• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.2869-2871
• /
• 1999

본 연구는 포항제철 STS 냉연공장의 형상 제어에 관한 것이다 당사의 냉간 압연기는 Sendzimir mill로서 상하 롤(Roll)이 10단씩 구성된 20단 압연기이다. 본 압연기에 의한 575 냉연강판의 형상제어는 현재 조업자의 수동운전으로 구동되고 있으며 구동기는 AS_U Roll 8 개와 Intermediate Roll 2 개의 10 개로 구성되어 있다. 구동기의 특성은 solenoid 형태와 유압식으로서 응답성이 빠르지 뭇하다. 본 연구는 위와 같은 특성을 지닌 냉간 압연기를 가지고 퍼지 제어에 의한 자동제어의 구현에 관한 것이다. 본 연구에 사용된 퍼지 제어기는 형상 강판의 두께 Roll 속도, AS_U Roll과 IMR의 현 위치 강종 강판의 폭, 강판의 장력 등의 입력을 고려하여 제어기의 출력인 AS_U Roll 8 개의 위치 값과 IMR 2 개의 위치 값을 결정한다. 현재 실 프로세서에 적용중이며 형상제어 정도가 양호하다. 본 연구의 효과는 형상제어의 자동화 및 형상 정도 향상을 통한 조업 안정화에 있다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.433-438
• /
• 2012

We have studied on welding dissimilar materials of Carbon steel SCP1-S by using laser beam. In this research we have performed some experiments to know the possibility of welding dissimilar materials using laser beam and magnetic fields by adjusting the power output of 35W laser. Other conditions of the experiments were as follows : the welding speed was varied in the range 10 m/min nitrogen gas was used as shield gas, the flow value of shield gas was ranged 10 L/min. In order to ascertain of the welded surface, we have done the tensile strength testing, the hardness testing and the microscope observation. As a result, we have found that tensile strength was the highest at the condition of the welding speed of 10mm/s, the flow value of 10 L/min, the gap of two materials 0, and the use of nitrogen gas. Above testings have also showed that the tensile strength was generally satisfactory since the penetration of welding was almost complete due to the thinness of the materials. In addition, the formation of the welded area was excellent when it had the highest tensile strength.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.42-49
• /
• 2018

In steel industries, cold-rolled sheet manufacturing is one of the links between the front and rear important industries for national competitiveness and high value-added production. In particular, in small and medium-sized enterprises, one of the major problems is the carbonization phenomenon of the steel sheet during the annealing process. Carbonization occurring on the surface of the coil help reduce steel production. After conducting various experiments to identify the cause of carbonization on the surface of a cold-rolled steel, the following results were obtained: (1) An analysis of the rolling oil, which is used in the field, revealed it to contain approximately 40 ppm carbonized material. (2) A comparison of the thermal denaturation characteristics of the fresh rolling oil and using rolling oil by FT-IR analysis showed that thermal denaturation had occurred, as shown by the significant decrease in the relative intensity of the 2900 and $1750cm^{-1}$ peaks. (3) The thermal decomposition of the rolling oil took place for the rolling oil at approximately $220^{\circ}C$. Furthermore, annealing experiments at $200^{\circ}C$ showed that the carbonization phenomenon of the sample was not observed. On the other hand, carbonization was observed at temperatures higher than $240^{\circ}C$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.1
• /
• pp.34-43
• /
• 1994

In order to improve thickness profile of cold rolled steel strip, a computer simulation and actual cold rolling experiments on a 4-high tandem cold mill were carried out. In this study, tapered barrel end at top work roll and incurved barrel body at bottom work roll were examined for reducing edge drop and threading of stripe. Also, the most effective stand of tandem cold mill and magnitude of optimal taper crown at several stand were investigated under a typical rolling condition. From actual rolling experiments, it was verified that thickness deviation over strip width could be improved up to 1.06% by applying tapered and incurved work roll only at the second and up to 0.89% by applying them at both the second and the third stand.

• Journal of Welding and Joining
• /
• v.31 no.1
• /
• pp.51-57
• /
• 2013

Residual stress caused in the weldments with high restraint force are often observed during welding in the weldments of Inner and outdoor materials or radial tanks. The reason is that quantitative analysis about thermal stresses during laser welding is lacking for this weldments. To verify Finite Elements Method (FEM) theory, the temperature was measured with thermocouple in a real time in this paper. Also analysis of the thermal stress for welding condition is performed by Comsol program package on various welding condition in SCP1-S butt welding. The principal stress in laser welding process is seen through the width direction. Also, it was confirmed that a change in base metal by thermal expansion made the stress in width direction stronger. Base metal close to the weld bead as the process progresses to the tensile stress in the compressive stress was varied. It was shown that the change of stress was quantitative from the bead at a certain distance.