• Fire Science and Engineering
• /
• v.33 no.6
• /
• pp.186-189
• /
• 2019

NFSC 202 stipulates that if a loudspeaker or wiring on one floor of a building is shorted because of fire, it should not interfere with the fire notification on the other floors. To address this problem, this study proposes an ultrasonic transmitter/receiver consisting of an ADC, HPF, and LPF in an emergency broadcasting system that can operate regardless of the volume level of the amplifier output loudspeaker capacity. After transmitting the transmission frequency at -12 dB (110 kHz), it is received at -18 dB by transmitting -12 dB in case of short circuit depending on the frequency characteristics. Typically, depending on the loudspeaker capacity, it is received from -24 dB to -66 dB. In case of disconnection, it exceeds -66 dB and no data are received. It is also possible to check the track status during fire or general broadcasting. Thus, it was confirmed that the system is suitable for NFSC 202 regulations. Furthermore, as the current system is replaced, the inspection or test criteria should be amended or revised.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.103-109
• /
• 2008

In this papaer, a new type of ${\lambda}_g/4$ short stub band pass filter and ${\lambda}_g/2$ open stub band pass filter are purposed. Both are designed using FSCS technique for harmonic suppression. The proposed filters that used FSCS technique and a broadband stop filter is integrated to band pass filter to suppress the harmonics. The BSF are also placed between stubs so that the size is larger than prevent as compared to conventional one. The propose filters have center frequency of 5.8 GHz, bandwidth of 50% and harmonics suppressin is 120% has in bandwith. The measurement results in the case of ${\lambda}_g/4$ short stub filter, insertion loss of 0.5 dB, return loss of 14 dB are achieved and in the case of ${\lambda}_g/2$ open stub filter, loss of 0.8 dB, return loss of 14.4 dB are achieved. The simulation results and the measurement results are almost the same.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.3
• /
• pp.15-20
• /
• 2004

In this paper, a wideband two-layer H-shaped microstrip antenna for WLAN is designed. To increase the bandwidth of microstrip patch antenna a configuration of stacked type using parastic element is used. Furthermore, to reduce the size of microstrip patch antenna, two techniques are employed . the first one is H-shaped patch type and the second one is that the main radiator and parastic patch are shorted to the ground plane using ten shorting posts. The antenna bandwidth and radiation characteristics are calculated by ENSEMBLE ver. 5.0 simulation software, and compared with the experimental results. Experiment results show that the bandwidth of antenna in 740MHz centered at 5.46㎓(13.5%), which is close agreement with the calculations, 770MHz(13%). Also, the antenna size can be reduced by 71.5% compared with the half wavelength rectangular microstrip antenna using the same substrate at the same frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.167-173
• /
• 2008

In this paper, the flexible narrow bandpass filters (BPFs) with ${\lambda}$g/4 short and ${\lambda}$g/2 open stubs by microstrip line on duroid substrate are suggested. These BPFs with narrow bandwidth show flexible bandwidth with variation of the position of the stubs using the Qe (external quality factor) without changing the impedance value at microwave range. On the other hand, by replacing the series quarter-wavelength connecting lines with the equivalent T-shaped line of bandstop filter(BSF), the compact stub bandpass filter with harmonics suppression can be realized. The BPF with ${\lambda}$g/4 short stubs shows the insertion loss of 2.1 dB and the return loss of 18 dB and BPF with ${\lambda}$g/2 open stubs shows the insertion loss of 1.2 dB and the return loss of 21.9 dB at the center frequency of 5.8 GHz and the bandwidth of 10 %.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.8
• /
• pp.114-120
• /
• 2008

In this paper, we extract the parasitic elements of the metal-insulate-metal(MIM) capacitor using short-open calibration (SOC). The scattering matrixes of short, open, and MIM structures in strip lines are measured by full electro-magnetic (EM) simulator and vector network analyser. The full EM simulations are performed by finite element method (FEM) that was fitted three dimensional structure analysis. The electro-magnetic effects of MIM capacitor laminated in the multi-layered structures are proposed the II equivalent circuit with lumped elements, and the relations between the measured scattering parameters of the MIM structures and lumped elements in the circuits are shown by performing 2 port network analysis. The extracted lumped elements using the proposed SOC method are independent to frequencies.

• Journal of IKEEE
• /
• v.7 no.2 s.13
• /
• pp.223-229
• /
• 2003

In this thesis, the characteristics of an inverted-F antenna for the 2.4GHz and 5.8GHz zwirless local area network(WLAN) have been analysed in terms of the variation of design parameters. The antenna can be integrated on WLAN for notebook printed circuit board, and the characteristics in terms of the variation of the gap between feed line and shorting stub, gap between antenna's leg and ground plane, antenna leg's width, substrate's height and dielectric constant are analysed. By using these characterization plot of design parameter, the tuning techniques are proposed to design optimum antenna. The designed antenna has 170MHz, 500MHz frequency bandwidth ,VSWR is 1.6, 1.14 and 3.5dBi gain.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.1
• /
• pp.84-90
• /
• 2010

In this paper, a novel voltage-controlled oscillator (VCO) using the harmonic control circuit based on the composite right/left-handed (CRLH) transmission lines (TLs) is presented to reduce the phase noise without the reduction of the frequency tuning range and miniaturize the circuit size. The phase noise is reduced by the novel harmonic control circuit having the short impedances for the second- and third-harmonic components. The proposed harmonic control circuit is designed by using the CRLH TLs with the dual-band characteristic by the frequency offset and phase slope of the CRLH TLs. The high-Q resonator has been used to reduce the phase noise, but has the problem of the frequency tuning range reduction. However, the frequency tuning range of the proposed VCO has not been reduced because the phase noise has been reduced without the high-Q resonator. The miniaturization of the circuit size is achieved by using the CRLH TLs instead of the conventional right-handed (RH) TLs. The phase noise of VCO is -119.17 ~ -117.50 dBc/Hz at 100 kHz in the tuning range of 5.731 ~ 5.938 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.311-316
• /
• 2015

This paper presents a design method for thin but wideband absorbers using resistive sheets. Its equivalent circuit consists of a series RLC resonant circuit and a short-terminated transmission line. Based on this equivalent circuit, we presented the three conditions for an electromagnetic absorber which has a thickness less than a quarter wavelength and wide absorption bandwidth at center frequency. By using an root-finding algorithm, the equivalent resistance, capacitance, and inductance of the absorbers are obtained. These equivalent circuit values for the absorber surface can be realized by a 2D periodic cross-shaped structure which has required surface resistance. Using the design method, we have designed the absorber which has 18.75 mm($67.5^{\circ}$ electrical length) thickness and 90 % absorption bandwidth of 116 % bandwidth at 3 GHz.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.5
• /
• pp.21-26
• /
• 2014

This paper proposes a frequency reconfigurable antenna which operates at not only LTE but also other currently serviced bands. The high band(1,710-2,170 MHz) performance was satisfied through PIFA structure, and the low band performance through the additional RF Switch by changing the state between SW1 and SW2. When the RF switch is SW1 state, the operation bandwidth is 782-907 MHz (GSM), and 738-861 MHz (LTE) at OFF state. The proposed antenna has a omni-directional radiation pattern and measured peak gains were 0.04-4.68 dBi at the SW1 state and 0.92-1.53 dBi at the SW2 state, respectively. Judging from the results, proposed reconfigurable antenna is expected to be applied to LTE-Advanced mobile terminals since the antenna shows an outstanding performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.4
• /
• pp.672-678
• /
• 2017

In this paper, we studied a design method for a broadband quasi-Yagi antenna (QYA) for terrestrial digital television (DTV) reception. The proposed antenna is composed of a dipole driver, a rectangular patch type director close to the dipole, and a ground reflector printed on an FR4 substrate. A balun between a microstrip line and a coplanar strip (CPS) line is a rectangular patch inserted along the center of the CPS. The end of the balun is connected to the CPS line through a shorting pin. An antenna, as an design example for the proposed antenna, is designed for the operation in the frequency band of 470-806 MHz for terrestrial DTV, and the characteristics of the designed antenna are examined. The antenna has a good performance such as a frequency band of 430-842 MHz for a voltage standing wave ratio < 2, a gain > 3.7 dBi, and a front-to-back ratio > 7.4 dB.