• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.16-21
• /
• 2010

분사된 연료의 미립화(atomization), 증발(evaporation), 그리고 혼합기형성과정(mixture formation process)이 디젤엔진의 착화 및 연소특성에 영향을 미치기 때문에, 디젤엔진 내에 분사된 연료의 구조해석으로부터 일련의 과정, 즉 고압분사, 분열(breakup), 미립화, 그리고 주위기체의 난류 도입(entrainment)에 관한 연구$^{1-3)}$는 꾸준히 행해져왔다. 본 연구는 증발디젤분무의 구조해석으로부터 디젤충돌분무의 혼합기형성과정을 조사한다. 주위기체의 밀도는 실험변수로서 선택하였고, $5.0kg/m^3$에서 $12.3kg/m^3$까지 변화시켰다. 그리고 소형고속디젤엔진에 있어서 연료분사초기의 상태의 고온 고압 설정이 가능한 정적용기를 사용했다. 주위 온도와 연료분사압력은 각각 700K 및 72MPa로 일정하게 유지했다. 충동증발분무의 액상과 기상의 이미지는 엑시플렉스형광법으로 동시 계측하였다. 실험결과로서 주위기체의 밀도가 높을수록 충돌분무의 선단도 달거리가 주위기체의 항력으로 인하여 감소하였다.

• Journal of Power System Engineering
• /
• v.9 no.3
• /
• pp.21-25
• /
• 2005

디젤분무가 연소실 벽에 충돌할 때의 연료부착특성을 파악하기 위하여 평판에 충돌하는 디젤 분무의 부착특성을 실험적으로 연구하였다. 투명 아크릴판을 이용하여 연료액막과 충돌분무를 동시에 촬영하였고, 충돌분무의 성장에 따른 연료액막의 성장도 함께 측정되었다. 부착된 연료는 연료액막 및 부착액적들로 나누어서 측정할 수 있었으며 그 결과 연료액막 주변에 무수한 연료액적이 부착함을 알 수 있었다. 시간에 따른 부착연료비를 예측하기 위하여 몇 가지 가정이 사용되었다. 그 결과 시간경과에 따른 부착연료비를 충돌거리 10mm, 30mm, 50mm에 대하여 예측할 수 있었다.

• Journal of ILASS-Korea
• /
• v.8 no.4
• /
• pp.17-23
• /
• 2003

To find suitable injection pressure, ultra high pressure impinging spray characteristics were investigated with a impinging distance and a impinging angle by using high pressure injection system. As impinging distance was increased, spray penetration was decreased but spray height was increased. For increase of injection pressure, spray penetration and spray height were increased until 2,500bar. But over this injection pressure region, the rate of increase was decreased suddenly.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.60-68
• /
• 1996

디젤 엔진의 분사연료를 연소실 내부에 마련된 작은 돌출부에 충돌시켜 액적을 작게 부수고 연료가 연소실 내부에 고루 분포할 수 있도록 하여 여러 가 지 엔진성능향상을 도모한 새로운 디젤 연소실 시스템이 최근 제시되고 있다. 이들 시스템은 피스톤 내부 혹은 엔진헤드 부위에 분사연료 충돌부를 두고 있는데, 여기에서는 이 새로운 시스템 개발에 있어 고려되어야 할 몇 가지 중요 요인들에 중점을 두어 분석하였다. 결과로서 분사압력, 사노즐크기, 주위공기 온도와 압력의 변화가 분무 평균입경과 분무연료의 분포에 미치는 영향을 제시하였다.

• Journal of ILASS-Korea
• /
• v.5 no.4
• /
• pp.1-11
• /
• 2000

• Journal of ILASS-Korea
• /
• v.4 no.2
• /
• pp.40-46
• /
• 1999

Experimental investigation of unsteady impinging diesel spray on the flat plate have been carried out using high speed camera and Malvern system. The density ratios of ambient gas to diesel fuel were varied using $N_2$ and Ar gas in the case of 14.9, 21.2, 28.4, 35.1, 40.4, and 50.1. With the increase of gas density ratio, the radial penetration is decreased due to the resistance of the ambient gas. With the increase of the gas density ratio and the distance between nozzle tip and flat plate, the height of spray is increased due to the entrance and circulation. With the increase of gas density ratio, SMD is decreased on the nearby position at the center of flat plate, but SMD is increased on the far position. As the distance between nozzle tip and flat plate is increased, SMD is always decreased.

• Journal of ILASS-Korea
• /
• v.2 no.4
• /
• pp.1-6
• /
• 1997

In the case of analyzing the combustion phenomena in a small high speed DI diesel engine, one demands the experimental results of the impinging spray on the wall as a basic characteristics. In the experiments presented here, diesel fuel oil was injected into a high pressure chamber in which compressed air at room temperature was charged. The single spray was impinged on a flat wall. The growth of the spray was photographed with transmitted light or scattered light. The effect of the spray axis angle to the wall on the impinging spray was revealed. Finally, the experimental results was presented, that is, the radius and height of the impinging spray was influenced by above mentioned variable.

• Journal of ILASS-Korea
• /
• v.1 no.2
• /
• pp.24-32
• /
• 1996

Most of the research of small engines to date focused on developing spark ignition engines occupied much parts. Recently the number of a small direct injection diesel engine applied in small cars has been increased and considered as a next generation power source for passenger cars because of its high efficiency. Therefore the combustion chamber becomes smaller and the fuel injection pressure goes higher, which makes fuel sprays impinged easily on the combustion chamber walls. When strong swirls are not induced, the fuel may not mix with air because of fuel deposition on the wall. As a positive way, the combustion chamber systems which is using spray wall impaction has been introduced and assessed by an experimental or a simulate manner. In these systems the raised lands are positioned in tile chamber for spray impaction in order to break up the fuel drops into much smaller and direct them into desirable direction. This study addresses to the effects of rho position and size of the raised land or glow plug to help the chamber design using spray wall impaction. The characteristics of the spray impinged on various lands are investigated and compared with each other. Then the chamber shapes are discussed with the characteristics and their proper position and size is proposed in any chamber volume.

• Journal of ILASS-Korea
• /
• v.1 no.4
• /
• pp.24-31
• /
• 1996

This study addresses the behavior characteristics of diesel spray injected on the impinging disk with the room temperature. The models of impinging spray are the stick, the reflect and the wall jet model In the initiative of the fuel injection the impinging spray was the reflect model. because the momentum of droplets was very large. This model developed to the wall jet model according to the time approaches. On the low temperature disk the fuel film was made by the attachment of the droplets with low Weber number. The thickness of impinging spray was increased when the disk approached to the nozzle tip. Mathematical analysis for calculation with the behavior of impinging spray have to consider the reflecting effect and the influence of the fuel film.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.55-65
• /
• 1999

Many researches have been investigating small direct-injection diesel engines using the spray impacting on walls. Those systems have one or more raised pips to break-up the fuel and spread it widely toward a desired direction in a combustion chamber. In this study, the sizes and heights of the pips are determined by using a computational fluid dynamics code employing non-orthogonal grid systems. In order to find out the suitable pip-shape to a small chamber, the spray behaviors, occupied spary volumes and averaged droplets sizes are calculated with the variation of shape of the pip, such as, size and heights and inclined degree. The desired shape of the impinging land is proposed for the design of combustion system in small diesel engines.