• Horticultural Science & Technology
• /
• v.31 no.1
• /
• pp.50-55
• /
• 2013

The objective of this research was to investigate the impact of Ca fertilizer on the growth of mother plants, physiological disorders, and occurrence of daughter plants in propagation of 'Seolhyang' strawberry through plastic bag cultivation. To achieve this, chemicals of 1.125 mM $Ca(OH)_2$, 0.375 mM $MgCl_2$, 1.250 mM KCl were blended and designated to combined fertilizer (CF). Then, the effect was compared to the treatment of no Ca application (control) and a commercial fertilizer, CalMag (13-0-1.9-16-6:N-$P_2O_5$-$K_2O$-CaO-MgO), when those were applied every two weeks with controlled electrical conductivity (EC) of solution such as 0.6 or 1.0 $dS{\cdot}m^{-1}$. The number of plants showing Ca deficiency symptoms was the highest in control treatment, but those decreased significantly in CF or CalMag treatments. The differences between CF and CalMag in appearance of Ca deficient plants were not significant when two fertilizers were applied with same EC. The fresh and dry weights of mother plants were the greater in the treatments of CF or CalMag than those of control treatment. The treatments of 1.0 $dS{\cdot}m^{-1}$ of CF or CalMag were more effective than those of 0.6 $dS{\cdot}m^{-1}$ on the fresh and dry weight of the mother plants. The runner lengths in the treatment of 1.0 $dS{\cdot}m^{-1}$ of CF were the longest among the all treatments tested. The treatments of 1.0 $dS{\cdot}m^{-1}$ were more effective than those of 0.6 $dS{\cdot}m^{-1}$ of CF or CalMag in lengths and fresh and dry weight of runners. The fresh and dry weights of daughter plants were heavier in the treatments of CF than those of CalMag. Based on the above results, we concluded that the Ca deficiency in raising 'Seolhyang' strawberry can be lessened by the application of Ca containing fertilizers, but combined application of Ca, K and Mg was more effective than that of Ca alone for seedling production.

• Horticultural Science & Technology
• /
• v.17 no.2
• /
• pp.111-114
• /
• 1999

Experiments were conducted to select the optimum cultivars which are adaptable to South Korea through estimating the differences in daughter plant production and growth response among seven strawberry cultivars. In the vegetative stage, Nyoho, Akihime and Suhong produced more daughter plants than other cultivars whereas Akaneko and Tochinomine, which developed less runners, showed better condition in runner vigorness. The quality of daughter plants derived from forcing cultivars was uniform in general. Even though there was no significant differences in rooting among cultivars, runners from Akaneko and Tochinomine developed more roots and fresh weight of roots than other cultivars. In the forcing cultivars, Akihime showed the most excellent plant vigorness, yield and highest sugar content of fruits and also was 5 days faster than Nyoho in flowering date. However, the fruit tended to be softened. In the semi-forcing cultivars, Tochinomine was excellent in vigorness, firmness, sugar content of fruits and the average of fruit weight but low in flower numbers per cluster and late in the emergency of second flower cluster. Although Akaneko showed highest in sugar/acid ratio and rich in flavour, lighting treatment was recommended to this cultivar for early harvest because of softness of fruits.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.12
• /
• pp.5709-5715
• /
• 2012

Injection molding product is commonly used for reducing the weight of automotive vehicle, and door regulator guide rail with plastic material is also made by injection molding process. In order to improve the injection molding performance of plastic regulator guide rail, optimal molding condition is suggested by numerical simulation and DOE after obtaining the sensitivity of parameters for regulator rail manufacturing on warpage and fill time. Furthermore, multi direct gate method and optimal cooling circuit are introduced to get the uniform temperature distribution and better cooling efficiency in molding product. The effect of the proposed design on the injection molding performance is verified by the test of prototype of plastic regulator guide rail.

• Horticultural Science & Technology
• /
• v.30 no.6
• /
• pp.657-663
• /
• 2012

The Ca deficiency is a serious problem in the propagation of domestically bred 'Seolhyang' strawberry through soil cultivation. The objective of this research was to investigate the impact of the Ca containing fertilizers on the decrease of Ca deficiency symptoms and in the growth of mother and daughter plants. To achieve this, chemicals of 1.125 mM $Ca(OH)_2$, 0.375 mM $MgCl_2$, and 1.25 mM KCl were blended to contain the K:Ca:Mg (4:2:1) and the influence was compared to a commercial fertilizer, Azuro-Calma ($NO_3$-N 13%, $K_2O$ 1%, CaO 16%, MgO 6%), when those were applied as solutions with the electrical conductivity (EC) controlled to 0.6 or 1.0dS ${\cdot}m^{-1}$. During 120 days after transplant, the Azuro-Calma was more effective than the combined fertilizer in the reduction of mother and daughter plants on which Ca deficiency was appeared. The application of two Ca containing fertilizers resulted in the heavier fresh and dry weights of mother plants. The treatments of 1.0dS ${\cdot}m^{-1}$ of two fertilizers were more effective than those of 0.6dS ${\cdot}m^{-1}$. The combined fertilizer was also more effective than Azuro-calma on the growth of above ground plant tissue. The results in length, fresh and dry weight of runners occurred from a mother plants showed that the treatment of 1.0dS ${\cdot}m^{-1}$ of combined fertilizer was most effective followed by those of 1.0dS ${\cdot}m^{-1}$ of Azuro-Calma, 0.6dS ${\cdot}m^{-1}$ of combined fertilizer, 0.6dS ${\cdot}m^{-1}$ of Azuro-Calma, and control. The fresh weights of daughter plants were heavier in the treatments of Ca application than those in the control treatment, but the differences between 0.6dS ${\cdot}m^{-1}$ and control were not significant. The above results indicate that Azuro-Calma is more effective in decreasing plants showing the Ca deficiency symptoms. However, the combined fertilizer of K:Ca:Mg is more desirable when we are concerned about the decrease of crops showing Ca deficiency as well as increase of the growth in above ground plant tissue.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.394-394
• /
• 2009

Owing to the increasing number of intelligent homes(or called Smart home), the corresponding cost is much higher. Low voltage circuit breakers are widely used in the intelligent homes to interrupt fault current rapidly and to assure the reliability of the power supply. The distribution of magnetic field induced by arc current in the contact system of molded case circuit breaker(hereafter MCCB) depends on the shape, arrangement, and kinds of material of arc runner. This paper is focused on understanding the interrupting capability, more specifically of the arc runner, based on the shape of the contact system in the current MCCB. The magnetic driving force was calculated by using the flux densities induced by the arc current, which are obtained by three-dimensional finite element method. There is a need to assure that the optimum design required to analyze the electromagnetic forces of the contact system generated by current and the flux density be present. This is paper present our computational analysis on contact system in MCCB.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1451_1452
• /
• 2009

Owing to the increasing number of intelligent homes(or called Smart home), the corresponding cost is much higher. Low voltage circuit breakers are widely used in the intelligent homes to interrupt fault current rapidly and to assure the reliability of the power supply. The distribution of magnetic field induced by arc current in the contact system of molded case circuit breaker depends on the shape, arrangement, and kinds of material of grids. This paper is focused on understanding the interrupting capability, more specifically of the grid and the arc runner, based on the shape of the contact system in the current MCCB. The magnetic driving force was calculated by using the flux densities induced by the arc current, which are obtained by three-dimensional finite element method. There is a need to assure that the optimum design required to analyze the electromagnetic forces of the contact system generated by current and the flux density be present. This is paper present our computational analysis on contact system in MCCB.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.115-122
• /
• 2014

Injection pressure is one of factors that influence part quality. In this paper, injection pressure was minimized by optimizing valve gate locations. In order to perform design optimization, MAPS-3DTM (Mold Analysis and Plastic Solution-3D) was used for injection mold analysis and PIAnOTM (Process Integration, Automation and Optimization) was used as process integration and design optimization. Also we adapted meta models based on design of experiments for efficiency. By using introduced methodology, we were able to obtain a result so that maximum injection pressure reduced by 28% compared to the initial design. And the validity of the proposed method could also be demonstrated.

• Polymer(Korea)
• /
• v.28 no.3
• /
• pp.263-272
• /
• 2004

Using computer simulation, the processibility and properties of the inst겨ment panel of automobile produced by gas injection molding were predicted and evaluated. The P-V-T data of ABS, resin were used in the gas injection molding process in order to estimate the mold filling phenomena. The optimum process conditions were found by adjusting the process parameters including pressure, filling time, the positions of gas channel and runner. The process was simplified and the final instrument panel produced by the gas injection molding was found to have improved dimension stability compared to the one produced by conventional injection molding.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.86-92
• /
• 2021

Usually, the die-cast components used in small mobile devices require finishing processes, such as computer numerically controlled coating. In such cases, porosity is the most important defect. The shape of the molten aluminum that passes through the runner and gate in a mold is the one of the factors that influences gas porosity. To define the spurt index, which numerically indicates the shape of molten aluminum after the gate, Reynolds number and Ohnesorge number are used. Before die fabrication, computer-aided engineering analysis is performed to optimize the filling pattern. Finally, X-ray and surface inspection are performed after casting and machining to evaluate how the spurt index affects porosity and other product parameters. Based on the results obtained herein, a new gating system design process is suggested.

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.501-508
• /
• 2008

Small injection molded articles such as lens and mobile product parts are usually molded in multi-cavity mold. The problem occurring in multi-cavity molding is flow unbalance among the cavities. The flow unbalance affects the dimensions and physical properties of molded articles. First of all, the origin of flow unbalance is geometrical unbalance of the delivery system. However, even the geometry of the delivery system is well balanced, cavity unbalance occurs. This comes from the temperature distributions in the cross-section of runner. Temperature distribution depends upon injection speed because heat generation near runner wall is high at high injection speed. Among the operational conditions, injection speed is the most significant process variable affecting the filling unbalances in multi-cavity injection molding. In this study, experimental study of flow unbalance has been conducted for various injection speeds and materials. Also, the filling unbalances were compared with CAE results. The dimensions and weights of multi-cavity molded parts were examined. The results showed that the filling unbalances vary according to the injection speeds and resins. Subsequently, the unbalanced filling and pressure distribution in the multi-cavity affect the dimensions and physical states of molded parts.