• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.7
• /
• pp.667-672
• /
• 2016

This study presents results of an experimental investigation of the laser-arc, hybrid, butt welding process of SS400 structural steel. Welding parameters including laser power, welding current and speed were varied in order to obtain one-pass, full-penetration welds without defects. The conditions that resulted in optimal beads were identified. After welding, hardness measurements and microstructure observations were carried out in order to study weld properties. The mechanical properties of both the base material and welded specimen were compared based on the results of tensile strength measurements. The yield and tensile strengths were found to be similar.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1061-1068
• /
• 2012

These days, world wide interest about global warming and environmental pollution and exhausting fossil fuel which have been main energy source in all around the world. So many country have tried to find out the solution by investing new & renewable and clean energy. Therefore LNG have been widely used as a substitution of fossil fuel and clean energy that emits less pollutant like SOx, NOx. Therefore LNG consumption has been quickly raised and LNG carriers have been getting larger for decades. In this study, high power fiber laser was used for welding of stainless steel for LNG carrier to increase its productivity. Used material was STS316L which has low carbon less than 0.03% and its thickness was 8 mm. We carried out bead, lap and butt welding by using the fiber laser which has maximum power up to 5kW. As a result, we could find out that lap and butt joint was possible at welding speed of 2.0m/min and 3.0m/min respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.89-94
• /
• 2015

This study was conducted to compare the laser weldability of boron steel and hot-stamped steel. In general, boron steel is used in the hot-stamping process. Hot-stamping is a method for simultaneously forming and cooling boron steel in a press die after heating it to the austenitizing temperature. Hot-stamped steel has a strength of 1500 MPa or more. Thus, in this study, the laser weldability of boron steel and thet of hot-stamped steel were investigated and compared. A continuous wave disk laser was used to produce butt and lap joints. In the butt welding, the critical cooling speed at which full penetration was obtained in the hot-stamped steel was lower than that of boron steel. In the lap welding, the joint widths were similar regardless of the welding speed when full penetration was obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.10
• /
• pp.901-906
• /
• 2016

The purpose of this study is to improve productivity by implementing one-pass full penetration welding using laser-arc hybrid welding for AH36. On increasing the thickness of the plate, a higher power of laser and arc was required to obtain full penetration. However, increasing the power of heat source caused undercut defects at both ends of the bead. This undercut was prevented by controlling the parameters of welding voltage and pulse correction. Hardness measurement and tensile test were conducted to apprehend the mechanical properties of weld. Also, by carrying out the microstructure observation for laser and arc regions, microstructural properties were understood.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.113-113
• /
• 2009

세계적으로 환경문제에 대한 관심이 커짐에 따라 연료 효율 향상과 매연을 줄이기 위해 차량 경량화 요구가 증가하는 동시에 안전 규제가 강화되고 있어 높은 강도를 가지는 소재의 적용이 증가하고 있다. 충돌 시 차량 구조를 유지시켜주는 범퍼나 B-필러와 같은 부품에 1500MPa급의 초고강도강이 적용되고 있으며 레이저 용접이 가지는 장점이 많이 알려지면서 그 사용이 증가하는 추세이다. 따라서 레이저 용접에 의한 초고강도강의 용접 특성에 대한 연구가 필요하다. 본 연구에서는 1500MPa급 초고강도강의 레이저 맞대기 용접을 실시하여 단면, 경도 측정, 인장시험을 통해 용접부 특성을 파악하였다. 파이버 레이저와 디스크 레이저를 사용하여 각각의 레이저빔 직경 변화에 따른 입열량 변화에 따라 용접성에 미치는 영향에 대해 알아보았다.

• Journal of Welding and Joining
• /
• v.14 no.3
• /
• pp.20-28
• /
• 1996

고밀도 에너지를 열원으로 이용하는 고출력 레이저로는 CO$_{2}$레이저와 Nd;YAG 레이저가 있다. 레이저는 열가공임에도 불구하고 빔의 스폿경을 작게하여 높은 에너지 밀도($10^{6}$ W/cm$_{2}$ 이상)을 얻을 수 있으므로 열영향이 작고 작은 변형범위내에서 용접을 할 수 있고 입력 에너지의 제어성이 좋아서 미세한 용접이 가능하게 하고, 빔폭 대비 용입깊이가 커서 깊은 용접 비드가 형성되며, 자동화가 용이하다는 장점이 있다. 특히 Nd;YAG 레이저의 경우는 광 섬유를 이용하므로서 에너 지의 시간 분할 및 에너지 분할을 할 수 있는 등 분기 및 배치가 용이하며 펄스의 활 용을 극대화 할 수 있는 장점이 있다. 그러나, 결점으로도 맞대기 용접의 경우 갭의 여유가 판두께, 초점위치, 빔모드에 따라 변화하는데 이는 빔 스폿이 작음에 따른 장점이 단점으로 작용하는 경우이다. 레이저 용접부의 비드 폭이 좁기 때문에 인장 강도가 모재의 인장강도보다 밑도는 것도 겹쳐서 용접된 이음 부분의 인장강도에 있 어서 단점이 되고 있다.

• Proceedings of the KWS Conference
• /
• 1995.04a
• /
• pp.58-61
• /
• 1995

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.4
• /
• pp.517-523
• /
• 2009

Magnesium alloys have many advantages such as a low density, high strength/weight ratio and well recycle. And joining process is absolutely necessary to expand the field of application of magnesium alloy. The main problems of conventional process such as arc welding for magnesium alloy are the inflammability, a tendency toward crack formation and the appearance of porosity during solidification. Laser welding technology is a promising means for overcoming these difficulties. This study is related to the laser weldability of AZ31 magnesium alloy, an all-purpose wrought alloy with good strength and ductility. The effect of welding conditions on the weldability of butt joints was examined. Also, the mechanical properties of butt welded joints were investigated by tensile test and hardness test.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2004.10a
• /
• pp.78-81
• /
• 2004

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.139-143
• /
• 2000

Laser beam weldability of Zircaloy-4 was investigated using a pulsed Nd:YAG laser of 550W average power. Mechanical properties and microstructure of laser butt welded Zircaloy-4 test specimens were examined. The influence of laser generated during laser welding was analyzed and optimum laser welding parameters were investigated.