• Journal of Biosystems Engineering
• /
• v.24 no.3
• /
• pp.183-194
• /
• 1999

Using the dynamic model and simulation program TDA developed in the previous paper, effects of design parameters of an agricultural tractor-trailer system on its vertical seat vibrations were investigated. The tractor-trailer system was excited by traversing over a half-sine bump. The excitation frequencies were determined by traveling velocity of the tractor and a half-sine bump selected appropriately. TDA predicted the autospectra of the vertical seat accelerations with different values of design parameters and compared them to analyze their effects. The design parameters included positions of engine, cab, and seat mountings as well as their dynamic properties. The results of this study suggested guidelines with which an improved structure of tractor may be developed in the early stage of design for a better ride quality.

• Journal of Biosystems Engineering
• /
• v.23 no.4
• /
• pp.327-334
• /
• 1998

This work was intended to determine the optimum values of the cab suspension parameters by a simulation method in order to minimize the seat accelerations of agricultural tractors in the frequencies lower than 50Hz. A dynamic model of cab motions was developed and verified using a tractor excited over half-sine bumps on a concrete test road. A simulation program based on the model was also developed. A method was proposed to determine the optimum values of the suspension parameters. It was found that the natural frequencies of the cab and seat suspensions must be apart as far as possible until the sum of seat and cab accelerations is minimized, which also reduces the seat accelerations maximally.

• Journal of Biosystems Engineering
• /
• v.15 no.4
• /
• pp.298-309
• /
• 1990

A mathematical model was developed to simulate sideways overturning of agricultural tractor-trailer systems. Sideways overturn of a tractor-trailer system was described by oscillatory motions of the tractor with respect to the first and second tipping axes, and of the trailer with respect to the drawbar hitch point when either the tractor or trailer rides over an obstacle on slopes. By a computer simulation, critical slope angles of the ground on which the tractor-trailer system is likely to sideways overturn were evaluated under the given operational conditions. Validity of the proposed mathematical model was proved by comparing the results of computer simulation and experiment with a model tractor-trailer system. A close agreement was observed between the two results.

• Journal of Biosystems Engineering
• /
• v.18 no.3
• /
• pp.191-198
• /
• 1993

Vertical and horizontal ride vibrations of the selected agricultural tractors were measured and evaluated with respect to the ISO 2631 'guide for the evaluation of human exposure to whole body vibration'. Evaluation showed that at the normal transportation speeds of 1.4~20km/h on both the concret and ground surfaces tractor drivers were exposed to the vibrations whose magnitudes exceed the 8 hour fatigue decreased proficiency boundary in the frequency ranges of 2~16Hz in vertical and 1~2Hz in horizontal directions. Considering that tractor operation becomes as one of the specialized job for the future farming in Korea, measures must be made to protect the drivers against harmful ride vibrations of agricultural tractors.

• Journal of Biosystems Engineering
• /
• v.17 no.3
• /
• pp.223-228
• /
• 1992

This study was conducted to develop an electro-hydraulic three-point hitch control system using an electro-hydraulic servo valve and microcomputer and to investigate the performance of the three-point hitch control system through indoor and field experiments. 1. The results from indoor experiments coincided with those from computer simulation reported in the previous paper. However, the draft control with the value 4 of Kd showed a slight sustained oscillation after it reached the draft set. 2. From the field experiments, it appeared that the RMS errors increased with the ground speed of tractor. In position control, the three-point hitch control system with electro-hydraulic servo valve showed better performance than that with on-off electro-magnetic valve in the ground speed less than 1.6 m/s. In draft control, however, there was no significant differece in performance between those two systems. 3. In depth control, the both types of electro-hydraulic three-point hitch control system showed better performance than the conventional mechanical-hydraulic three-point hitch control system.

• Journal of Biosystems Engineering
• /
• v.17 no.4
• /
• pp.326-335
• /
• 1992

This study was carried out to develop a measurement and analysis system of ride vibrations of tractors. The system consists of a portable digital computer, a PCL-812 PG interface card for A/D conversion, two accelerometers, two signal conditioners, a DC-AC power inverter and a DC power supplier. The computer programs installed in the system for data acquisition and analysis were also developed. It was intended that the system should be cheap enough to be afforded by college laboratories but reliable in its functions of measurement and analysis. Characteristics of the components and methods used in the system development were discussed.

• Journal of Biosystems Engineering
• /
• v.35 no.2
• /
• pp.85-90
• /
• 2010

This study was carried out to develop turning radius measuring method and device of using a DGPS speed sensor for agricultural tractors. The measurement system consisted of a DGPS speed sensor, a data acquisition device, a touch panel, a photo sensor, a radio modem and a notebook computer. Three methods were developed: average of turning speed-time method, integral of turning speed-time method, and speed-heading angular velocity method. Best method was average of turning speed-time method which could be used with a maximum error 2.7 cm.

• Journal of Biosystems Engineering
• /
• v.17 no.1
• /
• pp.18-26
• /
• 1992

A mechanical-hydraulic hitch control system has been adapted to most agricultural tractors. But it has various defects due to friction, inertia and hysteresis. Recently a number of electronic-hydraulic hitch control systems have been developed in several countries to improve control performance of the agricultural tractors equipped with a mechanical-hydraulic hitch control system. This study was conducted to develop a new electronic-hydraulic hitch control system using an electro-hydraulic servo valve instead of an on-off valve and to carry out computer simulation of the system. According to the result of computer simulation, the control system showed the best performance when the proportional constants were 9 and 4 for position and draft control respectively. The step and frequency responses were improved as flow rate increased.

• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.20-32
• /
• 1982

This survey was conducted to investigate the present status of farm tractor utilization for obtaining a basic reference to the establishment of the government's agricultural mechanization strategies. Thirty two counties from the eight provinces except Jeju were covered in this study. From these selected areas, 433 sample farms having farm tractor were taken to obtain the general informations by the enquete, and 93 sample farms among them to investigate the status of daily tractor use in the year of 1980. The analyzed results are summarized as follows: 1. Farm tractors owned by the rice-oriented farms holds 71.5 percent of the total number of tractors the livestock-oriented farms 17.0 percent, and the orchard-oriented farms 7.0 percent. Among the farm tractors 64.3 percent was a large size (46ps) and 35.7 percent a small size(19~23ps). 2. Most of the tractors surveyed were equipped with the essential attachments such as plow and rotavator. About 18 percent of the tractor owners had no trailer, which seemed too high considering the large percentage of tractor use for transportation. The availability of other attachments was very low except a grader on the rice-oriented farms and a hay harvester and a front loader on the livestock-oriented farms. 3. The average size of farm was 3.9 hectare for the rice-oriented farms, 13.9 hectare for the livestock-oriented farms and 7.4 hectare for the orchard-oriented farms. It was obious that the average farm size of was too small compared to the theoretical machine capacity of the tractors. 4. About 70 percent of the tractor operators were in the age of twenties and thirties. About 90 percent of them had an educational level of middle school graduate or above even though their technical level was very low. 5. Any particular problem in tractor use was not found in this survey. From the farmer's preference for purchasing a new tractor, however, it is estimated the demand on a 20-30ps tractor will be more increased. 6. The average annual use of tractor was of about 100 days or 400 hours. It appeared that the rice-oriented farms used most with 412.4 hours per year, and followed by the livestock-oriented farms with 403.6 hours, the orchard oriented farms with 377.7 hours. 7. Among the total hours of tractor use, 47.3 percent was for transportation, and 41.6 percent was for plowing and rotary tillage. The largest portion of the annual tractor use was taken by transportation on the livestock-oriented farms, by land preperation on the rice-oriented farms, and by loading and chemical spraying on the orchard-oriented farms. 8. The hours of tractor use had a peak in May. The hours of use for own farm was remarkably different among the different farm oriented, but there was no considerable difference between the too different sizes of tractor. 9. The hours of tractor use decreased as the age of the operator or the educational level increased. The reason might be that the operators who had a high educational level or were older had a tendency of disliking custom works. 10. The average custom use of tractor was 171.3 hours per year, and the ratio of custom work was 63.7 percent on the rice-oriented farms, 31.7 percent on the livestock-oriented farms and 22.4 percent on the orchard-oriented farms. Among the custom works, the most popular one was the grader leveling. 11. The charge on custom work was about 40,000 Won per hectare for plowing and rotary tillage, and it was the most expensive in the southeastern region, and next followed by the southwestern region. 12. The average plowing capacity of the small tractor was 7.8 hours per hectare in the paddy field, and that of the large tractors was 4.3 hours per hectare. The average rotary-tilling capacities of the small and the large tractors were 6.5 and 4.3 hours per hectare, in the paddy field respectively.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.305-314
• /
• 2009

The purpose of this paper was to design an effective control system of 1-axis exciter for a seat vibration test of agricultural tractors using MATLAB simulation. The developed simulation model was composed with a hydraulic pump, a hydraulic servo valve, a hydraulic cylinder and load system. Also it was verified by comparing the simulation results with experimental results of actual control system in order to optimize the control performance. And in order to improve its control performance, the designed PID controller in this research was tuned using Ziegler-Nichols 2nd law and zero's moving method of PID controller's transfer function. As the result of these research, the developed position control system was able to control the system's position accurately within 5% errors.