• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.179-182
• /
• 2012

Effect of double post injections on diesel PCCI combustion with focus on HC emission was investigated in a single-cylinder direct-injection diesel engine. The ISFC, HC and CO emissions were reduced by single or double post injections. The application of double post injections could also improve the trade-off relationship between NOx and HC emissions under wide EGR rate range.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.195-198
• /
• 2012

Numerical simulation is performed to evaluate the conditional moment closure (CMC) models for spray development, ignition, and turbulent combustion for the Engine Combustion Network (ECN) test cases. The CMC model is implemented in the open source code, OpenFOAM, to provide conditional flame structures through the solution of Eulerian as well as Lagrangian conditional transport equations. In spite of more accurate treatment of the convective term, Eulerian CMC provides similar ignition delays and lift-off lengths with Lagrangian CMC.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.309-310
• /
• 2012

Modeling of biodiesel combustion on compression ignition engine was conducted by using the KIVA3v-Release 2 code coupled with Chemkin chemistry solver2. In order to calculate the chemical kinetics of combustion of biodiesel, a reduced mechanism of methyl decanoate and methyl 9-decanoate was used. It is composed of 123 species and 394 reactions. Also, the experiments were performed on a single-cylinder engine. The simulation results agreed well with experiments results. And soot concentrations of biodiesel were lower than those of diesel.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.29 no.1
• /
• pp.30-38
• /
• 1993

In this study, the combustion characteristics in a pre-combustion chamber diesel engine was investigated with experimental conditions of marine engine load. The heat release analysis used was a single-zone single-chamber thermodynamic analysis based on pre-combustion chamber pressure-time data. Based on the results of this investigation, the following conclusions were reached: 1) Increasing the load, peak pressure was increased and position of P sub(max) was retarded in crank angle degrees. 2) Ignition delay time was almost constant without relating to the load and the heat values to form a combusitible mixture were decreased apparently with increasing the load. 3) In premixed-combustion mode, the pattern of heat release rate was resembled without relating to the load and premixed-combustion time was shortened with increasing the load. 4) Increasing the load, mass of premixed-burned fuel was increased slightly, but was invariable beyond a certain fuel-air ratio. 5) Increasing the load, premixed-burned fraction was decreased.

• Clean Technology
• /
• v.14 no.2
• /
• pp.144-151
• /
• 2008

Life cycle assessment was carried out to evaluate the environmental values of dimethylas a diesel alternative fuel with the assumption of dimethyl ether production from natural gas via synthesis gas. The whole life cycles from raw material acquisitions to the final usages of diesel and dimethyl ether were involved in the assessment. Inventory analysis showed that the most significant environmental impacts came from resource depletions and air emissions. Impact assessment revealed that dimethyl ether was environmentally better in the aspect of human health and ecosystem quality but worse in resource depletions compared with diesel fuel. Suggestions for environmental improvement of dimethyl ether as a diesel alternative fuel were prepared based on the assessment results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1359-1365
• /
• 2011

The purpose of this study is to investigate the effect of ethanol content on the emission of nanosized particles from a diesel-ethanol blended fuel engine. The engine combustion and exhaust emission characteristics of a singlecylinder diesel engine were analyzed using an emission analyzer and an SMPS(scanning mobility particle sizer). The analysis revealed that soot emission increased with the ignition delay. When the ignition delay was fixed, an increase in the ethanol content caused a decrease in the soot emission. With an increase in the ethanol blending ratio, the number concentration and mass distribution of nanosized particles generally decreased. However, for 30% ethanol blending, large particles were observed because of the agglomeration of soot particles, and consequently, the particle mass increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.108-115
• /
• 2014

In this study, experimental approaching method was applied under and single-cylinder engine to research the performance of direct needle-driven piezo injector (DPI) for CR direct-injection. As key-point factor of this DPI that relies on direct-acting operating of injector needle, unlike conventional hydraulic-servo, its nozzle needle can be directly driven by piezo actuator. Thus, effect of direct-acting injection of DPI on diesel combustion and emission characteristics was investigated under common-rail single-cylinder direct-injection engine, equipped with three different driving mechanism, including indirect-acting solenoid, piezo and DPI system. As main results, it found that a direct-acting piezo injector has higher of IMEP. And it has higher heat release rate during premixed combustion and mixing controlled combustion phase due to its higher heat release, even though nitrogen oxide (NOx) formations were increased slightly.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.420-427
• /
• 2017

Recently, the depletion of fossil fuels, global warming and environmental pollution have emerged as a worldwide problem, and studies of new renewable energy sources have been progressed. Among the many renewable energy sources, the use of bio fuel has the potential to displace fossil fuels due to low price, easy to handle, and the abundant sources. Pyrolysis oil (PO) derived from waste wood and sawdust is considered an alternative fuel for use in diesel engines. On the other hand, PO is limited to diesel engines because of its low cetane number, high viscosity, high acidity, and low energy density. Therefore, to improve its poor properties, PO was mixed with alcohol fuels, such as ethanol. Early mixing with ethanol has the benefit of improving the storage and handling properties of the PO. Furthermore, a PO-ethanol blended fuel was injected separately, which can be fired through pilot-injected diesel in a dual-injection diesel engine. The experimental results showed that the substitution of diesel with blended fuel increases the amount of HC and CO, but reduces the NOx and PM significantly.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.674-680
• /
• 2014

Monitoring systems of informations for ship performance have become important gradually for economical management of existing ship. Monitoring of NOx emission from marine diesel engines is one of them. The measurement of NOx emission, however has been many difficulties due to technical and costly problems. A monitoring by prediction method of NOx on-board ship according to sailing condition of ship could be an useful method. In this paper, it is discussed about modified method of one-zone model which has been utilized usually for analyzing the combustion process. The modified method is able to calculate the temperature of burned region from the result by one-zone model. Influences which excess air ratio during combustion process affected for the gas temperature and NOx emission were investigated. From the results variation of excess air ratio during combustion process could be estimated inversely through the comparison with measurement of NOx emission.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3329-3334
• /
• 2007

The purpose of the research is to investigate of diesel spray combustion for simultaneously reduce way NOx and PM. The pressure diesel injection were done into intermediates that are generated by very lean DME HCCI combustion using a RCM. The concentration of intermediate could not be directly measured; we estimated it by CHEMKIN calculation. DME HCCI characteristic is surveyed. Validations of the CHEMKIN calculation were confirmed pressure rise of an experiment and pressure rise of a calculation. Using a framing streak camera captured two dimensional spontaneous luminescence images from chemical species at low temperature reaction(LTR) and high temperature reaction (HTR). Also, the combustion events were observed by high-speed direct photography, the ignition and combustion were analyzed by the combustion chamber pressure profiles.