• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.92-99
• /
• 2011

To measure the traffic pollutants with high temporal and spatial resolution under real conditions, a mobile emission laboratory (MEL) was designed. The equipment of the mini-van provides gas phase measurements of CO, NOx, $CO_2$, THC (Total hydrocarbon) and number density & size distribution measurements of fine and ultra-fine particles by a fast mobility particle sizer (FMPS) and a condensation particle counter (CPC). The inlet sampling port above the bumper enables the chasing of different type of vehicles. This paper introduces the technical details of the MEL and presents data from the car chasing experiment of diesel bus equipped with aftertreatment system. The dilution ratio was calculated by the ratio of ambient NOx and tail-pipe NOx. Most particles from the diesel bus were counted under 300 nm and the peak concentration of the particles was located between 30 and 60 nm. The total PM number emission from diesel bus equipped with DPF was 10 orders of magnitude lower compared to those emitted from base diesel bus. And the total PM number emission from diesel bus equipped with SCR was comparable to the particle emission from base diesel bus.

• 대한기계학회논문집B
• /
• 제31권2호
• /
• pp.188-194
• /
• 2007

New diesel engines equipped with common-rail injection systems and advanced engine management control allow drastic decreases in the production of particulate matters and nitrogen oxides with a significant advantage in terms of the fuel consumption and $CO_2$ emissions. Nevertheless, the contribution of exhaust gas after treatment in the ultra low emission vehicles conception has become unavoidable today. Recently the passive type DPF(Diesel Particulate Filter Trap) system for diesel passenger vehicle has been manufactured into mass production from a French automotive maker since the year of 2000. This passive DPF system fully relies on the catalytic effects from additives blended into the diesel fuel and additives injected into the DPF system. In this study, the effects of PM regeneration in the commercial diesel passenger vehicle with the passive type DPF system were investigated in chassis dynamometer CVS(constant volume sampler)-75 mode. As shown in this experimental results, the DPF regeneration was observed at temperature as low as $350^{\circ}C$. And the engine-controlled the DPF regeneration founded to be one of the most promising regeneration technologies. Moreover, the durability of this DPF system was evaluated with a season weather in terms of the differential pressure and exhaust gas temperature traces from a road test during the total mileage of 80,000km.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.144-151
• /
• 2016

This study effect of engine oils on regulated fuel economy and emissions including particulate matter (PM) to provide basic data for management of engine oil in vehicles. Three engine oils (Group III base oil, Group III genuine oil with additive package and synthetic oil with poly alpha olefins (PAOs)) were used in one gasoline, one LPG(liquefied petroleum gas) and two diesel vehicles. In the case of diesel vehicles, one is a diesel vehicle without DPF (diesel particulate filter) other is a diesel vehicle with DPF. In this study, the US EPA emission test cycle FTP-75, representing city driving, was used. HORIBA, PIERBURG, and AVL gas analyzers were used to measure the fuel economy and regulated emissions such as CO, NOx, and THC. The number of PM was measured using a PPS (pegasor particle sensor). And, the shape of PMs was analyzed by SEM (scanning electron microscope). The effects of oil type on fuel economy, exhaust gas, and PM were not significant because engine oil consumption by evaporation and combustion in the cylinder is very tiny. Fuel and vehicle type were dominant factors in fuel economy and emissions. HC emission from gasoline vehicles was higher than that from other vehicles and NOx emission from diesel vehicles was higher than that from other vehicles. The number of PM was not affected by the engine oil, but by the driving pattern and fuel. The shapes of the PM, sampled from each vehicle using any test engine oil, were similar.

• 해양환경안전학회지
• /
• 제23권5호
• /
• pp.549-557
• /
• 2017

본 연구에서는 강화되는 황산화물 및 입자상물질의 배출규제를 만족시키기 위한 후처리장치인 스크러버(scrubber)에 대한 수치해석적 연구를 수행하였다. 먼저 수치 해석을 통하여 기존 스크러버의 문제점을 파악하고, 이러한 문제점들을 개선할 수 있는 새로운 형태의 와류형 스크러버를 설계하여 분석하였다. 그 결과 와류형 스크러버에서 배기가스는 하부에서 와류를 형성하고 그 중 일부는 바닥면을 통과하여 가이드 베인을 따라 배출되는데, 이 때 수직 방향의 압력구배는 크지 않으나 배플의 내 외부에는 압력차가 발생하는 것으로 나타났다. 배기가스 유선의 형태를 확인한 결과, 물이 분사되지 않는 경우에는 물이 분사되는 경우에 비해 가이드 베인을 따라 출구까지 일정하게 유동하였으며, 유동의 형태에 가이드 베인과 노즐의 배열 및 수압 등이 영향을 미치는 것으로 확인되었다. 와류형 스크러버의 경우 입 출구의 차압이 기존의 스크러버 대비 절반 이하로서 기관의 배압에 미치는 영향이 훨씬 적은 것으로 나타났다.

• 대한기계학회논문집B
• /
• 제35권5호
• /
• pp.525-531
• /
• 2011

디젤엔진에서 배기가스 재순환(EGR; Exhaust Gas Recirculation)은 선택적 환원 촉매나 $NO_x$ 흡장 촉 매에 비해 $NO_x$ 배출 저감을 위한 가장 효과적인 기술이다. 점점 더 강화되어 가는 $NO_x$ 배출 규제를 만족시키기 위해서는 많은 양의 EGR 가스 공급이 필요하다. 저압 EGR은 일정한 과급 압력에서 가변형상 터보차져의 제어와 거의 독립적이기 때문에 EGR 공급 측면에서 보면 저압 EGR이 기존의 고압 EGR에 비해서 더 많은 장점을 갖는다. 본 연구에서는 저압 EGR이 연소 특성에 미치는 영향을 고압 EGR을 적용했을 때와 비교하였다. 각 EGR 루프에 대해 혼합기의 희석 정도에 따른 영향을 분석하기 위해 독립변수로써 희석비를 사용하였다. 저압 EGR을 적용하였을 때, 고압 EGR을 적용했을 때와 동등한 $NO_x$ 배출량을 유지하면서 연료 소비율과 매연 배출은 고압 EGR의 경우보다 좀 더 낮은 결과를 보였다.

• 해양환경안전학회지
• /
• 제28권6호
• /
• pp.1092-1099
• /
• 2022

대기오염물질과 온실가스 배출량을 저감 시키기 위한 배기 후처리 장치에 대한 연구는 활발히 진행 중이지만 그 중 선박용 입자상물질/질소산화물(PM/NOx) 동시저감 장치에서는 엔진에 미치는 배압 및 필터 담체 교체에 대한 문제가 발생하고 있다. 본 연구에서는 PM/NOx를 동시저감 할 수 있는 일체형 장치의 최적 설계를 위해 장치 내부 유동과 입·출구 압력을 통한 배압의 변화를 연구하여 적절한 기준을 제시하였다. Ansys Fluent를 활용하여 디젤미립자필터(DPF) 및 선택적촉매환원법(SCR)에 다공성 매체 조건을 적용하였고 공극률은 30 %, 40 %, 50 %, 60 % 및 70 %로 설정하였다. 또한, 엔진 부하에 따른 Inlet 속도를 경계 조건으로 7.4 m/s, 10.3 m/s, 13.1 m/s 및 26.2 m/s로 적용하여 배압에 미치는 영향을 분석하였다. CFD 분석 결과, 장치의 입구 온도 보다 입구 속도에 따른 배압의 변화율이 크고 최대 변화율은 27.4 mbar였다. 그리고 모든 경계 조건에서의 배압이 선급 기준인 68 mbar를 초과하지 않았기 때문에 1800 kW 선박에 적합한 장치로 평가되었다.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.7-12
• /
• 2012

Cooled EGR system is widely used to reduce NOx emissions in diesel engine. But when EGR rate was increased, combustion stability was worsened and PM level was increased. So determining optimized control point of EGR rate is important. In order to determine this point, it is important to figure out the effect of EGR system on the exhaust emissions. In this research, NOx and PM emissions were analyzed with various coolant temperature supplied to the EGR cooler at several positions such as downstream of turbocharger, upstream and downstream of DPF. Effects of some variables such as EGR rate, hot / cooled EGR and change of injection timing were estimated. And $CO_2$ emissions were measured at exhaust and intake manifold to calculate EGR rate at each engine operating condition. Also combustion analysis was performed in each engine operating conditions. In the result of this study, there was trade-off between NOx emissions and PM emissions. When EGR rate was increased, combustion pressure was decreased and COV of IMEP was increased.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.88-97
• /
• 2012

To measure the traffic pollutants with high temporal and spatial resolution under real conditions, a mobile emission laboratory (MEL) was designed. The equipment of the mini-van provides gas phase measurements of CO, NOx, CO2 and THC (Total hydrocarbon), and number density & size distribution measurements of fine and ultra-fine particles by a fast mobility particle sizer (FMPS) and a condensation particle counter (CPC). The inlet sampling port above the bumper enables the chasing of different type of vehicles. This paper introduces the technical details of the MEL and presents data from the experiment in which a MEL chases a city bus fuelled by diesel, DME and Bio-diesel. The dilution ratio was calculated by the ratio of ambient NOx and tail-pipe NOx. Most particles from the bus fuelled by diesel were counted under 300 nm and the peak concentration of the particles was located between 30 and 60 nm. However, most particles in the exhaust of the bus fuelled by DME were nano-particles (diameter: less than 50 nm). The bus fuelled by Bio-diesel shows less particle emissions compare to diesel bus due to the presence of the oxygen in the fuel.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권4호
• /
• pp.379-387
• /
• 2011

최근 디젤엔진에서 엔진성능향상 및 배출가스저감을 위해 저압 EGR시스템에 대하여 연구개발이 활발히 진행되고 있다. 저압 EGR시스템은 EGR율에 따라 과급압력이 영향을 받지 않기 때문에 PM을 최소 화하면서 $NO_x$를 저감할 수 있는 장점을 갖고 있다. 본 연구에서는 2.0L급 고속직분사방식의 엔진에서 출력 및 연비저하로 EGR적용이 어려운 엔진회전수 2000 rpm, BMEP 1.0 MPa, 과급압력 181.3 kPa인 중부하 운전영역에서 서로 다른 EGR시스템에 따른 엔진성능 및 배출가스 특성을 실험적으로 연구하였다. 그 결과로서 기존의 고압 EGR시스템 또는 배압조절밸브를 사용하는 저압 EGR시스템에 비하여 ETC를 적용한 저압 EGR시스템이 $NO_x$ 배출특성은 큰 차이가 없는 반면에, 연비 및 열효율이 향상되고 PM 저감에 연소효과를 나타내고 있음을 확인하였다.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.