• The Journal of Engineering Geology
• /
• v.11 no.3
• /
• pp.245-254
• /
• 2001

The experimental study on disposal cover through the performance test facility offers reliability in the safety of near surface disposal of low and intermediate level radioactive waste. To ensure the long-term safety of the repository, the impermeability, integrity, resistance to degradation and ease of maintenance might be considered as the basic performance requirement of the disposal cover. considering the difficulties to meet these performance requirement by using single layer, the disposal cover design which is composed of top layer, middle drainage layer and bottom low permeability layer is schemed for the test facility. The water balance of the cover was evaluated by using HELP code. For the long-term monitoring of the soil moisture content and matric potential, TDR probes and tensiometers will be installed in 6 test cells. Each test cell is dimensioned 3$\times$3$\times$3.3m.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.6
• /
• pp.198-204
• /
• 2010

The cover of truck agitator give in a part to prevent the lower flowing of fresh concrete when the concrete are transported from the ready mixed concrete plant to the construction field. As a result of the question data, it show up a dirty image to the general civil society. Due to the above image, it is predicted to affect the image of the construction company, so we did the site experiment of the flowing, the amounts of air, the temperature change of concrete with the concrete left in the site, to find out the usefulness. Also, for the comparing with this, we got the result by doing the inner experiment with the same condition. As the result of the experiment, the cover of truck agitator affect little to the reduction of slump. The change of the air amount, regardless of the existence of cover, was not effected much in proper level until 60minutes. In addition, The compression strength was proper to the goal design strength until 90minutes regardless of the cover of truck agitator exist or not exist.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.5
• /
• pp.9-17
• /
• 2005

In the early stage of helicopter design, an optimal configuration is usually determined after a numerous parametric study about the aerodynamic performance due to geometric variation. In order to improve the aerodynamic performance of a shrouded tail rotor, optimization of the tip clearance gap between blade and shroud, the blade planform shape, and the arrangement of blade spacing is required. In the present study, the aerodynamic performance characteristics of a shrouded tail rotor due to geometric variation was investigated by using an inviscid compressible unstructured mesh flow solver for rotary wings.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1999.07a
• /
• pp.326-331
• /
• 1999

1997년말 현재 우리나라의 시설재배면적은 47,264㏊이며 이 중 85%인 40,000㏊ 정도가 무가온 단동비닐온실이다. 이런 단동온실은 난방을 하지 않고 그림 1과 같이 보온덮개를 사용하는 무가온 재배를 하고 있으며, 온실내에 보온덮개를 덮기 위한 터널을 설치하고 있는데 이 터널의 설치에 사용되는 골조는 강선 또는 FRP재로 길이는 1.8-2.4m이고, 터널폭은 0.9-l.2m 정도로 하고 있다. (중략)

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.06a
• /
• pp.215-222
• /
• 2000

반복하중을 받는 대부분의 토목구조물은 정적하중보다 훨씬 낮은 하중에서 파괴가 발생하는 경우가 있는데 이러한 현상을 피로라고 하며, 특히 강교량을 구성하는 부재중에서 2차 부재에 해당되는 덮개판, 수평보강재, 수직보강재, 거셋트 등의 용접부에서는 여러 원인으로 인해서 피로손상이 발생하게 되어 결국에는 구조물의 성능에 크게 영향을 미치게 된다. (중략)

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.1
• /
• pp.90-99
• /
• 1999

In this work, we consider the effect of the presheath on the ion angular distribution. The recent shows the ion-neutral collision in the presheath and the calculated energy flux with the ion angular distribution at the presheath edge in plasma reactor. We also propose a new approximation analytical model for the ion angular distribution and the energy flux distribution with ion temperature. The ion passing the presheath region, Shows a ion scattering effect without ion-neutral collisions. This because the kinetic energy by the ambipolar diffusion field is changed by the gas collision,. Using the proposed approximation analytical model, we show the simulated results of a deposit profile on variable trench shape.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.1-9
• /
• 2003

Detailed flow of a shrouded tail rotor in hover is studied by using a compressible inviscid flow solver on unstructured meshes. The numerical method is based on a cell-centered finite-volume discretization and an implicit Gauss-Seidel time integration. Numerical simulation is made for a single blade attached to the center body and guide by the duct by imposing a periodic boundary condition between adjacent rotor blades. The results show that the performance of an isolated rotor without shroud compares well with experiment. In case of a shrouded rotor, correction of the collective pitch angle is made such that the overall performance matches with experiment to account for the uncertainties of the experimental model configuration. Details of the flow field compare well with the experiment confirming the validity of the present method.

• Journal of Aerospace System Engineering
• /
• v.16 no.4
• /
• pp.1-9
• /
• 2022

A design factor analysis was conducted to reduce the thrust reduction in the off-design, due to the driving of the aerospike pintle nozzle. The close (NPR 100) as well as the open (NPR 11) stroke were fixed, as under-expansion conditions. The pintle contour, pintle head radius (R), cowl angle (θ), and cowl exit length (L) were selected as design factors. The change in thrust was analyzed, using a verified numerical analysis technique. First, the pintle head radius and the length of the cowl exit had little influence on the thrust. The cowl angle changed the mass flow rate by affecting the effective nozzle throat area, and created a reverse pressure gradient at the cowl exit. As a result of applying the dual aerospike contour, it was confirmed that the thrust in the design-off increased by approximately 1.2%, compared to the reference case and by approximately 3.4% compared to the worst case.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.49-56
• /
• 2020

High temperature heat generated during rifle firing not only degrades the performance of the weapon, but also limits the user's operation. In this study, temperature change of handguard according to firing was measured with reference to Human Engineering criteria and the operability according to material was examined. Accordingly, for the firing test, three types of Korean rifle and one overseas model were selected for each material of handguard, and firing test was conducted using a contact type temperature meter. The test result shows that using a plastic handguard with low thermal conductivity and aluminum handguard with high thermal conductivity enabled the rifles to be operated with bare hands even when firing at more than 100 rounds at low atmospheric temperature. However, when firing more than 60 rounds at over 20℃ atmospheric temperature, aluminum handguard use is limited. When firing quickly over 100 rounds, handguard use is restricted regardless of its fabrication material. To eliminate operational limitations by overheating, it is necessary to eliminate direct contact with skin using gloves, vertical grips, etc. This study examined the operability of rifles in terms of thermal risk, and the resulting study results are expected to be used as basic data for Human Engineering of other rifles and munitions.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.2
• /
• pp.175-182
• /
• 2013

The purpose of this study was to observe and analyze the initial marginal bone resorption changes according to the patterns of cover screw exposures during healing period followed by implants installation. Total 64 fixtures(TiUniteTM, NobelBiocare, Sweden) were installed in partially edentulous jaws of 28 patients, who were selected retrospectively and were shown at least one cover screw exposure. Cover screw exposures were defined at 1 month recall. According to the patterns of exposures, groups were categorized into group 1 (No exposure), group 2 (pin-point exposure), group 3 (less than 1/2 of cover screw), group 4 (more than 1/2 of cover screw), group 5 (total exposure). Periapical radiographs were taken in purpose of changes of marginal bone level between installation and 2 month recall. Healing abutments were secured on the exposure groups at 2 month recall. Results were as follows: 1. Marginal bone resorptions were identified whenever cover screws were exposed. 2. Group 2 and 3 were shown significantly increased bone loss more than other group (P <.05). 3. Group 4 and 5 were shown significantly increased bone loss more than group 1, however, less than other groups ( P <.05). Conclusionally, cover screw exposure may cause marginal bone resorptions, therefore, early connection of healing abutment is clinically helpful.