• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.53-63
• /
• 2016

Wheel dynamometers are used to measure dynamic load that is conveyed from the road to a vehicle while driving. In this paper, two types of six-component wheel dynamometers utilizing shear deformation and bending deformation were designed and evaluated. Prior to designing the shear and bending type wheel dynamometers, the shear and bending deformation behaviors of the basic structure of the wheel dynamometer itself were analyzed using finite element analysis. Strain analysis was performed repeatedly in order to obtain a similar output sensing strain for each load component. The design was modified with a bridge circuit in order to minimize coupling strain. The results indicated that the shear type dynamometer was expected to obtain stable characteristics due to uniform strain distribution while the bending type dynamometer was expected to obtain high-quality sensitivity performance due to consistent output sensitivity.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.6 no.2
• /
• pp.23-30
• /
• 2012

In this study, we developed a wireless rehabilitation auditory feedback gait training system for symmetrical weight-bearing in patient with CVA. The device consists of an instantaneous shoe equipped with two load-cell sensors. Auditory feedback can be applied according to the weight-bearing. For gait patterns analysis, cadence, walking velocity, stance/swing phase ratio and gait cycle were examined. The clinical test with six healthy volunteers and two hemiplegic patients was performed applying the auditory feedback system. Both normal subjects and hemiplegic patients were increased strength on weight-bearing in affected limb, walking velocity, and cadence after biofeedback device. Also, the stance time with weight-bearing was increased while the swing time was decreased in gait phase. It can be expected that by using the feedback system, the patient with lower limb disorder will be able to reach a better quality of weight-bearing during gait.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.2
• /
• pp.69-73
• /
• 2015

In this study, a method for estimating the amount of urination for men, was suggested and its performance was evaluated. This study is a preliminary one for the development of a health monitoring system that needs un-constraining, non-intrusive and long-term measurements in daily life. To estimate the amount of urination, a wide weighing plate with load cell was built and the difference in a man's weights between before and after urination was measured while he was standing on the plate. The results showed that the amount of urination can be estimated with the measured weight difference under the condition of mild movements. The largest measurement error of the suggested method was 40g, which means that this method can be applied to health monitoring in daily life. It is expected that the results of this study will be the basis for developing practical un-constraining and non-intrusive health monitoring system for daily use at home.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.34-44
• /
• 2015

A hydraulic tensile test machine (HSTM) is one of the devices used to obtain the flow stress of a material during high-speed elongation. This paper first describes some features of a newly built HSTM. The improvement histories of the upper and lower jigs, which are the most vital parts of the HSTM, are also presented. We have frequently witnessed test failures with 1st generation jigs and specimens due to slip between the jig and specimen. 2nd generation jigs provide more stable test results, but the use of a longer upper jig induces excessive vibration and consequently makes it difficult to attach an environment chamber. 3rd generation jigs have some advances in terms of the symmetric fastening between the upper jig and specimen, as well as an exemption from direct contact between the lower jig and specimen. The performance of an environment chamber is verified by high and low temperature tests. A high-speed displacement measurement system is introduced based on a high-speed camera and motion-tracking software with aid of a surface grid device for the specimen.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.11
• /
• pp.18-25
• /
• 2006

Unsteady aerodynamic force measurements were carried out in order to investigate the effects of phase difference of a dragonfly-type model with two pairs of wing. A load-cell was employed to measure the aerodynamic force generated by a plunging motion of the dragonfly-type model. The dragonfly-type model has a dynamic similarity with real one, and incidence angles of fore- and hind-wing are 0° and 10°, respectively. Other experimental conditions are as follows: The freestream velocity was 1.6 m/sec and corresponding chord Reynolds number was 2.88×103, and phase differences of fore- and hind-wing were 0°, 90°, 180° and 270°. The variation of aerodynamic coefficients during one cycle of the wing motion is presented. Results show that the lift is generated during the downstroke motion and the drag generated during the hind-wing‘s downstroke motion with the lift generation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.10
• /
• pp.846-852
• /
• 2012

The present paper is the preliminary study of the development of a morphing aircraft wing and investigates experimently the aerodynamic characteristics of a base airfoil and a morphing airfoil. The wind tunnel tests are conducted for a base Clark-Y airfoil, an airfoil with a mechanical flap, and a morphing airfoil. Lifts, drags, and pitching moments are measured by using a three-axis load cell and they are calibrated by considering solid blockage and wake blockage. The wind tunnel tests are conducted for various air speeds, Reynolds' numbers, and angles of attack. The experimental results show that the aerodynamic characteristics of the morphing airfoil in lift-drag and lift-pitching moment are better than those of the airfoil with a mechanical flap.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.3
• /
• pp.1078-1084
• /
• 2011

In design of sport footwear, bending stiffness of its toe part is an important factor though it can be hardly measured. This paper introduces a device for measuring the bending stiffness. The device is simply designed with aluminum frames, one AC motor, two load-cells, one encoder and control hardwares. The mechanism measuring the bending moment of a shoe is described. Then, it was used to observe how the midsole material and design of a sports shoe affect on its bending stiffness. For the experiments, various specimens prepared, where each midsole of the specimens is different in terms of material, thickness and hardness. With those specimens, experiments were performed by using the device and then the bending stiffness was computed by applying the least square curve fitting after the bending moment data were measured. The specimen with Poly-urethane(PU) midsole has the higher bending stiffness than the one with Phylon(PH) midsole, and the midsole thickness affects more on the bending stiffness than the midsole hardness. Based on those results, it can be concluded that the measurement device can provide consistent bending stiffness data to sports footwear and the bending stiffness of a footwear measured by the developed device can be used as a major parameter in the footwear design.

• Tunnel and Underground Space
• /
• v.15 no.1 s.54
• /
• pp.55-60
• /
• 2005

In this study, the 1/20 reduced-scale experiments using Froude scaling were conducted to investigate the effect of longitudinal ventilation on the variation of burning rate in tunnel fires. The methanol square pool fires with heat release rate ranging from 3.57 kW to 10.95 kW were used. The burning rate of fuel was obtained by measured mass using load cell and temperature distribution were measured by K-type theomocouples in order to investigate smoke movement. The wind tunnel was connected with one side of the tested tunnel, and logitudinal ventilation velocity in the tested tunnel was controlled by power of the wind tunnel. In methanol fire case, the increase in ventilation velocity decreased the turning rate due to the direct cooling of fire plume. For the same dimensionless velocity(V), homing rate decreased as the size of pool fire increased.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.1
• /
• pp.89-100
• /
• 1994

The current test procedure for transfer length, which determine transfer length by measuring concrete strain, has an actual bond stress state in the prestressed pretensioned member : however, it is difficult to determine the bond properties of maximum bond stress and bond stiffness with this method. It is also difficult for design engineer to understand and select a correct safety criterion from the widely distributed results of such a ransfer test alone. An alternative testing procedure is provided here to determine the bond properties without measuring the concrete strain. In this test the bond stress is measured directly by creating a similar boundary condition within the transfer length in a real beam during the transfer of prestressing force. The prestressing force was released step by step by step from the unloading side. The release of force induces a swelling of the strand at the unloading side of concrete block, bonding force in the block, and a bond slip of the strand toward the other side of the block. Two center-hole load cells are used to record the end loads until the point of general bond slip(maximum bond stress). It is suggested that this test procedure be performed with the ordinary transfer test when determining the transfer length in a prestressed, pretensioned concrete beam.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.859-864
• /
• 2014

This experimental study investigates the effects of a downstream cylinder in the wake change on upstream object's diameter. A V-shaped object is placed in the upstream of the test section and a circular cylinder containing a load-cell is placed in the downstream. The velocity distribution of the wake generated from the upstream object with a change in its diameter is investigated. Further, the fluctuation in the lift coefficient and Karman-vortex emission frequency with a change in the position of the downstream cylinder is examined. The study results reveal the following. i) The flow velocity in the wake is smaller than that in the main stream. ii) The lock-in phenomenon occurs when the diameter of the upstream object is larger than that of the downstream cylinder. iii) To generate maximum fluctuating lift force of the downstream cylinder in the wake, the position of the downstream cylinder must be moved with changing diameter of the upstream object together.