• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.5
• /
• pp.644-654
• /
• 2003

An analytical solution for a vertically stratified viscous flow in a microchannel with a rectangular cross-section is constructed, assuming fully developed laminar flow where the interfaces between the fluid layers are flat. Although the solution is for n-layer flow, restricted results to symmetrical three-layer flow are presented to investigate the effects of the viscosity and thickness ratios of the fluid layers and the aspect ratio of the microchannel on the flow field. Relations between the flow rate and thickness ratios of the fluid layers with varying viscosity distributions are found, considering the cross -sectional velocity profiles which vary noticeably with the three parameters and differ significantly from the velocity profiles of the flow between infinite parallel plates. Interfacial instability induced by the viscosity stratification in the microchannel is discussed referring to previous studies on the instability analysis for plane multilayer flow. Exact solution derived in the present study can be used for examining a diffusion process and three -dimensional stability analysis. More works are needed to formulate the equations including the effects of interfacial' tension between immiscible liquids and surface wettability which are important in microscale transport phenomena.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.101-107
• /
• 1998

A three-dimensional multi-phase flow is simulated around a smooth tire. This simulation is conducted by solving Navier-Stokes equation with a k-$\varepsilon$ turbulent model. The numerical calculations are carried out by modeling a multi-phase free surface flow mixed with air and water at the inlet. The numerical solutions show an intuitively resonable behavior of water around a moving tire. The calculated pressure around the tire surface along the moving direction is presented. The moving velocities of the tire are chosen to be 30, 40, 60, and 70 km/h. The numerically simulated pressures around the tire are compared with existing experimental data. The comparison shows a new possible tool of analyzing a hydroplaning phenomenon for an automobile tire by means of a computational fluid dynamics.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1998.11a
• /
• pp.155-158
• /
• 1998

다층 신경회로망의 모델의 크기는 적용분야에 따라서 임의로 선택되어지고, 최적의 네트워크 크기는 긴 시간에 걸친 시행착오를 통하여 결정된다. 본 논문에서는 은닉충의 뉴런 수를 학습 과정에서 유동적으로 결정하는 역전파 알고리즘을 제안한다. 기존의 Narendra의 모델의 동정에 대하여 제안한 알고리즘의 유용성을 비교 검토하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.271-276
• /
• 1994

본 연구에서는 외부 호스, 내부 충진유 및 탄성체 핵으로 구성된 다층 재질의 무한히 긴 원통형 실린더가 자유 흐름 중에 있을 때, 유체 유동에 의한 난류 경계층내 벽면 압력 변동(wall pressure fluctuation)이 내부 탄성체 핵의 표면에 미치는 영향을 분석하기 위하여 난류 경계층에 의한 다층 재질의 실린더 내부 압력 변동 해석 이론을 정립하였다. 본 해석 이론에서는 파동 방정식을 이용하여 외부 호스 벽면 압력에 대한 전달 함수를 도출하고, 난류 경계층내 벽면 압력 변동은 Corcos Model을 기초로 하여 Strawderman이 제안한 실험식을 사용하여 추정하였다. 또 이를 바탕으로 자유 흐름 속도 변화등에 따른 실린더 내부 압력변도의 변화를 분석하여 보았다.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.04a
• /
• pp.217-220
• /
• 2001

• Journal of Ocean Engineering and Technology
• /
• v.13 no.2 s.32
• /
• pp.147-158
• /
• 1999

Warm or waste water discharged from offshore-based facilities often causes environmental polution as it is transported to coastal area due to tidal actions. In this research a floating-type current control structure is introduced in order to reduce the pollutant spreading in the coastal area. Effectivenss of the structure is investigated through the numerical experiment which is based on a 3-D finite difference multi-level scheme. The warm-water spreading in the bay is reduced when the draft of the structure increases and its optimum draft is found to be between 0.25h and 0.65h, where h is the water depth. The proposed structure is also tested in the Gohyun Bay and it ts proven to be applied to controllling pollutant spreading if its draft is properly chosen.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.2
• /
• pp.70-77
• /
• 1999

The disturbance of oil-water interface confined between tandem fences caused by a sequence of traveling vortices below the interface is investigated. The traveling vortices are assumed to be those detached from the tip of the fore fence. The potential flow is assumed and the density interface is replaced as a sheet of vortex. The shape of the interface is predicted by tracing a finite number of marker particles placed at the interface. The velocity of the marker particles is determined by the Biot-Savart integral along the vortex sheet plus the contribution from the traveling point vortices. The rate of change of vortex-sheet strength is predicted by using an evolution equation for vorticity. The calculated results obtained for various conditions demonstrate that the large amplitude of interfacial wave following the moving vortek can be generated by the vortices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.206-206
• /
• 2009

RF Magnetron Sputtering 방법을 통해 ZnS:Mn 박막 형광체를 증착한 다층 TFEL (Thin-Film Electroluminescent) Backlight 소자를 제작하였다. Alumina 기판 위에 Au 전극과 PMN 후막 유전체를 Screen printing 기법으로 층을 형성하였다. 그 위에 MgO 박막 유전체를 E-Beam 장비를 이용하여 증착 후, ZnS:Mn 박막 형광체를 50 W 의 저전력으로 약 8000 ${\AA}$ 두께로 증착하였다. 형광체는 Sputter 증착 시 Sulfur 부족 현상을 보상해주기 위해 ZnS:Mn (0.5%) Target 에 2 at % 의 Sulfur를 첨가하였으며, 상부 전극으로 사용할 ITO 는 DC Magnetron Sputter 를 이용하여 증착하였다. 어닐링 공정은 Air 분위기에서 급속 열처리 장치 (RTA, Rapid Thermal Annealing) 을 이용하여 600 $^{\circ}C$에서 20 분 진행하였다. 이러한 과정들을 통해 저전압 고휘도의 TFEL Backlight 소자를 제조할 수 있었다.

• Journal of KSNVE
• /
• v.6 no.5
• /
• pp.671-677
• /
• 1996

This paper presents the analytical method for predicting turbulence- induced noise in the multilayered cylinder composed of an outer hose, an inner fluid and an internal core. It is assumed that an infinite axisymmetric cylinder is located horizontally in water with free stream velocity and the turbulent boundary layer (TBL) surrounding the outer hose is fully developed and homogeneous. The transfer function at the core surface due to the propagation of the pressure fluctuation within the TBL is formulated using the linearized Navier-Stockes equation for solid and fluid. In the estimation of the energy spectrum of wall pressure fluctuation, the empirical formula proposed by Strawderman based on the Corcos model is used. A general algorithm for the calculation of the pressure level at the surface of a core, that is, turbulence- induced noise, is presented. Through the detailed numerical simulation, it is found that the major noise mechanism is the propagation of the bulge wave along hose.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7990-8000
• /
• 2015

Plant factories are plant cultivation systems which produce farm products uniformly under the controlled environmental condition regardless of seasons and places. Thermal flow in the plant factory is an important parameter in cultivating plants. In this research, we study thermal flow characteristics for a hybrid plant factory with multi-layer cultivation shelves using computer simulation techniques. In order to obtain numerical solutions for thermal flow characteristics, a finite volume method was applied. We consider a low-Reynolds-number ${\kappa}-{\epsilon}$ turbulence model, incompressible viscous flows, and pressure boundary conditions for numerical simulation. Commercial software Solid Works Flow Simulation is then used to investigate characteristics of thermal flows in the plant factory applying several different inflow air velocities and arrangements of cultivation shelves. From numerical analysis results, we found that temperatures in cultivation shelves were uniformly distributed for Case 3 when the inflow air velocity was 1.6 m/s by using a blower in the plant factory. However in Case 1 lower temperature distributions were observed in test beds, TB2 and TB3, which indicated that additional temperature control efforts would be required. Average shelf temperature increased by $3^{\circ}C$ using artificial light source (DYLED47) with 50% blue and 50% red LED ratios. Korea Academia-Industrial cooperation Society.