• /
• 2019

In designing a gravity-type anchorage of earth-anchored suspension bridge, the contact friction between a blasted rock mass and the concrete anchorage plays a key role in the stability of the entire anchorage. Therefore, it is vital to understand the shear behavior of the interface between the blasted rock mass and concrete. In this study, a portable 3D LiDAR scanner was utilized to scan the blasted bottom surfaces, and rock surface roughness was quantitatively analyzed from the scanned profiles to apply to 3D FEM modelling. In addition, based on the 3D FEM model, a three-dimensional dynamic fracture process analysis (DFPA-3D) technique was applied to study on the shear behavior of the interface between blasted rock and concrete through direct shear tests, which was analyzed under constant normal load (CNL). The effects of normal stress and the joint roughness on shear failure behavior are also analyzed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.166-171
• /
• 1993

절삭공구에의한 절삭가공은 오늘날 가장 보편화된 가공기술중의 하나이다. 그런데, 최근들어 각종 첨단산업의발전과 함께 초정밀 부품제작이 필수선결 조건으로 부상하고 있으며, 이에대한 해결방안중의 하나로 초정밀가공 기 술로 크게 대두되고 있다. 최근 컴퓨터 기술의 발달에 따라 구조해석분야의 해석방법론의 개발 및 보완에 힘입어 Klemecki(1973)에 의해유한요소법을 이용한 Chip생성기구 해석에 관한 연구가수행되었으며, Stevenson(1983) 등에의해단열조 건하에서 변형률과 온도 상태에서의 Chip형상, 잔류응결-변형율에 대한 연구가 이루어졌다. 본 연구에서는 유한요소법을 이용하여 미소절삭기구를 모델링하고, 절삭인자규명을 중심으로 응력-변형률 해석을 실시함으로써, 미소절삭시의 Chip 생성기구 및 전단면 생성 원리, 공구와 Chip간의 마찰기구의 고찰을 통해기본 Mechanism 이해와 적절한 절삭유한요소모델 제시의 기초자료로 삼고자 한다. 특히 본 보고서에서는 미소 절삭기구의 적정한 Constitutive Deformation Law 마찰계수 등 주요절삭인자변경에 따른 미소절삭기구 해석에 주안점을 두어 연구한 결과를 기술하였다.