• CDE review
• /
• v.2 no.2
• /
• pp.52-54
• /
• 1996

드럼세탁기에 있어서 weight는 세탁기의 진동 및 소음에 중요한 역할을 한다. 기존 pulsator 세탁기는 액체밸런스를 사용하여 세탁물의 편심을 상쇄시켜 세탁기의 진동을 억제시키지만, 드럼세탁기는 주물이나 시멘트 등을 weight balance로 사용하고, 세탁기 구동부의 무게, damping system 등과의 상호작용으로 세탁기의 진동을 억제시킨다. 본 연구에서는 Ideas-Design의 Master Molder와 Assembly을 사용하여 드럼세탁기의 weight balance을 설계한다. 이와 같이 weight balance는 드럼진동 및 소음 뿐만 아니라 세탁기의 전체 무게에도 매우 큰 영향을 미친다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.1
• /
• pp.45-58
• /
• 2002

In this paper, we designed the circuit of drive control for towing winch. It is composed of reference voltage circuit for driving voltage reference, low pass filter circuit for noise reduction, dead zone circuit for initial transient input, and driving circuit for drum direction/velocity control. Also it is realized a drive control circuit for towing winch drum in accordance with PWM(pulse width modulation) method to suit it's purpose of a large capacity driving system. The performance of the designed circuit is analyzed by experiments and the appliablity for driving the towing winch drum satisfactorily is evaluated through a various testing.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.219-220
• /
• 2015

본 논문에서는 높은 성능의 속도 제어 특성을 만족하기 위해 위치 기반의 반복제어기를 이용한 속도 제어기를 설계 하여, 레이저 프린터의 OPC 드럼의 속도제어에 적용 하였다. 레이저 프린터 OPC 드럼의 외란은 드럼의 위치에 종속적으로 나타난다. 따라서 위치 기반 반복제어기는 기존의 반복제어기 보다 기준 속도 변동에 강인하며, 레이저 프린터의 다양한 인쇄 속도에 적용 가능하다. 실험 결과, 위치기반 반복 제어기가 기존의 반복제어기 보다 기준 속도 변동에 강인하며 다양한 인쇄 속도에서도 적용 가능함을 보여주었다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.491-499
• /
• 2007

The variation of a load characteristic in the motor drive is one of the most important consideration. Because the current flowing into the motor generally varies according to the load variation, it needs to design the motor drive circuit properly in accordance with the load variation. However, the load variation of the drum washing machine is irregular and large due to the water flow and reverse load torque. Therefore, to design the motor drive circuit considering this load pattern, simulation results shows the load pattern modeling of the drum washing machine based on the physical analysis in this paper.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.138-139
• /
• 2010

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.2
• /
• pp.150-159
• /
• 2009

Generally, the operating efficiency of the washing machine is mostly affected by the washing time. The washing time is determined by the amount and the type of the laundry. Although the type of the laundry is easily inputted by the user, but the amount of the laundry is difficult to do. For this reason, the specific process is existed for the estimation of the laundry and the time of the washing mode is determined by the estimated laundry. Therefore, this paper proposes the washing load estimation algorithm by the inertia estimator. The proposed algorithm is implemented on the PMSM drive using the low cost position sensor for practical washing machine application. The proposed algorithm is verified by the drum washing machine for the practical load condition test.

• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.373-385
• /
• 2022

The drum cutter, which is used in the form of an attachment of a excavator, is very useful in that it can be used in connection with a excavator that can perform various tasks in the field. This study estimated the load and torque acting on the drum cutter attachment by measuring the hydraulic pressure and strain that appear during excavation on the exposed rock slope using the drum cutter installed in the excavator. Working conditions such as the operation angle between the boom and arm of the excavator were divided into eight working modes. And as a result of analyzing the variations in hydraulic pressure and action force according to the working mode, it was confirmed that the hydraulic pressure and flow rate can be driven without any problems within the range considered in the manufacturing specifications of the drum cutter. The average load and torque acting on the drum cutter were within the range of the manufacturing specifications, but the maximum load was up to four times the specification. Because sumping was not properly performed due to the high ground strength and the ground included discontinuous surfaces in some locations, no trend of load and torque was found depending on the angle between the boom and arm of the excavator. However, it is believed that this result can be used to determine the range of loads and torques that appear on the drum cutter when excavating a high-intensity rock.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.151-151
• /
• 2003

최근 휴대폰용 LCD, 컴퓨터용 TFT LCD, 가정용 PDP 등 평판 디스플레이 산업의 발달에 힘입어 평판 디스플레이 장치의 구동 칩 실장 부품인 TCP(tape carrier package), COF(chip on film) 제조 산업 또한 발전하고 있다. 이들 TCP, COF는 디스플레이 장치의 경박화에 따라 보다 가는 선폭의 회로가 요구되어지는데 이를 위해 회로를 구성하는 기본소재로 얇은 두께의 동박이 사용된다. 회로기판용 동박으로는 압연동박과 전해동박이 함께 사용되어 왔으나 박막의 제조가 어려운 압연동박의 단점과 면에 수직한 주상정 조직이 발달해 있어 일반 압연 동박에 비해 접착력이 뛰어나며 전류밀도 또는 티타늄 음극 드럼 회전 속도를 조절하여 두게 조절이 용이한 전해동박의 장점으로 인해 현재 압연동박의 전해동박으로의 대체가 증가하고 있다. 전해동박의 제조공정은 크게 제박 공정과 후처리 공정으로 나눌 수 있다. 전해동박은 먼저 드럼형태의 티타늄 음극과 불용성 납 양극으로 이루어진 제박기에 고 전류를 가하여 황산구리 용액 중 구리를 티타늄 음극에 석출시킴으로서 구리 원박을 제조한 후 접착력 향상을 위한 노듈 형성, 방식, 방청, 내열성 향상 등을 위한 여러 개의 단위 셀 조합으로 이루어진 후처리 공정을 거쳐 제조된다.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.68-70
• /
• 2008

레이저 빔 프린터의 인쇄 품질은 화상 인쇄 과정에 직접적으로 관계되는 OPC 드럼(Organic Photoconductive Drum) 및 PTB(Paper Transfer Belt)의 운전 속도 특성과 관계 있는 것으로 알려져 있다. 그러나 그 관계가 정량적으로 연구된 바는 없었다. 본 논문에서는 인쇄 동작중인 OPC 드럼 및 PTB의 실제 속도를 측정하고, 속도 측정 결과에 나타나는 특성이 실제 인쇄 결과에 미치는 영향을 정량적으로 분석한다. 또한 위의 속도 측정 및 분석 결과를 바탕으로 하여 레이저 빔 프린터의 인쇄 품질을 향상시킬 수 있는 방법을 제안하고, 실험을 통해 그 타당성을 검토한다. 제안 된 방법에의해 인쇄 품질의 정도(Accuracy)가 5배이상 개선됨을 확인하였다.

• Journal of Korean Society of Forest Science
• /
• v.97 no.1
• /
• pp.61-70
• /
• 2008

This study was conducted to develop a mobile tower-yarder with tractor for agriculture and forestry that is the efficient yarder in steep terrains, thinning operation and small scale logging operation. It was designed and manufactured that the power source of tower-yarder is equiped three hydraulic pump connected to PTO of tractor, and three hydraulic pump is used to operate the four motor for drum, the cylinder for clutch of interlocker, the cylinder for tower expanding and the out-rigger cylinder. It was to adopt the running skyline system and the inter-lock function, and to equip the double capstan drum, the storage drum and the clutch for interlock in the development of tower-yarder. It was to develop the tower-yarder which the winch torque of double-capstan drum, the traction force of double-capstan drum, the number of rotation of double-capstan drum and the line speed is $191kg{\cdot}m$, 1,910 kgf, 220.5 rpm and 138.5 m/min, respectively. And it was known that the optimum flange diameter of the main and haulback storage drum is about 360 mm and about 460 mm in order to storage the main line length of 250m and the haulback line length of 450 m. The carriage was made to adopt the running skyline system and to equip the lock function in order to the convenience of chocking and the fall down preventing of tree. It was provided to develop the wire remote controller for the inter-lock function, the convenience of control and the efficiency of yarding. In development process, this tower-yarder was attached the 3-point linkage hitch equipment and the tire wheel for the traction and moving of tower-yarder. Also, it was equipped that the out-rigger and the guy line in order to raise the safety and efficiency of yarding of tower-yarder.