• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.683-693
• /
• 2010

In this paper, we propose a new parallel mechanism for the legs of biped robots and the control of the robot's locomotion. A leg consists of two 3-DOF parallel platforms linked serially: one is an orientation platform for a thigh and the other is the 3-DOF asymmetric parallel platform for the shank. The desired locomotion trajectory is generated on the basis of the Gravity-Compensated Inverted Pendulum Mode (GCIPM) in the sagittal direction and the Linear Inverted Pendulum Mode (LIPM) in the lateral direction, respectively. In order to simulate the ground reaction force, a 6-DOF elastic pad model is used underneath each of the soles. The performance and effectiveness of the proposed parallel mechanism and locomotion control are shown by the results of computer simulations of a 12-DOF parallel biped robot using $SimMechanics^{(R)}$.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.3
• /
• pp.305-311
• /
• 2012

In this paper, we propose a gait generation method for quadruped robots using the xz-axis sway of the quadruped robot, which minimizes the shake of the quadruped robot and maximizes the stability margin. In the proposed method, the gait is generated based on wave gaits and the stability analysis uses the body tilt information of the quadruped robot according to the leg's height of leg. In addition, to reduce the impact on the body caused by the z-axis sway while walking, the proposed method generates the smooth walking movement trajectory with less impact by using Fourier series. Finally, to verify the applicability and effectiveness of the proposed method, we carry out the computer simulations and the real walking experiments with the implemented quadruped robot.

• The KIPS Transactions:PartB
• /
• v.13B no.2 s.105
• /
• pp.187-196
• /
• 2006

In 3D animation most people adjust the moving motion of their characters on various terrains by using motion data acquired with the motion capture equipment. The motion data can be used to present real human motions naturally, but the data must be captured again to apply to the different terrains from those given at acquiring mode. In addition, there would be a difficulty when applying the data to other characters, in that case the motion data must be captured newly or the existing motion data must be heavily edited manually. In this paper we propose a unified method to generate human motions of walking and running for various terrains such as flat plane, inclined plane, stairway and irregular face. With these methods we are able to generate human motions controlled by the parameters : body height, moving speed, stride, etc. In the proposed methods, the positions and angles of joint can be calculated by using inverse kinematics, and we calculate the trajectory of the swing leg and pelvis according to the cubic spline. With these methods we were presented moving motions using a model of a human body.

• Journal of KIISE:Software and Applications
• /
• v.30 no.11
• /
• pp.1092-1101
• /
• 2003

Most of 3D character animation adjusts the gait of their characters for various terrains, using motion capture data through the motion capture equipments. This motion capture data can be naturally presented as real human motions, which are to be adjusted according to the various types of terrain. In addition, there would be a difficulty applying motion capture data for other characters in which the motion data will be captured again or edited for the existing motion data. Therefore, this paper proposes a method that is to generate walking motion for various terrains, such as flat, inclined plane, stair, and irregular face, and a method that is to calculate the trajectory of the swing leg and pelvis. These methods are able to generate various gaits controlled by the parameters of body height, walking speed, stride, etc. In addition, the positions and angles of joint can be calculated by using inverse kinematics, and the cubic spline will be used to calculate the trajectory of the joint.

• Journal of the Korea Society for Simulation
• /
• v.20 no.1
• /
• pp.51-59
• /
• 2011

This paper is concerned with locomotion of dog-like quadruped robots that can adapt to various terrains, mainly dealing with implementation methods and characteristics of static and dynamic gaits. To this end, a 12-DOF robot is built in house, motional trajectories of its body and feet are generated mimicking biological life, and the corresponding leg joint angles are analytically obtained by inverse kinematics. Such joint angle data are then applied to the robot's ADAMS model for computer simulations so that the planned walk and trot gaits are both confirmed dynamically stable. However, contrary to the simulation results, previous trot patterns showed unstable behavior during experiments. This problem led us to analyze the reason, and in the course we discovered the importance of maximally utilizing the concept of WSM rather than ZMP and therefore reducing the gait period to secure the stability of dynamic gaits such as trot.

• Journal of the Korea Convergence Society
• /
• v.11 no.5
• /
• pp.175-182
• /
• 2020

The calculation of the optimal trajectory of the stepped top-down robot was made using a genetic algorithm and a computational torque controller. First, the total energy efficiency was minimized using the Red-Cold Generic Algorithm (RCGA) consisting of reproductive, cross, and mutation. The reproducibility condition related to the position assembly of the start and end of the stride and the joints, angles, and angular velocities are linear constraints. Next, the unequal constraint accompanies the condition for preventing the collision of the swing leg at the corner with the outer surface of the stairs, the condition of the knee joint for preventing kinematic peculiarity, and the condition of no moment in safety in the traveling direction. Finally, the angular trajectory of each joint is defined by fourth-order polynomial whose coefficient is to approximate chromosomes. This is to approximate walking. In this study, the energy efficiency of the optimal trajectory was analyzed by computer simulation through a biped robot with seven degrees of freedom composed of seven links.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.825-837
• /
• 2017

This paper describes a novel type of a walking rehabilitation robot that applies robot technologies to crutches used by patients with walking difficulties in the lower body. The primary features of the developed robot are divided into three parts. First, the developed robot is worn on the patient's chest, as opposed to the conventional elbow crutch that is attached to the forearm; hence, it can effectively disperse the patient's weight throughout the width of the chest, and eliminate the concentrated load at the elbow. Furthermore, it allows free arm motion during walking. Second, the developed robot can recognize the walking intention of the patient from the magnitude and direction of the ground reactive forces. This is done using three-axis force sensors attached to the feet of the robot. Third, the robot can perform a stair walking function, which can change vertical movement trajectories in order to step up and down a single stair according to the floor height. Consequently, we experimentally showed that the developed robot can effectively perform walking rehabilitation assistance by perceiving the walking intention of the patient. Moreover we quantitatively verified muscle power assistance by measuring the electromyography (EMG) signals of the muscles of the lower limb.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.3
• /
• pp.537-542
• /
• 2022

There is a limit to the current indoor air quality (IAQ) monitoring method using fixed sensors and devices. A mobile robot for IAQ monitoring was developed by mounting IAQ monitoring sensors on a small multi-legged robot to minimize vibration and protect the sensors from vibration while robot moves. The developed mobile robot used a simple gait mechanism to enable the robot to move forward, backward, and turns only with the combination of forward and reverse rotation of the two DC motors. Due to the simple gait mechanism, not only IAQ data measurements but also gait motion control were processed using a single Arduino board. Because the mobile robot has small number of electronic components and low power consumption, a relatively low-capacity battery was mounted on the robot to reduce the weight of the battery. The weight of mobile robot is 1.4kg including links, various IAQ sensors, motors, and battery. The gait and turning speed of the mobile robot was measured at 3.75 cm/sec and 14.13 rad/sec. The maximum height where the robot leg could reach was 33 mm, but the mobile robot was able to overcome the bumps up to 24 mm.