• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.4
• /
• pp.473-478
• /
• 2011

The extent of a rectangular conducting plane for measuring electromagnetic interference is discussed. Mutual coupling between the transmit and receive antennas is negligible, the effects of the ground plane on the normalized site attenuation(NSA) are considered by applying GTD(Geometric theory of diffraction). The calculation was done for the case that measuring distance(d) was 3 m for both horizontal and vertical polarizations. As the result, the size of the rectangular ground plane almost never affects upon NSA for horizontal polarization, but for vertical case, when both width and length of the rectangular plane are several times as long as distance, the effects of the edges are reduced under 1 dB.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.11
• /
• pp.1-11
• /
• 1999

In this paper, the effects of superstrate on the radiation patterns of dipole on cylindrical bianisotropic substrates were studied. Special constitutive relations are used to describe the bianisotropic properties of a material, such that the Green's function can be formulated. Electromagnetic fields and boundary conditions in spectral region were used to find Green's function of the spectral representation and electromagnetic fields in space region were derived through inverse Fourier transformations of fields in spectral region using asymptotic formula for far zone. Radiation characteristics of axial Hertzian dipole on superstrate loaded cylindrical bianisotropic substrates were obtained. The effects of bianisotropic superstrate on the radiation properties of the antennas including beam scanning, directivity enhancement, dark-region illumination, and on horizon radiation, are discussed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.75-82
• /
• 2009

In this paper, we proposed a U-shaped broadband RFID tag antenna with a parasitic element operating at UHF band. The proposed tag antenna consists of a U-shaped half wavelength dipole antenna and an inverse U-shaped parasitic element inside the U-shaped dipole antenna. In order to have good impedance matching, the commercial tag chip is attached to the lower center of the rectangular shaped feed. On the condition of VSWR<2, the tag antenna had the measured bandwidth of 4.96 % from 882 to 927 MHz and showed the gain deviation of less than 3.16 dB. On the condition of VSWR<5.8, the tag antenna satisfies the worldwide UHF RFID bandwidth and is showed the gain deviation of less than 5.07 dB. The minimum gain deviation characteristic appears near the center of bandwidth which minimizes variation of gain deviation characteristic with respect to the frequency.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.3
• /
• pp.32-39
• /
• 2009

In this paper, system optimization design technique of an impulse ground penetrating image radar (GPIR) in time domain is proposed to improve depth resolution of the system. For the purpose, time domain analysis method of key components such as impulse generator and UWB antenna is explained and by simulation, parameters of each component are determined. In particular, by standardizing the impulse signal, spectrum efficiency of a radiated impulse signal is improved and a U-shaped planar dipole antenna for a UWB antenna is developed. By equipping a parabolic metal reflector with the proposed antenna, external noise is prevented and the ability of radiating an input impulse into ground is improved. In addition, to remove ringing effect of the propose antenna which causes serious degradation of the system performance, resistors are loaded at the edge of the antenna and then Tx and Rx UWB antennas are optimized by simulation in time domain. For images of targets buried under the ground migration technique is applied and influence of tough ground surface on distortion of received impulse signals is reduced using technique of noise and signal distortion reduction in time domain and its time resolution is enhanced. To verify the design optimization procedure, a prototype of an GPIR and an artificial test field are made. Measurement results show that the resolution of the system designed is as good as that of a theoretical model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.1008-1016
• /
• 2013

SAR measurement which was applied only to the mobile phone has been expanded in the Korean radio regulation law to the portable wireless communication equipments within 20 cm from the human body since Jan. 2012. The two-way radio operating at 150 MHz frequency band was newly included following the revised radio regulation in the target equipment of measurement. SAR measurement system at 150 MHz satisfying this regulation is necessary accordingly for SAR conformity assessment. The international SAR measurement standard(IEC 62209-2) includes the evaluation method on frequencies above 300 MHz, and the commercial SAR measurement system can measure SAR above 300 MHz only. The size of the reference dipole antenna(760 mm, return loss: -27.57 dB) and flat phantom ($1,300 mm(L){\times}900 mm(W){\times}200 mm(H)$), targeted SAR values for numerical analysis(1 g: 1.08 W/kg, 10 g: 0.77 W/kg) for SAR validation evaluation at 150 MHz frequency are proposed in this paper. The suggested dipole antenna and flat phantom are assembled and used to verify the conformity assessment of commercial SAR measurement system. The measured SAR values of 1 g and 10 g were obtained respectively to be 1.13 W/kg, 0.81 W/kg, and they satisfied the effective range(within ${\pm}10$ %) of IEC international standard. The standards based on this study are expected to be used for the domestic SAR measurement standard and IEC(International Electrotechnical Commission) international standard.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.381-391
• /
• 2010

In this paper, a novel frequency reconfigurable active array antenna(RAA) system, which can be reconfigurable for three reconfigurable frequency bands, is proposed by using commercial RF MEMS switches. The MEMS switch shows excellent insertion loss, linearity, as well as isolation. So, the system performance degradation of the reconfigurable system by using MEMS switches can be minimized. The proposed frequency reconfigurable active antenna system is consisted with the noble frequency reconfigurable front-end amplifiers(RFA) with the simple reconfigurable impedance matching circuits(RMC), reconfigurable antenna elements(RAE), as well as a reconfiguration control board(RCB) for MEMS switch control. The proposed RAA system can be reconfigurable for three frequency bands, 850 MHz, 1.9 GHz, and 3.4 GHz, with $2{\times}2$ array of the RAE having broadband printed dipole antenna topology. The validity of the proposed RFA as well as RAA is also presented with the experimental results of the fabricated systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.5
• /
• pp.523-532
• /
• 2008

In this paper, we proposed a U-shaped RFID tag antenna with isotropic radiation characteristic for the stable operation of RFID system. The proposed antenna is composed of a U-shaped half wavelength dipole and a rectangular-shaped feed. In order to have good impedance matching with a tag chip, the commercial tag chip is attached to the lower center of the feed. A gain deviation characteristic of the U-shaped tag antenna can be further improved by inserting a rectangular slit in the lower center of the U-shaped antenna body. On the condition of VSWR<2, the tag antennas of two structures satisfy the Korea UHF RFID bandwidth and showed the gain deviation of less than 1.63 dB and 0.74 dB for without slit and with slit, respectively. On the condition of VSWR<5.8, the U-shaped tag antenna showed the gain deviation of less than 3.8 dB and 1.2 dB for without slit and with slit, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.483-489
• /
• 2006

In this paper, new wideband lens amplifiers are proposed for C-band wireless communication service. In order to obtain the wideband property, all components of the proposed lens amplifiers are designed with balanced structure and wideband characteristics. Fat dipole antenna as the input and output antenna, balanced amplifier as amplifying components, and coplanar stripline(CPS) as the delay line fer the beam focusing are used fur composing the stable wideband lens amplifier. The $5{\times}5$ 2D lens amplifier has the characteristics that the absolute gain is 7.5 dB, the EIPG is 37.4 dB at 6 GHz, and the 3-dB gain bandwidth is 19.8 %.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1175-1184
• /
• 2008

Delay-sum back projection(DSBP) algorithm and the time reversal algorithm based on the finite-difference time-domain method are compared. The two algorithms, which operate in the time domain, can process the ultra-wideband (UWB) radar data to generate images that are close to the original location and shape of the target. For the experiment, the UWB radar consists of a network analyzer, a resistive V dipole antenna, a scanner, and a control computer. The radar aperture is synthesized by linearly scanning the antenna. A calibration procedure is applied to the measured data to remove signal distortion and clutter. The two algorithms are applied to the same data on the same platform. It is shown that the DSBP algorithm produces better images but takes longer time to produce the images than the FDTD-TR algorithm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4165-4170
• /
• 2012

In this paper, a method for the improvement in the gain and bandwidth of a microstrip-fed broadband planar quasi-Yagi antenna (QYA) is studied. The broadband characteristics of the QYA are achieved from the coplanar strip-fed planar dipole driver and a parasitic director close to the driver. In order to obtain stable gain variation over the required frequency band, a director and a ground reflector are appended to the driver having a nearby parasitic director. The QYA is fed through an integrated balun composed of a microstrip line and a slot line which are terminated in a short circuit. By adjusting the feeding point, a broadband impedance matching is obtained. A QYA with an operating frequency band of 1.75-2.7 GHz and a gain > 4.5 dBi is designed and fabricated on an FR4 substrate with dielectric constant of 4.4 and thickness of 1.6mm. The experimental results show that the fabricated antenna has good performance such as a broad bandwidth of 59.7%(1.55-2.87 GHz), a stable gain between 4.7-6.5 dBi, and a front-to-back ratio > 10 dB. The measured data agree well with the simulation, which validates this study.