• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1088-1092
• /
• 2017

In this study, a comparison of dynamic pressure data measured in hot-firing tests of liquid rocket engine gas generators with different types of dynamic pressure sensors is presented. The dynamic pressure sensors of different types and manufacturers have exhibited different dynamic pressure due to the influence of thermal shock. However, for the characteristic frequencies and RMS(root mean square) values which are important factors for the analysis of combustion instability, the differences between sensors have been found to be negligible.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.2
• /
• pp.83-93
• /
• 2020

Dynamic pressure transducer needs to be flush-mounted on hardware due to frequency response characteristics of pressure transmission system. However, it is sometimes necessary to be mounted in recessed configuration due to insufficient space for sensor installation and for protection of sensor from thermal damage. Dynamic response characteristics should be considered due to distortion of original dynamic pressure signal in the pressure transmission system. In this study, small perturbation model and 2nd order reduced model were compared with experiments and a guideline for selecting a frequency response model was suggested.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.89-96
• /
• 2013

Combustion pressures were measured to study combustion stability for an oxygen rich preburner by both of static and dynamic pressure sensors. The resolutions of each static and dynamic pressure sensor are the 1,000 Hz and 25,600 Hz, respectively. The nominal combustion pressure of the preburner was 200 bar but 80 bar was used at the several initial tests for the safety reason. Two stage ignition was applied to reduce the ignition impact for every tests including the tests with 200 bar combustion pressure. The tests lasted for 10 sec. max. and a little fluctuations of pressure was observed during the main mode. The measured pressures were studied by FFT analysis and no noticeable frequency coupling was found. Thus the preburner can be regarded as stable and it can be utilized for further study on staged combustion cycle liquid rocket engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.65-69
• /
• 2012

An oxygen rich preburner was tested and the responses from the pressure sensors were studied with FFT analysis. Since the limited capability of the static sensor, less than 250 Hz frequency domain was investigated and compared to the results of the dynamic sensors. As a result, 60 Hz harmonics were presented dominant in the combustion pressure and oxygen inlet pressure. While similar harmonics were shown with the dynamic sensor, it indicated that harmonics less than 60 Hz were very minor and the high frequency is more important.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.108-119
• /
• 2020

Dynamic pressure sensor used in liquid rocket engine combustor and gas turbine is recess-mounted usually because it should work in high temperature environment. Although recess-mounted method can protect it from combustion gas in high temperature, tube resonance occurs in a tube-cavity system. To reduce it, the infinite tube probe(ITP) was introduced in this study. The ITP model suggested in previous literature was validated with experimental data and frequency response characteristics were analyzed. Guidelines for designing the ITP were suggested as frequency response profiles varied with geometric information and physical properties using this model.

• Journal of Sensor Science and Technology
• /
• v.11 no.3
• /
• pp.125-131
• /
• 2002

Respiratory air flow rate is necessarily measured for the pulmonary function evaluation. The currently used devices are exposed to the problems of measurement reliability and cross-patient infection. The present study introduced a new technique which converted the bidirectional air flow rate into averaged dynamic pressure based on the famous Bernoulli's energy conservation principle. Single use plastic sensing element was assembled within the flow tube(mouth piece) made of paper, which was named "functional single use flow tube". Experiment demonstrated only ${\pm}1.5%$ relative error in the standard 3L volume measurement procedure well within the error limit suggested by the American Thoracic Society(ATS). Disposable use design completely eliminated cross-patient infection. The present device is best useful and safe for clinical respiratory air flow measurement such as spirometry.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.3
• /
• pp.96-102
• /
• 2016

The 7tonf-class power pack test at turbopump test facility in Naro space center was performed for confirmations of starting/running/ending operation characteristics before 7tonf rocket engine hot-firing test. The dynamic pressure mounted on a combustion chamber of gas generator is measured under 0.2 bar which does not conditioned to the unstable combustion. The analysis results of RPM and acceleration sensors mounted on the turbopump, the power pack test was performed to the estimated RPM with the stable combustion.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.93-100
• /
• 2020

The turbopump of the liquid rocket engine adapts an inducer to minimize the cavitation due to the variations of the propellants supply condition. However, the inducer introduces cavitation instabilities which are well-known problems in the engine development. In this paper, operational characteristics by the cavitation instabilities are analyzed and the reliability of the engine is checked when the first stage engine of the KSLV-II is tested at the low inlet pressure conditions. The characteristic frequencies representing the cavitation instabilities of the LOx pump are clearly found in various high frequency sensor signals around the entire engine in addition to the LOx and fuel pump.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.123-131
• /
• 2002

In this paper, characteristics of cryogenic liquid oxygen was examined during cold flow of KSR-III main engine at each stage. The effect of venting was examined at the stage of cooling and at the pressurization stage, the interaction between nitrogen gas and liquid oxygen was also examined. The characteristic of liquid oxygen in the engine manifold was analyzed. The results showed that venting was the primary role at the cooling process and the interaction of nitrogen gas and liquid oxygen in the run tank is limited at the surface area. With the sampling rate of 1KHz static and dynamic pressure were measured in the rocket engine manifold and in the LOX supply equipment. 32.5mm and 38mm orifice were installed for the tests and pressure condition of liquid oxygen was 23Bar, 29Bar, 41Bar. Increase of orifice diameter and decrease of supply pressure reduced the perturbation of pressure in engine manifold.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.4
• /
• pp.491-499
• /
• 2009

The determination of response characteristics for pressure sensors is routinely limited to static calibration against a deadweight pressure standard. The strength of this method is that the deadweight device is a primary standard used to generate precise pressure. Its weakness lies in the assumption that the static and dynamic responses of the sensor in question are equivalent. Differences in sensor response to static and dynamic events, however, can lead to serious measurement errors. Dynamic techniques are required to calibrate pressure sensors measuring dynamic events in milliseconds. In this paper, a dynamic calibration using negative going dynamic pressure is proposed to determine dynamic pressure response for piezoelectric sensors. Sensitivity and linearity of sensor by the dynamic calibration were compared with those by the static calibration. The uncertainty of calibration results and the goodness of fit test of linear regression analysis were presented. The results show that the dynamic calibration is applicable to determine dynamic pressure response for piezoelectric sensors.