• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.811-816
• /
• 2006

The single layered magnetic thin films with anisotropic magnetoresistance behavior have advantage on micro integration due to their low cost in manufacturing. Although the conventional MCo (M=Cu, Ag) amorphous ribbons using a rapid solidification process have showed appropriate for magnetic property for bulk devices, they are not appropriate for micro-scale devices due to their brittleness. We prepared the thermal evaporated 100 nm-thick $Cu_{1-x}Co_x\;and\;Ag_{1-x}Co_x(x=0.1{\sim}0.7)$ films on silicon wafers and investigated the magnetic property of the as-depo films such as magnetization and magnetoresistance ratio. We confirmed that the maximum MR ratio of 1.4 and 2.6% at the external field of 0.5 Tesla in $CuCo_{30},\;AgCo_{40}$ films, respectively. Our result implies that AMR may be slightly less than those of the conventional CuCo and AgCo ribbons due to surface scattering, but their AMR ratio be enough for micro-scale application with easy integration compatibility for the process without surface oxidation.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.15-20
• /
• 2019

The agitator is an important industrial instrument widely used for mixing various solutions in the industrial field. In this study, the optimized design of the helical ribbon type impeller, which is mainly used for the stirring of the high viscosity solution, is carried out by CFD analysis. For this purpose, an index for evaluating the agitation performance is newly defined and an optimization design process is performed through a multiphase computational fluid dynamic analysis. From these results, it is understood that the stirring performance is maximized in the case of the helical ribbon impeller under given operating conditions when the width is 7.5 mm, the height is 160 mm and the turn is 1.

• Electrical & Electronic Materials
• /
• v.24 no.10
• /
• pp.3-9
• /
• 2011

• RED RIBBON
• /
• s.40
• /
• pp.34-35
• /
• 2001

• Korean Journal of Materials Research
• /
• v.7 no.4
• /
• pp.287-294
• /
• 1997

(NdㆍDy)-(FeㆍCoㆍAIㆍM)-B 합금에 Sn,Mo등을 첨가하여 그에 따른 미세구조와 열적안정성 및 자기적 특성 변화를 조사하였다. Sn과 Mo의 첨가는 (NdㆍDy)-(FeㆍCoㆍAIㆍM)-B 합금리본의 큐리온도를 크게 향상시켰으며 자기특성, 특히 보자력을 1KOe이상 증가시켰다. 그리고 이러한 현저한 보자력 증가는 입계형 defect인 disturbed grain boundary defect에 기인하는 것이라 판단되었다. 또한 Sn과 Mo 첨가원소는 irreversible loss를 각각 4%와 6% 감소시켜 리본자석의 열적안정성을 향상시켰다. 이는 Sn과 Mo의 첨가가 보자력을 크게 증가시켰기 때문이다. 한편 (NdㆍDy)-(FeㆍCoㆍAIㆍM)-B 리본자석들의 열저항온도(heat resistance temperature)는 irreversible loss와 직선관계를 이루었다.

• RED RIBBON
• /
• s.18
• /
• pp.10-11
• /
• 1997

어떠한 가능성이든지 국내 바이러스들이 한 개의 군으로 몰리는 현상은 집중적인 조사를 필요로 한다.

• RED RIBBON
• /
• s.55
• /
• pp.8-9
• /
• 2003

김홍신 국회의원의 '한국형 에이즈' 발표 이후 한국인은 subtype B형에만 취약하고 그 외의 타입에 대해서는 저항력이 있는 것으로 오해하고 있다. 왜 한국인에게는 subtype B형이 많은가?

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.175-184
• /
• 1993

Abstract Co-and/or AI-added Nd-Fe-B-based magnetic alloys were fabricated by using vacuum induction melting frunace, and melt-spun ribbons were made of the magnetic alloys with single roll rapid quenching method. The variation of magnetic properties of the melt-spun ribbons as a function of Cuwheel velocity (Vs) were investigated. Bonded magnets were made of the optimally quenched ribbon fragments, and the magnetic properties of the melt-spun ribbons and the bonded magnets were studied, relating to the microstructure and crystalline structure. Cu-wheel surface velocity had a strong effect on the magnetic properties of the melt-spun ribbons, and the maximum properties were obtained around Vs =20m/sec. The optimally quenched ribbon had a cellura-type microstructure, in which fine N$d_2$F$e_14$B grains were surrounded by thin Nd-rich phase. In case of a 2.1at% AI-added melt-spun ribbon, the magnetic properties were as follows: iHc, Br, and (BH)max were 15.5KOe, 7.8KG and 8.5MGOe respectively. And resin bonded magnets were fabricated by mixing optimally quenched ribbon fragments with 2.5wt % polyamide resin, compacting and binding at room temperature. The iHc, Br and (BH)max of bonded magnet were lO.2KOe, 4.4KG and 3.3MGOe respectively. And hot-pressed magnets were made by pressing the overquenched ribbons at high temperature. The magnetic properties of hot-pressed magnets were better than those of bonded magnets, and when the holding time was 8 minutes, the iHc, Br, and (BH)max of the hot-pressed magnet were 1O.8KOe, 7.3KG and 8.0MGOe respectively. Domain structure was mainly maze pattern, which means that the easy magnetization axis could be aligned, and the domain width of the hot-pressed magnets was smaller than that of bonded magnets.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.599-605
• /
• 2019

Ferrite cores are used as a soft magnetic material in the fabrication of couplers for inductive powerline communication (PLC). However, it is difficult to adjust the size freely according to the power-line and power-grid environment. In this paper, we report that a nano-crystalline alloy with higher permeability than ferrite can be used as an inductive coupler for non-contact PLC. Since nano-crystalline are produced in the form of a thin ribbon, the size of the coupler can be freely controlled by the number of ribbons wound on the toroidal core. It was fabricated with induction type coupler and showed to be suitable for non-contact power line communication. Experimental results show that the communication bandwidth is 45 Mbps for 100 m and 8 Mbps for 200 m under the current fluctuation of less than 100 A, and the reception ratio is 100%.

• Composites Research
• /
• v.34 no.6
• /
• pp.400-405
• /
• 2021

In this study, a composite material frame was designed to increase the energy harvesting efficiency of polyvinylidene fluoride (PVDF) ribbon harvesters which are installed inside smart shoes. In order to minimize the amount of deformation in the load direction of the frame, it was designed using carbon continuous fiber composites and its complex shaped structure was manufactured using a 3D printer. In order to calculate the amount of deformation of the insole and midsole of the shoes under the condition of the load generated during walking, the insole and midsole were modeled using the distributed spring elements. Using finite element analysis, the elongation of ribbon-type harvesters mounted on smart shoes was calculated during walking. It is expected that the predicted elongation of the harvester can be utilized to increase the energy harvesting efficiency of smart shoes.