• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 1999.11a
• /
• pp.95-99
• /
• 1999

자연에너지와 전기에너지를 조합하여 냉방과 난방을 수행할 수 있는 방법중의 하나로 히트펌프 이용기술이 있으며, 국내의 경우 히트펌프는 주로 냉방 또는 냉동을 목적으로 이용되고 있으나, 1980년 이후 전기가 풍부한 경제선진국을 중심으로 난방 또는 냉난방겸용의 히트펌프가 개발되어 주택, 빌딩, 온실 등의 공조시스템에 이용되고 있다. (중략)

• The Journal of Sustainable Design and Educational Environment Research
• /
• v.4 no.4
• /
• pp.1-18
• /
• 2004

Research has been carried out to study thermal environment in a classroom under three kinds of air diffusion temperature and six kinds of air diffusion direction for ceiling type air conditioner. The velocity and temperature distributions of air in the room calculated by 3-dimensional numerical method(PHOENICS), This present study was also conducted to calculate the Air Diffusion Performance Index(ADPI) for cooling conditions and Predicted Percentage of Dissatisfied(PPD) for heating conditions. This analysis shows that the optimum angle of ceiling type air conditioner's diffusion is $15{\sim}30^{\circ}$ for cooling mode and about $15{\sim}45^{\circ}$ for heating mode in these calculating conditions. And also analysis has been carried out to evaluate thermal comfort of vertical and horizontal cross section of classroom.

• 한국연소학회:학술대회논문집
• /
• 1999.10a
• /
• pp.111-115
• /
• 1999

In order to enhance the burner performance of household gas fired absorption chiller/heaters, the operating condition(excess air $\approx$ 10%) of the burner currently being used was required to be optimized. In this regard, we examined where the $CO_{\min}$. emission limit was located between blow off and yellow tip limit and how much amount of excess air was exhausted by means of observing blow off and yellow tip limit. It was found that the $CO_{\min}$ limit(excess air ${\approx}$ 4%) was determined near the yellow tip limit. The effect of exhaust pressure on the $CO_{\min}$. limit was that, if exhaust pressure was higher than that in steady condition, higher air blower fan rpm is demanded to maintain the $CO_{\min}$ limit. Therefore, it was necessary to optimize the operating condition of burner in terms of a thermal efficiency and safety.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.10
• /
• pp.679-686
• /
• 2007

The cooling load in winter season is significant in many commercial buildings and hotels because of the usage of office equipments and the high efficiency of wall insulation. The development of a multi-heat pump that can cover heating and cooling simultaneously for each indoor unit is required. In this study, a 4-room simultaneous heating and cooling heat pump system was designed and its performance was measured at each operating mode. The system used R-410A and adopted variable speed compressor. The problems on the designed system were analyzed and defined. In addition, the solutions of the problems were suggested to improve system efficiency and to obtain the stable operation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.17-22
• /
• 2014

Recently, the quick heating performance is an important issue in the car because engine power becomes so high. So car makers have been adapted the additional heating devices as like PTC(Positive Temperature Coefficient) heater. And the quick cooling performance is also important issue because its result is used in the IQS(Initial Quality Study). In this paper, control of the HVAC(Heating, Ventilation and Air Conditioning) intake door has been studied for the quick heating and cooling performance. Heating performance is improved $4.0^{\circ}C$ at $-20^{\circ}C$ ambient temperature after 20 minutes. And cooling performance is improved $1.5^{\circ}C$ at $35^{\circ}C$ ambient temperature after 10 minutes. In addition, intake door control system brings on the cost reduction because the flab door can be eliminated. This intake door control system has been adapted to the new developing cars.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.9
• /
• pp.738-743
• /
• 2003

In the present study, the heating and cooling characteristics of system air-conditioner using a PWM compressor or a BLDC inverter compressor are investigated by the psychometric calorimeter using air enthalpy method. Cooling and heating capacities, power inputs and COPs are measured at the low, moderate, high loads under the cooling and heating standard conditions. At cooling conditions, the capacity of the PWM system is larger than that of the inverter case. Due to large power input, however, low COPs are measured under total load ranges. At heating conditions, the capacity of the PWM method is a little larger than that of the inverter case, except high load range. Since power input is low, large COPs are measured at moderate and high load ranges, which are different from cooling data. This shows that the PW system compared with the inverter case has good energy consumption efficiency at moderate and high load ranges except low load range. And when the system A/C is operated under the cooling and heating standard conditions, COPs are nearly uniform at total load ranges.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.77-85
• /
• 2010

In this paper, A new integrated energy simulation results of LED lamp are presented to use it effectively in the office buildings. Generally LED lamp has many advantages in comparison with a general lamp such as long life and no pollution problem like the mercury. It also is excellent in color rendering and small consumption electric power. However LED lamp has some disadvantages to compare to general fluorescent lamp. It is small light flux about 50[%] and narrow light distribution than fluorescent lamp. Therefore, to apply LED lamp in an office building, the illuminance distribution with an environment analysis and cooling, heating and light energy has to be analyzed. The purpose of this study is to analyze light environment, light, cooling and heating energy simulation in office building.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.370-375
• /
• 2007

The cooling load in winter season is significant in many commercial buildings and hotels because of the usage of office equipments and high efficiency of wall insulation. The development of a multi-heat pump that can cover heating and cooling simultaneously for each indoor unit is required. In this numerical study, a 4-room simultaneous heating and cooling heat pump system was modeled and its performance was calculated at each operating mode. Also, performance analysis was compared with experimental results.

• Journal of the Korean Solar Energy Society
• /
• v.24 no.3
• /
• pp.55-63
• /
• 2004

빛이 입사각별로 태양투과율이 제어되어지는 첨단 창과 같은 물체를 통과할 때 투과되는 성분은 직달투과와 산란투과성분으로 볼 수 있다. 직달투과는 물체를 통과하면서 일정한 방향으로 굴절되어 투과되는 성질을 말하고, 산란투과는 직달투과를 제외한 나머지 방향의 성분들의 형태를 말한다. 이러한 첨단 창의 냉난방부하에 미치는 에너지성능을 평가하기 위해서는 산란투과에 대한 정보가 필요하고, 이에 대한 물리적 변수는 입사각, 출력각, 양방향 투과율 분산함수인 BTDF로 정의된다. 본 논문에서는 3개의 서로 나른 첨단 창 (1) $42^{\circ}/5^{\circ}$ 프리즘 창 판넬, (2) 레이저 컷 판넬 (3) $45^{\circ}$ 프리즘 3M 필름의 BTDF 데이터 획득을 위한 실험 방안을 소개하고, 실험을 통해 획득한 정보를 이용하여 계산식과 비교 검증을 하였다. 따라서 이 검증된 방안을 이용하여 지역별 냉난방 부하를 최소화 할 수 있는 입사각별로 태양 투과율 제어 판넬을 선정할 수 있게 되었다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.5
• /
• pp.314-320
• /
• 2008

The cooling load in winter is significant in buildings and hotels because of the usage of office equipments and the improved wall insulation. Hence, a multi~heat pump is required to cover heating and cooling simultaneously for each indoor unit. In this study, the operating characteristics and performance of a simultaneous heating and cooling heat pump in the cooling-main operating mode were investigated experimentally. The system adopted a variable speed compressor using R410A with four indoor units and one outdoor unit. In the cooling-main mode, the heating capacity decreased due to reduction of flow rate to the indoor unit under heating mode operation. The EEV opening was adjusted to increase flow rate to the indoor unit under heating mode operation. The total capacity and COP in the cooling-main mode increased by 20.5% and 29.2%, respectively, compared with those in the cooling-only mode.