• Magazine of the Korea Concrete Institute
• /
• v.9 no.6
• /
• pp.185-193
• /
• 1997

본 연구는 각종 제진재료를 이용하여 진동을 억제할 수 있는 콘크리트를 개발하여 각종 건설공사에서 흔히 발생할 수 있는 진동공해문제를 억제하고자 하며 아울러 폐기물의 재활용차원에서 폐자재를 이용하여 유용한 제진콘크리트를 개발하고자 하는데 그 목적이 있다. 우선, 제진재료를 이용한 압축강도 (200kg/$\textrm{cm}^2$)이상의 콘크리트 배합비를 찾기 위하여 24배치의 예비실험을 수행하였으며, 선정된 적정배합비에 따른 제진재료를 이용한9개의 진동시험체보를 제작하여 보의 구조적 및 재료적 동적특성 즉 1차 공명진동수와 동적 휨강성 및 감쇠비를 측정하여 제진효과를 조사하였다. 그리고 압축강도에 의한 각 시험체의 균열모멘트를 추정하여 재하하중과 균열모멘트비(M/Mcr)에 따른 하중단계별 동적특성값을 살펴보았다. 제진재료로서는 라텍스(Latex), 고무분말(Rubber Powder)그리고 플라스틱 레진( Plastic Resin)등을 사용하였고, 재료적, 구조적 진동감쇠효과를 파악하고자 KS F2437규정과 진동파의 속도법을 사용하였으며, 감쇠비 측정은 Frequency Spectrum 곡선에 대한 Polynomial Curvefitting 방법과 기하학적 해석방법을 이용하여 각각의 결과를 비교.분석하였다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.1
• /
• pp.29-34
• /
• 2010

The main objective of this research is to present the behaviors of precast concrete slab under moving wheel loads. The simulated moving wheel tester and precast concrete slab were designed for this research. In particular, a comparative analysis between the structural analysis and the moving wheel load test was evaluated in connection parts, deformation, bedding layer of concrete slab panels. In the comparisons of the test results from static and moving wheel loads, the maximum deformations were similar. It should be noted that the deformation of panel 2 from the static loading test was larger than that of other panels, while the deformations of panels 1 and 3 were more noticeable than that of panel 2.

• International Journal of Highway Engineering
• /
• v.8 no.1 s.27
• /
• pp.77-87
• /
• 2006

Dynamic stability (DS) in the wheel tracking (WT) test is used as a basic index of rut-resistance for asphalt mixtures. In general, the deeper rut depth is obtained from the weaker mixture, resulting in the lower DS value. On the other hand, the shallower rut depth is obtained from the stronger mixture, resulting in the higher DS. However, it is not always the case when the DS is calculated by the existing method because the DS is simply determined based on the slope at the final stage of the rut depth-cycle curve. Specifically, in the case of the depth-cycle curve showing a steeper slope in the early part but flatter slope in last part, the DS is calculated to be higher than the curve showing a ever-increasing slope throughout the test. As long as the last part of slope is flatter, the deeper final rut depth is evaluated to show a higher DS than the little final rut depth. Therefore, a reasonable method for DS evaluation need to be established. Several new methods were suggested by considering the early, middle and final parts of rut depth to determine a reasonable DS. The results have shown that those new methods have demonstrated a significant improvement in distinguishing similarly performing mixtures. The result also showed that $DS_2$ had better correlation with SD than any other methods , representing the rutting resistance of asphalt mixture very well. The new DS calculation method is relatively simple and easy to follow. More validatin study is required for practical application.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.5
• /
• pp.97-105
• /
• 2001

현장타설말뚝의 건전도 평가에서 충격반향, 충격응답기법과 같은 비검측공 시험법을 적용하는 사례가 점차로 증가되는 추세에 있다. 비검측공시험법의 적용성을 체계적으로 평가하기 위해 수행된 일련의 연구결과 중에서 본 논문에서는 시험법의 결함탐지 능력을 평가하기 위해 수행된 해석적 연구결과에 관해 논한다. 이 연구에서는 시험법의 결함탐지능력에 대한 제반 영향인자 중에서 결함의 유형, 위치 및 크기의 영향을 평가하고자 하였다. 이를 위해서 여러 가지 조건에서 말뚝머리에 작용하는 충격하중에 대한 흙-말뚝 구조의 동적응답을 ABAQUS를 이용한 유한요소법으로 해석하였다. 이로부터 얻은 신호를 충격반향 혹은 충격응답기법으로 처리.분석하여 각 시험법의 결함탐지 능력을 평가해 보았다. 연구결과 이들 두 기법 모두 결함의 위치와 유형은 비교적 정확하게 탐지하는 것으로 나타났다. 그러나 충격응답기법을 이용하여 추정한 결함 크기는 신뢰도가 매우 낮았다. 이 문제를 해소하여 시험법의 적용성을 향상시키기 위해서는 측정된 동적응답신호를 이용하여 적절한 역계산 기법을 개발하여 적용할 필요가 있다는 결론을 얻었다.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.12
• /
• pp.5-11
• /
• 2023

Economic damage is occurring due to landslides and debris flows that occur when the ground artificially created for roads or photovoltaic power generation facilities is weakened by rainfall such as torrential rain. In order to understand the stability of the artificially created ground, it is very important to check the ground information such as the compositional state and mechanical characteristics of the stratum. However, since most of the investigation sites are steep slopes or there are no access roads, it is not easy to enter the drilling equipment commonly used to check ground information and perform standard penetration tests. In this study, a dynamic cone penetration test (DCP) device using a miniaturized auger drilling equipment and an automatic drop device was developed to check the cone resistance value and the dynamic cone penetration test value and analyze the correlation with the standard penetration test value to confirm its applicability at the mountain solar power generation site. As a result, the cone resistance value is q_d = 0.46 N and the dynamic cone penetration test value is N_d = 1.58 N, confirming a value similar to the results of existing researchers to secure its reliability.

• Korean Journal of Optics and Photonics
• /
• v.12 no.2
• /
• pp.91-97
• /
• 2001

We present a fiber Bragg grating (FBG) sensor system for measuring static and high-speed dynamic strains with a resolution of about $5\mu$strain. This sensor system demodulates signals from the FBG sensor utilizing a compensated tunable narrow bandpass filter. We have placed a set of twelve FBGs to concrete specimen and measured its internal stress under various applied load conditions.itions.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.9
• /
• pp.5-12
• /
• 2005

SPT hammer energy and its delivery are hon to influence the N value. The SPT hammer energy is classified into theoretical energy, velocity energy, rod energy and dynamic efficiency. In this study, the rod energy and the velocity energy are measured directly by PDA and Digital Line-Scan Camera which are most widely used type of SPT apparatus in Korea. The Dynamic efficiency is calculated through measured data. As the results of this study, the averages of rod energy ratio of donut, safety and automatic hammer are measured at 49.57, 61.60, and at $87.04\%$ by FV method. The averages of hammer velocity of donut, safety and automatic hammer are measured at $3.177{\pm}0.872$, $3.385{\pm}0.681$, and at $3.651{\pm}0.550$ m/s by Digital Line-Scan Camera, with the dynamic efficiencies at 0.732, 0.801, and 0.973 respectively.

• Tunnel and Underground Space
• /
• v.17 no.2 s.67
• /
• pp.83-89
• /
• 2007

Impact-echo test is a non-destructive testing method to determine dynamic properties of a material. This presentation introduces the experimental set-up and procedure of the test for rock specimens. In addition, the test results of domestic rocks collected in 5 different areas, a cement mortar and aluminium alloy are presented. The test results include resonance frequencies of P- and S-wave as well as damping ratios of the described 7 different materials. The differences between dynamic and static values of elastic moduli are about 10%, while the dynamic Poisson's ratios are greater than the static Poisson's ratios by at least 0.07. The damping ratio is dependent on the joint density and degree of weathering of a rock specimen.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.12
• /
• pp.33-39
• /
• 2018

In this study, important characteristics were identified for the Geosynthetic-soil interface using overburden pressure and saltwater and fresh water to evaluate silt shear behavior of the Geosynthetic-soil interface. In addition, waste landfill can secure spaces for waste disposal in the sea and this spaces can be used for additional facilities which will be necessary in the future. Analysis of behavior characteristics on interface of Geosynthetic-soil shows that, if analyzed using standard consolidometers, the consolidation stress of fresh water increased significantly more than saltwater. When analyzed using cyclic shear apparatus, saltwater and freshwater in both conditions, the displacement value increases as the wire gauges become closer to the lower module, and the shear fracture tends to occur radically under saltwater conditions than fresh water. Therefore, seawater, fresh water that act on the interface of geosynthetic-soil, and installation of facility using geosynthetic should be considered as important parameters that are essential for the dynamic design factor of the water controlling facility.

• Computational Structural Engineering
• /
• v.2 no.3
• /
• pp.77-84
• /
• 1989

Small-scale models of reinforced concrete beam-column joints and anchorage-bond specimens were subjected to large cyclic displacements at two rates. To assess damage, free vibration tests were conducted. The reliability of the modeling techniques was established by comparison of the results for the slower rate with those obtained from the full-scale tests on prototype. The higher rate of loading caused a greater damage than that at the slower rate. This was evidenced by the measurements of the stiffness obtained from the free-vibration test. The relatively greater extent of damage appears to result from the different bond behavior at different rates of loading.