• Journal of Ocean Engineering and Technology
• /
• v.22 no.6
• /
• pp.35-40
• /
• 2008

The effect of counterpart roughness on abrasive wear characteristics of side plate materials of FRP ship, which were composed of glass fiber and unsaturated polyester resin composites, were investigated at ambient temperature by pin-an-disc friction test. The friction coefficient, wear rate and cumulative wear volume of these materials against SiC abrasive paper were determined experimentally. The wear rate of these materials decreased rapidly with sliding distance and then maintained a constant value. It was increased as counterpart roughness was rougher in a wear test. The cumulative wear volume tended to increase nonlinearly with sliding distance and depended on applied load and sliding speed for these composites. It could be verified by SEM photograph of fracture surface that major failure mechanisms were overlapping layers, microcutting, deformation of resin, delamination, and cracking.

• Journal of Power System Engineering
• /
• v.15 no.5
• /
• pp.77-82
• /
• 2011

SiC particulate reinforced Al matrix composites with different SiC volume fractions were fabricated by thermal spray process. And the dry sliding wear test were performed on these composites using the applied load of 10 N, rotational speed of 30 rpm, radius of rotation 15 mm. Wear tracks on the Al/SiC composites were investigated using scanning electron microscope(SEM) and energy dispersive spectroscopy (EDS). It was observed that wear behavior of Al/SiC composites and formation of MML was changed dramatically according to reinforcement volume fraction.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.123-128
• /
• 2009

The effects of temperature and initial crack length on the impact fracture behavior for the side plate material of FRP ship were investigated. And the effects of the counterpart roughness and sliding distance on the volumetric wear of same material were investigated as well. Impact fracture toughness of GF/PE composites displayed maximum value when the temperature of specimen is room temperature and $50^{\circ}C$, and with decreasing the temperature of specimen, impact fracture toughness decreased. Impact fracture energy of GF/EP composites decreased with increasing the initial crack length of specimen, and this value decreased rapidly when the temperature of specimen is lowest, $-25^{\circ}C$. It is believed that sensitivity of notch on impact fracture energy were increased with decreasing the temperature of specimen. With increasing the sliding distance, the transition sliding distance, which displayed different aspect on the friction coefficient and the volumetric wear loss, were found out. Counterpart roughness had a big influence on the wear rate at running in period, however the effect of counterpart roughness became smaller with sliding speed increase in. Volumetric wear loss were increased with increasing the applied load and the counterpart roughness.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.9 s.114
• /
• pp.904-911
• /
• 2006

A modified energy method for the fretting wear of the steam generator tube is proposed to calculate the wear-out depth between the nuclear steam generator tube and its support. Estimation of fretting-wear damage typically requires a non-linear dynamic analysis with the information of the gap velocity and the flow density around the tube. This analysis is very complex and time consuming. The basic concept of the energy method is that the volume wear rate due to the fretting-wear phenomena Is related to work rate which is time rate of the product of normal contact force and sliding distance. The wearing motion is due to dynamic interaction between vibrating tube and its support structure, such as tube support plate and anti-vibration bar. It can be assumed that the absorbed work rate would come from turbulent flow energy around the vibrating tube. This study also numerically obtains the wear-out depth with various wear topologies. A new dissection method is applied to the multi-span tubes to represent the vibrational mode. It turns out that both the secondary side density and the normal gap velocity are important parameters for the fretting-wear phenomena of the steam generator tube.

• Tribology and Lubricants
• /
• v.35 no.4
• /
• pp.244-266
• /
• 2019

The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.

• Composites Research
• /
• v.33 no.5
• /
• pp.241-246
• /
• 2020

In this study, aluminum (Al) alloy matrix composites in which B₄C particles were uniformly dispersed was manufactured through stir casting followed by hot rolling process. The microstructure, mechanical properties, and wear resistance properties of the prepared composites were analyzed. The composite in which the 40 ㎛ sized B₄C particles were uniformly dispersed increased the tensile strength and improved wear performance as the volume ratio of the reinforcement increased. In the case of the 20 vol.% composite, the tensile strength was 292 MPa, which was 155% higher than that of the Al6061. As a result of the wear resistance test, the wear width and depth of the 20 vol.% B₄C/Al6061 composites were 856 ㎛, and 36 ㎛, and the friction coefficient was 0.382, which were considerably superior to Al6061.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.2
• /
• pp.261-270
• /
• 2001

This study was performed to evaluate wear characteristics of light-cured composites when opposed by human enamel. Seven light-cured restorative composites were selected and enamel cusps sectioned from premolars. All samples were stored in distilled water at $37^{\circ}C$ for 10 days. 68.6 N of weight was loaded during the test. The measurements of vertical loss of enamel cusps, weight loss and volume loss of composites, and SEM observations of the polished and abraded surfaces were made after 30,000 cycles. The results obtained were summarized as follows; 1. The highest hardness value of 70.4 was observed in the Spectrum group and the lowest value of 19.8 was observed in the Heliomolar group. Results of Tukey test showed that an overall significant difference was indicated except the Spectrum, Z100 and Clearfil AP-X groups(p<0.05). 2. Enamel showed the good abrasion resistance against the Heliomolar group of microfilled composite and the Palpique Toughwell group containing the submicron hybrid type spherical fillers. 3. The abrasive wear resistance of hybrid composites was improved with the decrease of mean particle size and hybrid of submicron particle fillers. 4. SEM observation of worn surfaces revealed the protrusion, attrition and missing of fillers, cracks developing and delamination in the matrix.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.115-118
• /
• 2003

편성물은 루프형태로 얽혀있는 조직의 구조적 특성상 제편 과정에서 필요한 형태로의 성형이 용이해서 제품의 다양화를 기대할 수 있고 우수한 신축성과 드레이프성, 공기함유율, 구김안정성 둥이 우수하여 인체의 여러 가지 활동에 따른 구속감이 적어서 의류용 뿐만 아니라 신발 소재, 산업용 보강제등 그 활용도가 아주 높은 소재이다. 특히 경편성물은 직물과 편성물의 중간체적인 성향을 나타내고 있어서 제품생산시간을 단축할 수 있고 질적인 면에서도 직물과 아주 유사하여 후가공 처리에 유용한 소재이다[1]. (중략)

• Tribology and Lubricants
• /
• v.34 no.4
• /
• pp.146-159
• /
• 2018

This paper presents a wear analysis procedure for calculating the wear of journal bearings of a four-strokes and four-cylinder engine operating at a constant angular crank shaft speed during firing conditions. To decide whether the lubrication state of a journal bearing is in the possible region of wear scar, we utilize the concept of the centerline average surface roughness to define the most oil film thickness scarring wear (MOFTSW) on two rough surfaces. The wear volume is calculated from the wear depth and wear angle, determined by the magnitude of each film thickness on a set of oil films with thicknesses lower than the MOFTSW at every crank angle. To calculate the wear volume at one contact, the wear range ratio during one cycle is used. The total wear volume is then determined by accumulating the wear volume at every contact. The fractional film defect coefficient, asperity load sharing factor, and modified specific wear rate for the application of the mixed-elasto-hydrodynamic lubrication regime are used. The results of this study show that wear occurs only at the connecting-rod big-end bearing. Thus, simulation results of only the big-end bearing are illustrated and analyzed. It is shown that the wear volume of each wear scar group occurs consecutively as the crank angle changes, resulting in the total accumulated wear volume.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06a
• /
• pp.22-28
• /
• 1989

유압베인펌프는 토출유량이 많고 소형으로 동력밀도는 높으나 토출압력면에스는 피스톤식 펌프에 뒤지기 때문에 발생압력의 고압화에 대한 연구가 계속되어 왔다. 유압장치의 경제적인 압력으로서 $300kgf/cm^2$가 제시되어 있는 가운데, 유압베인펌프의 고압화의 연구가 진행중에 있는 점, 또한 최근들어 에너지 절약의 일환으로 펌프의 수명연장 문제가 거론되어 지고 있는 점, 물에 타기 어려운 난연성유압 작동유를 사용할 경우 마찰증대 및 마모성능이 저하하는 점 등의 이유에서 유압베인 펌프의 마찰, 윤활문제가 중요시 되어지고 있다. 특히 펌프의 체적효율을 높이는 것과 마찰, 마모를 저하시키는 것과는 서로 상반된 관계에 놓여있기 때문에 문제의 해결에 어려움을 갖고 있다. 이와같은 모순을 해결하기 위해서는 베인과 캠링사이의 슬라이딩부분의 윤활상태를 파악하지 않으면 안된다. 그러나 베인의 선단부에는 10-20ms의 짧은 시간동안에 수백기압의 압력이 변화하기 때문에 지금까지 확실한 작용력의 파악이 어려워 이 분야의 윤활상태 파악에 관한 연구는 거의 이루어지지 않고 있다. 베인과 캠링간의 윤활상태를 윤활공학적 관점에서 보면 변동하중 상태에서의 슬라이딩 탄성유체윤활상태 또는 혼합윤활상태에 있는 것으로 판단되어지는데, 이와같은 여러가지 어려운 조건 때문에 윤활상태를 파악하는데, 어려운점이 뒤따르게 된다. 위와 같은 배경에 착안하여 본 연구에서는 유압베인펌프를 모델화하여 변동하중상태에서 실험이 가능한 장치를 제작, 사용하여 베인 선단 슬라이딩부분의 윤활상태를 파악하였다.